Euroheat Harmony 45 Installation & Servicing Instructions Manual

PART NUMBER

SERIAL NUMBER

Installation &

Servicing Instructions

Harmony 35

Harmony 45

Balanced Flue Gas Stoves

IN1156 Edition E March 2012

2

Contents

Technical Data with Mertik Maxitrol GV34 Gas Valve 4

Accessories Supplied with Stove 6

Appliance Location 8

Installation of the Gas Supply 9

Flue Spigot Fitting 10

Installation of the Flue System 13

Installation of the Gas Log Effect 14

Placement of the Ember Glow Fibres 15

Fitting of the Gas Log Effect 15

Gas Connection 19

Gas Pressure Test Nipple Locations 21

Fitting the Remote Control 22

Information for Users Which Must be Advised by the Installer Verbally or in Writing 23

Spare Parts for Servicing H35 and H45 Gas Stoves 24

Changing Gas Operating Type 25

Primary Air Collar Adjustment 25

Servicing Instructions 26

Burner Removal and Replacement 27

Thermocouple Replacement 29

Door Handle Adjustment 31

Lower Door Opening and Level Adjustment 31

Balanced Flue Stove

Technical Guide

Document No: IN1105

When installing the stove this document should be used in

conjunction with the Euroheat Balanced Flue Technical Guide,

Document No: IN1105.

Information from the Euroheat Technical Team

Euroheat and Nestor Martin have a policy of continual research and development and reserve the right to

modify its appliances without prior notice. We make every effort to ensure that the information provided in

this document is correct and accurate at the time of printing. Continued updates occur to adapt documents to

customer requirements and appliance changes. For the latest editions of all Euroheat documentation visit our

web site www.euroheat.co.uk.

3

The Euroheat Appliance Serial Number

The serial number can be found at 5 locations:

1: On the front page of this manual.

2: On the front page of the operating instructions.

3: On the identiﬁcation plate located below the gas valve.

4: On the registration form.

5: On the registration certiﬁcate returned to the user after successful registration.

Safety Precautions

a) The stove should be visually inspected and if damaged should not be installed.

b) It is a requirement of the Gas Safety (Installation and Use) Regulations that these instructions,

together with the Appliance User Instructions, be left intact with the user.

c) In your own interest, and those of safety, and in accordance with the Gas Safety (Installation

and Use) Regulations, Euroheat stoves must be installed by a suitably qualiﬁed Gas Safe

technician using the appropriate ﬁttings for the gas type being used, and the stove must not

be modiﬁed in anyway. The gas technician will be responsible for the installation conforming

to all current regulations and standards, during the life of this publication these standards may

be superceded and it is the installer’s responsibility to ensure the installation conforms to

whatever standards are current at the time of installation. Failure to install the appliance

correctly could lead to prosecution.

BS 1251 : 1987 Fireplace Components

BS 5871 : PT 1 2005 Installation of Gas Fires

BS 5482 : PT 1 1994 LPG Installations

BS 6891 : 1998 Pipe Work Installation

d) It is important to ensure that the ﬂue system on which the appliance is to be installed is

ﬁtted in accordance to Euroheat’s Balanced Flue Technical Guide, Document No: IN1105.

It is therefore important, in the interests of safety, that these instructions are strictly followed,

together with the legal Statutes and Codes of Practice, current at the time of installation.

e) It is important that the stove is installed so that the clearances speciﬁed in these instructions are

complied with.

f) The stove must NOT be run with its door open.

g) It is also important that the occupiers of the property have their attention drawn to the high

temperatures which are normally present on the external surfaces of the stove during operation.

h) Fireguards, in accordance with current British Standards, should be ﬁtted when the appliance is

in the presence of young children, the elderly or inﬁrm.

i) Do not use the stove if any of the ceramic log or coal effect components are damaged or broken

during transportation. Check all gas joints within the stove for gas tightness as vibration during

transportation may loosen them.

j) Ensure that all transport packaging is removed from inside and outside of the stove.

k) The plastic bags used to protect components of this appliance are a potential hazard to young

children, and should be disposed of immediately.

l) The stove must be serviced annually by a suitably qualiﬁed Gas Safe technician.

Manufacturers Identiﬁcation Plate

The identiﬁcation plate is located below

the gas valve. To access the plate swing

outwards.

4

Model Number

H35 H35001 Cast Black,

H35002 Bottle Green Enamel,

H35003 Satin Black Enamel

Standard supply appliance is conﬁgured for Natural Gas; for LPG specify at time of order

Heat Output Maximum

G20 Natural Gas 7.5kW

G31 Propane 7.1kW

Gas Input Maximum

G20 Natural Gas 8.7kW

G31 Propane 8.2kW

Net Efﬁciency Nat. Gas & LPG 86%

Air Collar Adjustment

Natural Gas 4mm

LPG Maximum

Free Air Requirement NIL

Fuel Effect Type Ceramic burner, ceramic logs, ceramic cubes,

ember glow ﬁbres.

