Commercial Electric EFG8913L-2 Operating instructions

Page 1

INSTRUCTION MANUAL

3LT Interior Pendant

The Home Depot SKU 889-030 (UPC 6940500304090)

Page 2

Thank you for purchasing this Commercial Electric interior pendant. This

product has been manufactured with the highest standards of safety and

quality.

FEATURES:

1. Three-light interior pendant in brushed nickel finish with frosted white

glass.

2. Standard 96-inch wire and 84-inch chain for open entry-way and cathedral

ceiling installations.

3. This fixture has been engineered to safely use three 60 watt medium base

incandescent light bulbs (do not exceed 60 watts each) (not included).

4. For energy savings, this fixture has been engineered to safely use three

standard base compact fluorescent light bulbs (for equivalent light output,

do not exceed 15 watts each) (not included).

QUESTIONS, PROBLEMS, MISSING PARTS:

Before returning to your local The Home Depot, please call our Customer

Service Team at 1-877-527-0313 or visit www.homedepot.com. Please

reference your SKU 889-030 or UPC 6940500304090.

Page 3

CAUTION:

1. Before starting installation of this fixture or removal of a previous fixture,

disconnect the power by turning off the circuit breaker or by removing the

fuse at the fuse box.

2. CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY

ELECTRICAL QUESTIONS.

3. If you have any non-electrical questions about this fixture, please contact

our Customer Service Team at 1-877-527-0313 or visit

www.homedepot.com. Please reference your SKU 889-030 or UPC

6940500304090.

4. Keep your receipt and these Instructions for Proof of Purchase.

TOOLS REQUIRED FOR ASSEMBLY & INSTALLATION

(not included):

3 Light Bulbs Safety Goggles Ladder Gloves Wire Strippers

(60 watt maximum)

(or CFL equivalent)

Flathead Screwdriver Phillips Screwdriver Electrical Tape Wire Cutters Pliers

Page 4

PARTS INCLUDED FOR ASSEMBLY (parts are not to scale):

1ea Canopy (#1) 1ea Screw 7 feet Chain (#3) 1ea Ring (#4) 1ea Loop (#5)

Collar Loop (#2)

1ea Nipple A (#9) 1ea Steel Washer (#10) 1ea Plastic Washer (#11) 1ea Shade (#12)

1ea Washer (#13) 1ea Bottom Cover (#14)

1ea Finial (#15)

ASSEMBLY INSTRUCTIONS:

1. Carefully unpack the fixture. Lay out all parts on a clean surface.

2. Use pliers and a screwdriver to twist open the link (cover the chain with cloth to prevent

damage to the link finish) at the end of the Chain (#3) not attached to the Screw Collar

Loop (#2). To avoid damage to the link, only open the link enough to hook it onto the Loop

(#5). Hook the open link to the Loop (#5) and then close the link.

3. Weave the fixture wires up through the Loop (#5), through the Chain (#3), through the

Ring (#4), through the Screw Collar Loop (#2), through the Canopy (#1), and through the

Nipple (#21 on Page 7) on the Mounting Strap (#20 on Page 7). Screw the Nipple (#21)

into the Screw Collar Loop (#2).

4. Unscrew the Finial (#15) from Nipple A (#9). Screw Nipple A (#9) about a quarter-inch

into the Bracket (#8).

5. Place the Steel Washer (#10), the Plastic Washer (#11), the Shade (#12), the Washer (#13)

and the Bottom Cover (#14) around Nipple A (#9). Secure them by screwing the Finial

(#15) onto Nipple A (#9).

6. Install three 60 watt medium base incandescent light Bulbs (#7) (not included) or three

equivalent standard base compact fluorescent light bulbs (not included) in the three

Sockets (#6) in the fixture.

Page is loading ...

Page 6

PARTS INCLUDED FOR INSTALLATION (parts are not to scale):

3ea Wire Connectors (#17) 1ea Ground Screw (#18) 1ea Hex Nut (#19)

1ea Mounting Strap (#20) 1ea Nipple (#21) 2ea Outlet Box Screws (#22)

INSTALLATION INSTRUCTIONS:

1. Screw the Nipple (#21) a half-inch into the Mounting Strap (#20). Tighten the Hex Nut (#19)

against the Mounting Strap (#20) to secure the Nipple (#21). Attach the Mounting Strap (#20) to

the Outlet Box (#16) using the two Outlet Box Screws (#22). [Make sure the longer end of the

Nipple (#21) is facing outside when the Mounting Strap (#20) is attached to the Outlet Box (#16).]

