LOWERY FIREPLACE
Parts List
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded
surface like carpet or blanket. Check that you have all parts indicated. Call customer service if hardware is missing.
Before beginning assembly, carefully study the diagrams below and sort your hardware according to the pictures.
Using the incorrect hardware will cause damage.
1 Quantity
of 1
Top panel
2 Quantity
of 1
Bottom panel
3L Quantity
of 1
Left side panel
3R Quantity
of 1
Right side panel
4L Quantity
of 1
Left Big Outside Pilaster
4R Quantity
of 1
Right Big Outside Pilaster
5 Quantity
of 1
Front Upper Panel
6 Quantity
of 1
Front Lower Panel
7L Quantity
of 1
Left Small Central Pilaster
7R Quantity
of 1
Right Small Central Pilaster
8 Quantity
of 1
Shelf Frame
9 Quantity
of 2
Wood Holder
10 Quantity
of 1
Firebox(sold in separate box)
A Quantity
of 22
Wood Dowel 5/16” x1-1/2”
B Quantity
of 22
Cam Bolt
C Quantity
of 22
Cam Lock
D Quantity
of 14
Screw∮5/32”x1”
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish. Avoid rubbing or scratching the
surface with rough or abrasive objects.
Call customer service at 1-800-633-5096
for assistance, questions, or Parts.
Assembly Tool Required No.2 Phillips
Screwdriver (Not Included)
Please do not over tighten cam bolts.
Please stop when you feel tight"
Figure 1
Insert cam locks (C) into holes on small
central pilasters (7L&7R) and front lower
panel ( 6 ).
Screw cam bolts (B) into holes on small
central pilasters (7L&7R) and front upper
panel ( 5 ).
.
Attach front upper panel(5) &small central
pilasters (7L&7R) and front lower panel
( 6 ) together by inserting wood dowels
(A) and cam bolts (B) into corresponding
holes until front upper panel(5) &small
central pilasters (7L&7R) and front lower
panel ( 6 ) meet.
Tighten by rotating cam locks (C)
clockwise with Phillips screwdriver.
Figure 2
Insert cam locks (C) into holes on left side
panels (3L).
Screw cam bolts (B) into holes on left big
outside pilasters (4L).
.
Attach left side panels (3L) to left big
outside pilasters (4L) by inserting wood
dowels (B) and cam bolts (A) into
corresponding holes until left side panels
(3L) and left big outside pilasters (4L)
meet.
Tighten by rotating cam locks (C)
clockwise with Phillips screwdriver.
Repeat the process to right side panels
(3R) and right big outside pilasters (4R)
Loring Entryway Storage Bench
Assembly Instructions
(2)
(1)
A
C
B
C
C
C
A
B
A
Figure 3
Insert cam locks (C) into holes on
pre-assembled unit from figure2.
Screw cam bolts (B) into holes on bottom
panel (2).
.
Attach pre-assembled unit from figure2
to bottom panel (2) by inserting wood
dowels (B) and cam bolts (A) into
corresponding holes until pre-assembled
unit from figure2 and bottom panel (2)
meet.
Tighten by rotating cam locks (C)
clockwise with Phillips screwdriver.
Figure 4
Insert one wood dowel (A) into the
hole on the bottom panel as shown.
Attach pre-assembled unit from figure 1
to pre-assembled unit from figure 3 with
screw (D) as shown.
Tighten them with Phillips head
screwdriver (not included).
Figure 5
.
Insert cam locks (C) into holes on
pre-assembled unit from figure4.
Screw cam bolts (B) into holes on top
panel (1).
.Attach pre-assembled unit from figure4
to top panel (1) by inserting wood dowels
(A) and cam bolts (B) into corresponding
holes until pre-assembled unit from
figure4 and top panel (1) meet.
Tighten by rotating cam locks (C)
clockwise with Phillips screwdriver.
Place the shelf frame (8) into the
bottom panel as the figure shown.
Figure 6
Place the fireplace instrument on the
right positions onto the shelf frame.
Hold the instrument from the back with
wood holder (9) and flat head scerw (D).
Make sure the flange of the instrument
traps into the groove of the wood holder.
Tighten the holders with phillips head
screwdriver (not included) as shown.
Figure 7
Now your fireplace is ready to use.
Please immediately examine this product carefully. Any request for missing parts or damage replacement
must be received within 90 days of your receipt of the product. Replacement, if available, will be honored
within this time frame. Parts will not be available for items arriving fully assembled. We do not recommend
modifying product(s) and we are not responsible for any damages due to product modification(s).
If
damages or missing parts are not reported within 90 days of your receipt, we are under no obligation to
provide parts or replacement merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri
Central time if you have product issues or email us at ser[email protected]. Please ask for customer service
representative for issues involving damages or replacement parts. Please ask for technical assistance
representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Parts Replacement Form
Customer Service 1-800-633-5096
service@seidal.com
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019
Page 4
Page11
/