Page 1
INSTRUCTION MANUAL
5LT Interior Chandelier
Lucerne Collection
The Home Depot SKU 788-942(UPC 6940500313931)
Page 2
Thank you for purchasing this Hampton Bay interior chandelier. This product
has been manufactured with the highest standards of safety and quality.
FEATURES:
1. Five-light interior chandelier in Polished Nickel finish with Fabric shades.
This chandelier is a part of the matching Lucerne collection available at
The Home Depot.
2. Standard 96-inch wire and 72-inch chain for open entry-way and cathedral
ceiling installations.
3. This fixture has been engineered to safely use up to five 60 watt
candelabra incandescent light bulbs (do not exceed 60 watts each) (not
included).
4. For energy savings, this fixture has been engineered to safely use five
candelabra compact fluorescent light bulbs (do not exceed 15 watts each)
(not included).
QUESTIONS, PROBLEMS, MISSING PARTS:
Before returning to your local The Home Depot, please call our Customer
Service Team at 1-877-527-0313 or visit www.homedepot.com. Please
reference your SKU788-942or UPC 6940500313931.
Page 3
CAUTION:
1. Before starting installation of this fixture or removal of a previous fixture,
disconnect the power by turning off the circuit breaker or by removing the
fuse at the fuse box.
2. CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY
ELECTRICAL QUESTIONS.
3. If you have any non-electrical questions about this fixture, please contact
our Customer Service Team at 1-877-527-0313 or
visitwww.homedepot.com. Please reference your SKU788-942or UPC
6940500313931.
4. Keep your receipt and these Instructions for Proof of Purchase.
TOOLS REQUIRED FOR ASSEMBLY & INSTALLATION
(not included):
5 Light Bulbs Safety goggles Ladder Gloves Wire strippers
(60 watt maximum)
(or CFL equivalent)
Flathead screwdriver Phillips screwdriver Electrical tape Wire cutters Pliers
Page 4
PARTS INCLUDED FOR ASSEMBLY (parts are not to scale):
1ea Canopy (#1) 1ea Screw Collar Loop (#2) 6 feet Chain (#3) 1ea Ring (#4)
1ea Loop (#5) 1ea Nipple (#6) 1ea Finial (#10) 5ea Socket Sleeves (#12)
1ea Column (#7)
5ea Shades (#13)
ASSEMBLY INSTRUCTIONS:
1. Carefully unpack the fixture. Lay out all parts on a clean surface. Evenly spread
the fixture arms to open the chandelier (see Fixture Distribution on Page 5).
2. Screw the Loop (#5) onto the Nipple (#6). Use pliers and a screwdriver to twist
open the link (cover the chain with cloth to prevent damage to the link finish) at
the end of the Chain (#3) not attached to the Screw Collar Loop (#2). To avoid
damage to the link, only open the link enough to hook it onto the Loop (#5).
Hook the open link to the Loop (#5) and then close the link.
3. Screw the Column (#7) onto Nipple A (#8). Screw the Finial (#10) onto Nipple
B (#9).
4. Weave the fixture wires up through the Loop (#5), through the Chain (#3),
through the Ring (#4), through the Screw Collar Loop (#2), through the Canopy
(#1), and through the Nipple (#20 on Page 7) on the Mounting Strap (#19 on
Page 7). Screw the Nipple (#20) into the Screw Collar Loop (#2).
5. Place the Socket Sleeves (#12) and then the Shades (#13) over the Sockets (#11).
6. Install five 60 watt candelabra incandescent light Bulbs (#14) (not included) or
five equivalent candelabra compact fluorescent light bulbs (not included) in the
five Sockets (#11).
Page is loading ...
Page 6
PARTS INCLUDED FOR INSTALLATION (parts are not to scale):
3ea Wire Connectors (#16) 1ea Ground Screw (#17) 1ea Hex Nut (#18)
1ea Mounting Strap (#19) 1ea Nipple (#20) 2ea Outlet Box Screws (#21)
INSTALLATION INSTRUCTIONS:
1. Screw the Nipple (#20) a half-inch into the Mounting Strap (#19). Tighten the Hex Nut (#18)
against the Mounting Strap (#19) to secure the Nipple (#20). Attach the Mounting Strap (#19)
to the Outlet Box (#15) using the two Outlet Box Screws (#21). [Make sure the longer end of
the Nipple (#20) is facing outside when the Mounting Strap (#19) is attached to the Outlet
Box (#15).]
