Commercial Electric WB0390 Operating instructions

Page 1

INSTRUCTION MANUAL

5LT Interior Chandelier

Home Depot SKU 334-549 (UPC 725916807085) (nutmeg)

Home Depot SKU 245-200 (UPC 6940500304175) (brushed nickel)

Page

2

Thank you for purchasing th

is Commercial Electric interior chandelier. This

product has been ma

nufactured with the highest standards of safety and

quality.

FEATURES:

1.

Five-light interior chandelier in nutmeg finish (SKU 334-549) or brushed

nickel finish (SKU 245-200) and frosted ribbed glass.

2.

Standard 72-inch wire and 48-inch chain for open entry-way and cathedral

ceiling installations.

3.

This fixture has been engineered to safely use up to five 60 watt medium

base incandescent light bulbs (do not exceed 60 watts each) (not included).

4.

For energy savings, this fixture has been engineered to safely use five

standard base compact fluorescent light bulbs (do not exceed 15 watts

each) (not included).

QUESTIONS, PROBLEMS, MISSING PARTS:

Before returning to your local

The Home Depot, please call our Customer

Service Team at 1

-877-527-0313 or visit www.homedepot.com. Please

reference your

SKU (334-549 nutmeg fixture, 245-200 brushed nickel fixture)

or

UPC (725916807085 nutmeg fixture, 6940500304175 brushed nickel

fixture

).

Page 3

CAUTION:

1.

Before starting installation of this fixture or removal of a previous fixture,

disconnect the power by turning off the circuit breaker or by removing the

fuse at the fuse box.

2.

CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY

ELECTRICAL QUESTIONS.

3.

If you have any non-electrical questions about this fixture, please contact

our Customer Service Team at 1-877-527-0313 or visit

www.homedepot.com. Please reference your SKU (334-549 nutmeg fixture,

245-200 brushed nickel fixture) or UPC (725916807085 nutmeg fixture,

6940500304175 brushed nickel fixture).

4.

Keep your receipt and these Instructions for Proof of Purchase.

TOOLS REQUIRED FOR ASSEMBLY & INSTALLATION

(not inc

luded):

5 Light Bulbs Safety goggles Ladder Gloves Wire strippers

(

60 watt maximum)

(

or CFL equivalent)

Flathead screwdriver Phillips screwdriver Electrical tape Wire cutters Pliers

Page

4

PARTS INCLUDED FOR ASSEMBLY (parts are not to scale):

1ea Canopy (#1) 1ea Screw 4 feet Chain (#3) 1ea Ring (#4)

Collar Loop (#2)

1ea Loop (#5) 1ea Nipple B (#7) 1ea Bottom Cover (#8) 1ea Finial (#9)

5ea Decorative Pans

(#11) 5ea Shades (#12) 5ea Socket Rings (#13)

ASSEMBLY INSTRUCTIONS:

1.

Carefully unpack the fixture. Lay out all parts on a clean surface.

2.

Screw the Loop (#5) onto Nipple A (#6). Use pliers and a screwdriver to twist

open the link (cover the chain with cloth to prevent damage to the link finish) at

the end of the Chain (#3) not attached to the Screw Collar Loop (#2). To avoid

damage to the link, only open the link enough to hook it onto the Loop (#5).

Hook the open link to the Loop (#5) and then close the link.

3.

Screw Nipple B (#7) onto the Bushing. Place the Bottom Cover (#8) over

Nipple B (#7), then screw the Finial (#9) onto Nipple B (#9) to secure the

Bottom Cover (#8).

4.

Weave the fixture wires up through the Loop (#5), through the Chain (#3),

through the Ring (#4), through the Screw Collar Loop (#2), through the Canopy

(#1), and through the Nipple (#21 on page 7) on the Mounting Strap (#19 on

page 7). Screw the Nipple (#21) into the Screw Collar Loop (#2).

5.

Unscrew the Socket Rings (#13) from the Sockets (#10). Place the Decorative

Pans (#11) on the Shades (#12). Place the Shades (#12) over the Sockets (#10).

Screw the Socket Rings (#13) on the Sockets (#10) to secure the Shades (#12).

6.

Install five 60 watt medium base incandescent light Bulbs (#14) (not included)

or five equivalent compact fluorescent light bulbs (not included) in the Sockets

(#10).

Page is loading ...