Heat Control Manual with remote control option

Ignition Type Piezo

Pilot Flame Yes

Flame Failure Yes

Fuel Outlet Options Top or Rear

Flue Size 180mm (7”) External Diameter

Warranty Standard 1 Year

Seasonal Efﬁciency

The efﬁciency of this appliance has been measured as speciﬁed in BS EN 613:2001 and the result is 77.9% Nat.

Gas and 80.2% LPG. The gross caloriﬁc value of the fuel has been used for this efﬁciency calculation, the Net

efﬁciency being 86% Nat. Gas and 86% LPG. The test data from which it has been calculated has been certiﬁed

by BELTEST. The efﬁciency value may be used in the Governments Standard Assessment Procedure (SAP) for

energy rating of dwellings.

Technical Data for Harmony 35 (H35) with Mertik Maxitrol GV34 Gas

Valve.

Gas

Type

Gas

Pressure

mbar

Main Jet

mm

Pilot

Jet

Maximum Output

Control Set to Maximum

Minimum Output

Control Set to Minimum

Hourly

Flow

High

Burner

Pressure

Net

Efﬁciency

%

Hourly

Flow

Low Burner

Pressure

G20

Natural

Gas

20

1 jet

with

4 x 1.18

27.2 0.91m3/h 18.1 mbar 86.1

0.65

m3/h

8.9 mbar

G31

LPG

37

1 jet

with

4 x 0.78

22.1

0.33

m3/h

36.1 mbar 86.9

0.25

m3/h

21.2 mbar

5

Model Number

H45 H45002 Cast Black,

H45004 Green Enamel

H45003 Satin Black Enamel

Standard supply appliance is conﬁgured for Natural Gas; for LPG specify at time of order

Heat Output Maximum

G20 Natural Gas 8.90kW

G31 Propane 9.78kW

Gas Input Maximum

G20 Natural Gas 10.27kW

G31Propane 11.19kW

Net Efﬁciency Nat. Gas & LPG 87%

Air Collar Adjustment

Natural Gas Maximum

LPG Maximum

Free Air Requirement NIL

Fuel Effect Type Ceramic burner with ceramic logs, ceramic cubes,

ember glow ﬁbres.

Heat Control Manual with remote control option

Ignition Type Piezo

Pilot Flame Yes

Flame Failure Yes

Fuel Outlet Options Top or Rear (Top pre ﬁtted)

Flue Size 180mm (7”) External Diameter

Warranty Standard 1 Year

Seasonal Efﬁciency

The efﬁciency of this appliance has been measured as speciﬁed in BS EN 613:2001 and the result is 78% Nat.

Gas and 80.7% LPG. The gross caloriﬁc value of the fuel has been used for this efﬁciency calculation, the Net

efﬁciency being 87% Nat. Gas and 87% LPG. The test data from which it has been calculated has been certiﬁed

by BELTEST. The efﬁciency value may be used in the Governments Standard Assessment Procedure (SAP) for

energy rating of dwellings.

Gas

Type

Gas

Pressure

mbar

Main Jet

mm

Pilot

Jet

Maximum Output

Control Set to Maximum

Minimum Output

Control Set to Minimum

Hourly

Flow

High

Burner

Pressure

Net

Efﬁciency

%

Hourly

Flow

Low Burner

Pressure

G20

Natural

Gas

20

1 jet

with

4 x 1.29

27.2

1.09

m3/h

18.4 mbar 86.7

0..84

m3/h

10.8 mbar

G31

LPG

37

1 jet

with

4 x 0.87

22.1

0.46

m3/h

36.5 mbar 87.4

0.31

m3/h

16.9 mbar

Technical Data for Harmony 45 (H45) with Mertik Maxitrol GV34 Gas

Valve.

MAX

E & OE Instructions Part number IN1156 Ed. E

6

Flue Spigot (Collar) and Choke Plate

The ﬂue spigot (collar), inner ﬂue pipe

and choke plate may be found either

screwed to the pallet on which the

stove is delivered, within the body of

the stove, or ﬁtted to the stove.

Elbow for Gas Fitting

Accessories Supplied with Stove

Supplied with the balanced ﬂued gas stoves are a number of installation accessories and instruction manuals.

Nut

Olive

Elbow

Foot Levelling Screws and

Triangular Hearth Protectors

In the plastic bag within the stove there will be 4 foot

levelling grub screws and 4 plastic triangular hearth

protectors. The grub screws should be ﬁtted to the feet

prior to installation to allow for levelling the stove on

an uneven hearth.