2. Adjust the Chain (#3) to required height by using pliers and a screwdriver to twist open (cover
the chain with cloth to prevent damage to the link finish) the link of Chain (#3) attached to the
Loop (#5), lifting the fixture and attaching to a link closer to the ceiling. To avoid damage to
the link, only open the link enough to hook it onto another link. The fixture can be raised and
lowered in this manner until the desired height is achieved. Next, use pliers to twist open
(cover the chain with cloth to prevent damage to the link finish) the first unused link of Chain
(#3). Remove and save the excess chain. Pull the excess fixture wires through the Nipple (#20)
into the Outlet Box (#15). Wires may be left at full length or shortened as determined by space
in the Outlet Box (#15) to make the wire connections.
3. Wrap the ground wire from the fixture around the Ground Screw (#17) on the Mounting Strap
(#19), and then connect the ground wire from the fixture to the ground wire from the Outlet
Box (#15). Connect the wire without writing on it (with raised ribs) from the fixture to the
white wire (neutral wire) from the Outlet Box (#15). Connect the wire with writing on it from
the fixture to the black wire (live wire) from the Outlet Box (#15). Cover the three
connections using the three Wire Connectors (#16). Wrap the wire three connections with
electrical tape for a more secure connection. Position the wires back inside the Outlet Box
(#15). Note: If you have electrical questions, consult your local electrical code for approved
grounding methods.
4. Place the Canopy (#1) over the Nipple (#20) all the way to the ceiling. Tighten the Ring (#4)
onto the Screw Collar Loop (#2) until the Canopy (#1) is held firmly against the ceiling.
5. Installation is complete. Turn on the power at the circuit breaker or fuse box. Turn the light
switch on to activate the fixture.
Page is loading ...
Page 8
TROUBLESHOOTING:
PRODUCT MAINTENANCE:
1. To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean
water, never a solvent) to wipe the glass and surface of the fixture.
2. To clean the inside of the fixture, first disconnect power to the fixture by turning off the
circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly
dampened clean cloth (use clean water, never a solvent) to wipe the surface of the fixture.
3. Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry soft
cloth to dust or wipe carefully.
LIMITED WARRANTY
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period
of five (5) years from date of purchase. This warranty applies only to the original consumer purchaser and only
to products used in normal use and service. If this product is found to be defective, the manufacturer’s only
obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer’s
discretion, provided that the product has not been damaged through misuse, abuse, accident, modifications,
alterations, neglect or mishandling. This warranty shall not apply to any product that is found to have been
improperly installed, set-up, or used in any way not in accordance with the instructions supplied with the product.
This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence,
alteration, or faulty installation, or any other failure not relating to faulty material or workmanship. This
warranty shall not apply to the finish on any portion of the product, such as surface and/or weathering, as this is
considered normal wear and tear. The manufacturer does not warrant and specially disclaims any warranty,
whether express or implied, of fitness for a particular purpose, other than the warranty contained herein.
The manufacturer specifically disclaims any liability and shall not be liable for any consequential or
incidental loss or damage, including but not limited to any labor / expense costs involved in the
replacement or repair of said product.
Problem
Possible Cause
Corrective Action
Light Bulb will not
illuminate.
1. Light bulb is burned out.
1. Replace light bulb.
2. Power is off.
2. Make sure power supply
is on.
3. Faulty wire connection.
3. Check wiring.
4. Faulty switch.
4. Test or replace switch.
Fuse blows or circuit breaker
trips when light bulb is
illuminated.
Crossed wires or power wire
is grounding out.
Check wire connections.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page 17
MANUEL D'INSTRUCTIONS
Chandelier d'Intérieur 5LM
Collection Lucerne
The Home Depot UGS 788-942 (UPC 6940500313931)
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