Page

6

PARTS INCLUDED FOR INSTALLATION (parts are not to scale):

3

ea Wire Connectors (#16) 1ea Ground Screw (#17) 1ea Hex Nut (#18)

1ea Mounting Strap (#19) 2ea Outlet Box Screws (#20) 1ea Nipple (#21)

INSTALLATION INSTRUCTIONS:

1.

Attach the Mounting Strap (#19) to the Outlet Box (#15) using the two Outlet Box Screws

(#20).

2.

Adjust the Chain (#3) to required height by using pliers and a screwdriver to twist open

(cover the chain with cloth to prevent damage to the link finish) the link of Chain (#3)

attached to the Loop (#5), lifting the fixture and attaching to a link closer to the ceiling. To

avoid damage to the link, only open the link enough to hook it onto another link. The

fixture can be raised and lowered in this manner until the desired height is achieved. Next,

use pliers to twist open (cover the chain with cloth to prevent damage to the link finish) the

first unused link of Chain (#3). Remove and save the excess chain. Pull the excess fixture

wires through the Nipple (#21) into the Outlet Box (#15). Wires may be left at full length

or shortened as determined by space in the Outlet Box (#15) to make the wire connections.

3.

Wrap the ground wire from the fixture around the Ground Screw (#17) on the Mounting

Strap (#19), and then connect the ground wire from the fixture to the ground wire from the

Outlet Box (#15). Connect the wire without writing on it (with raised ribs) from the fixture

to the white wire (neutral wire) from the Outlet Box (#15). Connect the wire with writing

on it from the fixture to the black wire (live wire) from the Outlet Box (#15). Cover the

connections using the Wire Connectors (#16). Wrap the wire connections with electrical

tape for a more secure connection. Position the wires back inside the Outlet Box (#15).

Note: If you have electrical questions, consult your local electrical code for approved

grounding methods.

4.

Place the Canopy (#1) over the Nipple (#21) all the way to the ceiling. Tighten the Ring

(#4) onto the Screw Collar Loop (#2) until the Canopy (#1) is held firmly against the

ceiling.

5. Installation is complete. Turn on the power at the circuit breaker or fuse box. Turn the light

switch on to activate the fixture.

Page is loading ...

Page

8

TROUBLESHOOTING:

PRODUCT MAINTENANCE:

1.

To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean

water, never a solvent) to wipe the glass and surface of the fixture.

2.

To clean the inside of the fixture, first disconnect power to the fixture by turning off the

circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly

dampened clean cloth (use clean water, never a solvent) to wipe the inside glass and

interior surface of the fixture.

3.

Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry soft

cloth to dust or wipe carefully.

LIMITED WARRANTY

The

manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period

of

five (5) years from date of purchase. This warranty applies only to the original consumer purchaser and only

to products used in normal use and service. If this product is found to be defective, the manufacturer’s only

obligation

, and your exclusive remedy, is the repair or replacement of the product at the manufacturer’s

discretion, provided that the product has not been damaged through misuse, abuse, accident, modifications,

alterations, neglect or mishandling. This warranty shall not apply to any product that

is found to have been

improperly installed, set

-up, or used in any way not in accordance with the instructions supplied with the product.

This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence,

alte

ration, or faulty installation, or any other failure not relating to faulty material or workmanship. This

warranty shall not apply to the finish on any portion of the product, such as surface and/or weathering, as this is

considered normal wear and tear.

The manufacturer does not warrant and specially disclaims any warranty,

whether express or implied, of fitness for a particular purpose, other than the warranty contained herein.

The manufacturer specifically disclaims any liability and shall not be liable

for any consequential or

incidental loss or damage, including but not limited to any labor / expense costs involved in the

replacement or repair of said product.

Problem Possible Cause Corrective Action

1. Light bulb is burned out. 1. Replace light bulb.

2. Power is off. 2. Make sure power

supply is on.

3. Faulty wire connection. 3. Check wiring.

Light Bulb will not

illuminate.

4. Faulty switch. 4. Test or replace switch.

Fuse blows or circuit

breaker trips when light

bulb is illuminated.

Crossed wires or power wire

is grounding out.

Check wire connections.

Page is loading ...

Commercial Electric WB0390 Operating instructions

Commercial Electric WB0390 Operating instructions

in other languages

Related papers

Other documents