American Standard T430.508.295 Installation guide
- Category
- Sanitary ware
- Type
- Installation guide
This manual is also suitable for
American Standard T430.508.295 is a bath and shower trim kit designed to provide a stylish and functional upgrade to your bathroom. With its sleek design and durable construction, this trim kit is built to last. The kit includes a variety of features to enhance your showering experience, including a pressure-balancing valve that helps to maintain a consistent water temperature, even when other water sources in your home are being used.
American Standard T430.508.295 is a bath and shower trim kit designed to provide a stylish and functional upgrade to your bathroom. With its sleek design and durable construction, this trim kit is built to last. The kit includes a variety of features to enhance your showering experience, including a pressure-balancing valve that helps to maintain a consistent water temperature, even when other water sources in your home are being used.
BATH AND SHOWER TRIM KIT
M 9 6 5 0 5 4 R E V. 1.1
To assure proper positioning in relation to wall,
note roughing-in dimensions.
ROUGHING-IN DIMENSIONS
Certified to comply with ANSI A112.18.1
Installation
Instructions
T430.508
T430.507
THREADED INLETS (STOPS)
INLETS
1/2" NPT
(13mm)
5-7/8"
(149mm)
INLETS 1/2" NPT (13mm}
OUTLETS
1/2" NPT
(13mm)
OUTLETS
1/2" NPT
(13mm)
3-3/8"
(86mm)
3-3/8"
(86mm)
3-3/8"
(86mm)
THREADED INLETS
Recommened Tools
Flat Blade Screwdriver
Adjustable Wrench
Channel Locks
Plumbers' Putty or Caulking
Phillips Screwdriver
4" (102mm)
BOTTOM OF TUB
74" FOR HEAD
CLEARANCE
(1880mm)
18" OPTIONAL
(457mm)
1/2" COPPER
OPTIONAL TO FINISHED
FLOOR USUALLY
BETWEEN 65'' AND 80''
(1651 and 2032mm)'
TOP OF TUB RIM
Teflon Tape
SHR. 1/2" NOM.(13mm)
COPPER SWEAT
TUB 1/2" NOM. (13mm)
COPPER SWEAT
4-1/16"
(103mm)
5-7/8"
(149mm)
INLETS
4-1/16"
(103mm)
4-1/16"
(103mm)
INLETS
1/2" NOM.
(13mm)
COPPER
SWEAT
SHR. 1/2" NOM.
(13mm)
COPPER SWEAT
TUB 1/2"
(13mm) NOM.
COPPER SWEAT
2"
SWEAT
INLETS
SWEAT
INLETS (STOPS)
INLETS
1/2" NOM.
(13mm)
COPPER
SWEAT
FINISHED WALL
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
BERWICK
™
/ BOULEVARD
™
1/2" NPT
(13mm)
1-5/8" to 3-1/4"
(41 to 83 mm)
1-5/8" to 3-1/4"
(41 to 83 mm)
5-5/8" REF.
(143mm)
8-1/8" REF.
(206mm)
2-3/8" D.
(60mm)
4-7/8" REF.
(124mm)
7-1/4"
(184mm)
1-3/4
"
(44 mm)
M 9 6 5 0 5 4 R E V. 1.1
1
INSTALL VALVE TRIM
1
1
Figure 1.
Figure 2.
Figure 3.
7
3
5
6
4
5
2
1
Figure 1. Remove plaster guard from valve. Push CAP (1)
over VALVE CARTRIDGE (2) until seated against stop.
Figure 2. Push ESCUTCHEON HOLDER (3) onto CAP (1)
and attach to valve body with LONG SCREWS (4). Mount
ESCUTCHEON SUPPORT (5) to ESCUTCHEON HOLDER (3)
with 4 SHORT SCREWS (6).
Figure 3. Install ESCUTCHEON (7) onto CAP (1) and push
flush against finished wall. Escutcheon (7) will snap fit onto
ESCUTCHEON SUPPORT (5).
3
INSTALL HANDLE
3
1
5
Hold ADAPTER (1) onto VALVE STEM (2) and install
ADAPTER SCREW (3) through ADAPTER (1) into
VALVE STEM (2).Tighten ADAPTER SCREW (3) to
secure ADAPTER (1) to VALVE STEM (2).
Install HANDLE BASE (4) onto ADAPTER (1). Insert
SET SCREW (5) into HANDLE BASE (4). Align
HANDLE BASE (4) and tighten with HEX WRENCH
(6) supplied.
2
6
PLSTER
GUARD
5
1
2
6
3
4
APPLY SEALANT OR
TEFLON TAPE TO THREADS
O-RING
4
2
INSTALL TRIM
Remove PIPE PLUG and CAP (1, 2) from shower pipe and tub
filler pipe.
Install SHOWER ESCUTCHEON (3) onto SHOWER
ARM (4). Apply sealant or Teflon tape to threads on
both ends of SHOWER ARM (4) and thread longer
leg of SHOWER ARM (4) into shower elbow.
Thread SHOWER HEAD (5) onto SHOWER ARM (4).
Install SLIP-ON TUB SPOUT (6). Tighten with
HEX WRENCH supplied.