2. Adjust the Chain (#3) to required height by using pliers and a screwdriver to twist open (cover

the chain with cloth to prevent damage to the link finish) the link of Chain (#3) attached to the

Loop (#5), lifting the fixture and attaching to a link closer to the ceiling. To avoid damage to the

link, only open the link enough to hook it onto another link. The fixture can be raised and

lowered in this manner until the desired height is achieved. Next, use pliers to twist open (cover

the chain with cloth to prevent damage to the link finish) the first unused link of Chain (#3).

Remove and save the excess chain. Pull the excess fixture wires through the Nipple (#21) into the

Outlet Box (#16). Wires may be left at full length or shortened as determined by space in the

Outlet Box (#16) to make the wire connections.

3. Wrap the ground wire from the fixture around the Ground Screw (#18) on the Mounting Strap

(#20), and then connect the ground wire from the fixture to the ground wire from the Outlet Box

(#16). Connect the wire without writing on it (with raised ribs) from the fixture to the white wire

(neutral wire) from the Outlet Box (#16). Connect the wire with writing on it from the fixture to

the black wire (live wire) from the Outlet Box (#16). Cover the three connections using the three

Wire Connectors (#17). Wrap the three wire connections with electrical tape for a more secure

connection. Position the wires back inside the Outlet Box (#16). Note: If you have electrical

questions, consult your local electrical code for approved grounding methods.

4. Place the Canopy (#1) over the Nipple (#21) all the way to the ceiling. Tighten the Ring (#4) onto

the Screw Collar Loop (#2) until the Canopy (#1) is held firmly against the ceiling.

5. Installation is complete. Turn on the power at the circuit breaker or fuse box. Turn the light

switch on to activate the fixture.

Page is loading ...

Page 8

TROUBLESHOOTING:

PRODUCT MAINTENANCE:

1. To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean

water, never a solvent) to wipe the glass and surface of the fixture.

2. To clean the inside of the fixture, first disconnect power to the fixture by turning off the

circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly

dampened clean cloth (use clean water, never a solvent) to wipe the inside glass and interior

surface of the fixture.

3. Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry soft

cloth to dust or wipe carefully.

LIMITED WARRANTY

The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period

of five (5) years from date of purchase. This warranty applies only to the original consumer purchaser and only to

products used in normal use and service. If this product is found to be defective, the manufacturer’s only

obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer’s discretion,

provided that the product has not been damaged through misuse, abuse, accident, modifications, alterations,

neglect or mishandling. This warranty shall not apply to any product that is found to have been improperly

installed, set-up, or used in any way not in accordance with the instructions supplied with the product. This

warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration,

or faulty installation, or any other failure not relating to faulty material or workmanship. This warranty shall not

apply to the finish on any portion of the product, such as surface and/or weathering, as this is considered normal

wear and tear. The manufacturer does not warrant and specially disclaims any warranty, whether express or

implied, of fitness for a particular purpose, other than the warranty contained herein. The manufacturer

specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage,

including but not limited to any labor / expense costs involved in the replacement or repair of said product.

Problem Possible Cause Corrective Action

Light Bulb will not

illuminate.

1. Light bulb is burned out. 1. Replace light bulb.

2. Power is off. 2. Make sure power supply

is on.

3. Faulty wire connection. 3. Check wiring.

4. Faulty switch. 4. Test or replace switch.

Fuse blows or circuit breaker

trips when light bulb is

illuminated.

Crossed wires or power wire

is grounding out.

Check wire connections.

Page 9

MANUAL DE INSTRUCCIONES

Colgante para Interiores de 3 Luz

The Home Depot SKU 889-030 (UPC 6940500304090)

Page is loading ...

Commercial Electric EFG8913L-2 Operating instructions

Commercial Electric EFG8913L-2 Operating instructions

in other languages

Related papers

Other documents