Important: Do not overtighten Set Screw.
CAUTION: Protect finish on SHOWER
HEAD and TUB SPOUT when installing.
Note: Apply sealant or Teflon Tape to shower arm.
HEX WRENCH
1-3/4"
M 9 6 5 0 5 4 R E V. 1.1
5
Remove HANDLE (see step 3 and reverse).
Remove ESCUTCHEON and CARRIDGE CAP (see step 1 and reverse).
Shut off water supply by either closing off main water supply, or closing off
the hot and cold CHECK STOPS on valve.
TO GAIN ACCESS TO VALVE FOR SERVICING
Remove CARTRIDGE (1) by removing CARTRIDGE SCREWS (2). Remove three SCREWS (3) from FIXATION RING (4) and
pull out PRESSURE BALANCING (5) unit.
Clean SEALS (9) on base of CARTRIDGE (1). Check base of PRESSURE BALANCING UNIT (5) and clean O-RINGS (6). Remove
CAPS (7) and check O-RINGS on inside of CAPS (7). Clean inside sealing surfaces of VALVE BODY (8).
Re-assemble PRESSURE BALANCING UNIT (5) and CARTRIDGE (1). Tighten all screws.
Turn on water supply and see above for installing TRIM and HANDLE.
VALVE LEAKS WHEN SHUT OFF
BACK TO BACK INSTALLATION
BACK TO BACK INSTALLATION
ROTATE 180˚
Remove PRESSURE BALANCE UNIT (5).
Remove CAPS (7) and clean valve thoroughly.
Examine balancing unit and check condition of O-ring on end of piston. Piston should move back and forth. Order Repair
Part M952100-0070A if balancing unit is defective.
Replace CAPS (7) and install PRESSURE BALANCE UNIT (5). Make sure inlets line up with two holes in bottom of casting.
Top flange should butt-up against top of casting.
Remove PRESSURE BALANCE UNIT (5). Rotate PRESSURE BALANCE UNIT (5) 180˚ so that the inlets face up and the
large outlet port faces down.
Push PRESSURE BALANCE UNIT (5) in casting make sure inlets line up with holes in bottom of casting. Top flange should
butt up against top of casting.
Reassemble FIXATION RING (4) and CARTRIDGE (1).
UNABLE TO MAINTAIN CONSTANT TEMPERATURE
1
2
9
5
5
7
8
6
4
3
INLETS
LARGE OUTLET
6
1
5
1
3
1
1
9
7
5
3
1
0
1
5
1
3
1
1
9
7
5
3
1
1
5
1
3
1
1
9
7
5
3
1
COLDER
(Larger Numbers)
0 1 3 5 7 9 11 13 15
HOTTER
(Smaller Numbers)
0 1 3 5 7 9 11 13 15
ADJUST HOT LIMIT STOP
By restricting HANDLE rotation and limiting the amount of hot
water allowed to mix with the cold, the HOT LIMIT SAFETY
STOP (1) reduces risk of accidental scalding. To set the maximum
hot water temperature of your faucet, all you need to do
is adjust the setting on the HOT LIMIT SAFETY STOP (1).
4
Turn CARTRIDGE STEM (2) to the OFF position (coldest setting) before
making adjustment to HOT LIMIT STOP (1). Use aflat blade screwdriver to pry
free the HOT LIMIT SAFETY STOP (1). Pull forward and rotate counterclockwise
one number to limit hot water temperature. Use ARROW (3) on CARTRIDGE (4)
and NUMBERS (5) on HOT LIMIT STOP (1) for indication.
1
5
4
3
1
5
4
3
2
2
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
M 9 6 5 0 5 4 R E V. 1.1
M907053-YYY0A
CARTRIDGE CAP
MODEL NUMBER
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2010
A918477-0070A
HANDLE SCREW
M918039-0070A
HANDLE ADAPTER
BATH AND SHOWER TRIM KITS
M950278-YYY0A
DIVERTER SPOUT
(SLIP-ON)
M962848-YYY0A
HANDLE KIT
023820-0070A
SET SCREW
A953876-YYY0A
ESCUTCHEON
M962642-0070A
ESCUTCHEON HOLDER
CHROME
SATIN NICKEL
002
295
Replace the "YYY" with
appropriate finish code
IN MEXICO 01-800-839-1200
T430.508 / T430.507
BERWICK
™
/ BOULEVARD
™
A912632-0070A
O-RING
1660613-YYY
SHOWER HEAD
M962493-YYY0A
SHOWER ARM & FLANGE
-
1
-
2
-
3
-
4
American Standard T430.508.295 Installation guide
- Category
- Sanitary ware
- Type
- Installation guide
- This manual is also suitable for
American Standard T430.508.295 is a bath and shower trim kit designed to provide a stylish and functional upgrade to your bathroom. With its sleek design and durable construction, this trim kit is built to last. The kit includes a variety of features to enhance your showering experience, including a pressure-balancing valve that helps to maintain a consistent water temperature, even when other water sources in your home are being used.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
American Standard BERWICK T430.50X Installation guide
-
-
-
-
American Standard M968628 REV.1.3 User manual
-
-
-
-
-