The plastic hearth protectors can be put under the

feet to protect the hearth when sliding the stove into

position, but should be removed unless required to

help level the stove.

Enamel Repair Touch Up

(Enamel Stoves Only)

In the plastic bag within the stove there

will be a bottle or tube of enamel touch

up which will match the enamel ﬁnish

on the stove. This can be used to repair

any minor chips on the enamel surface

of the stove.

Grub Screw

Plastic Hearth Protector

EMBERGLOW

Platinum

Bright

Embers

Ember Glow

Small squares of platinum

embers which when teased

out give an ash effect with

the ceramic log or coal effect

(see page 14).

Flue Spigot (collar)

Inner Flue Pipe

Choke Plate

Glove

A heat proof glove is also supplied

with the stove. This is for use by the

installing and servicing engineer if

they have to open the main ﬁrebox

door when hot.

7

Installation Instructions and Balanced Flue

Technical Guide IN1105

For the use of the suitably qualiﬁed engineer for the

installation and servicing of the stove.

MUST be handed to the owner of the stove.

Operating Instructions

For the use of the person for the safe operation of the

stove.

MUST be handed to the owner of the stove.

If there are any of the above documents missing from your stove

upon delivery please contact Euroheat with the serial number of the

stove and we will immediately despatch a replacement.

Balanced Flue Stove

Technical Guide

Document No: IN1105

Fraxﬁll (MS9045)

Fraxﬁll is a pliable white ceramic ﬁbre gap ﬁll and

should be used for sealing all the ﬂue joints. It is

supplied for use with a sealant gun. It is odourless

and recommended for applications with operating

temperatures of 1200°C.

PART NUMBER

SERIAL NUMBER

Installation &

Servicing Instructions

Harmony 35

Harmony 45

Balanced Flue Gas Stoves

IN1156 Edition E June 2009

PART NUMBER

SERIAL NUMBER

Operating Instructions

Harmony

Stanford

Conventional Flue & Balanced Flue

Gas Stoves

IN1123 Edition G June 2009

H35 Burner Brackets

The two burner brackets are ﬁtted inside the ﬁre box

on the left and right inner walls. They are used to

locate the ceramic burner in place. They are supplied

with 2 self tapping screws.

GAS STOVE REGISTRATION

Please complete the form on pages 3 and 4 and return it with a

copy of your sales receipt from your Euroheat approved supplier

to obtain your

THREE GOOD REASONS

Why you should have your stove commissioned.

It is vital for the longevity and efﬁcient and safe operation of the stove to have the stove installed and

commissioned by a competent qualiﬁed heating engineer.

1. Installation

The stove should be installed by a competent qualiﬁed heating engineer, who will be conversant with the

Building Regulations and Codes of Practice current at the time of installation. Installation instructions are

supplied with the stove which contain instructions speciﬁc to the appliance.

Incorrect installation may lead to poor performance of the stove and ultimately damage to the appliance.

2. Operating

The operation of the stove should be demonstrated by a competent person, so you, as the operator, are

conversant with the operation of the controls. Instructions on the use of the controls can be found in the

operating instructions supplied with the stove.

Incorrect operation of the controls of the stove may lead to poor performance from the stove and ultimately

damage the appliance.

3. Maintenance

Routine maintenance as described in the operating instructions, supplied with the stove, should be

undertaken by a competent person.

Failure to perform the routine maintenance may adversely effect the performance of the stove and

ultimately damage the appliance.

Registration Form

To be completed by both the owner of the stove and the installing/

commissioning engineer.

It MUST be returned to Euroheat for the registration to be completed.

8

Hearth and Fireplace Requirements

Do not be tempted to ﬁt the stove into an unsuitable ﬁreplace. Beyond the requirements

of the building regulations and access to facilitate servicing the stove, providing a

setting which will complement the stove is not a luxury, it is the practicality of making

the most of an investment. A good builder will be able to transform even the most

utilitarian of ﬁreplaces, whether altering its proportions to those of the “Golden Mean”

ideal, exposing a wooden lintel, stone or simply removing superﬂuous detailing for

comparatively small costs, and the result will be a pleasure for many years.

Minimum clearance

from combustible

materials

Minimum clearance

from non

combustible

materials

A 12" 300mm** 9" 230mm

B 6" 150mm** 4" 100mm

C 1" 25mm** N/A

D 2" 50mm** 2" 50mm

E 6" 150mm** 4" 100mm

F

12mm of non

combustable material.

12mm of non

combustable material.

Curtains and furnishings should be a minimum of

1m from the stove.

The stove can be placed on a combustible

ﬂoor providing it can support the weight,

and providing a non combustible hearth

plinth with a minimum thickness of

12mm is utilized.

** The measurements provided are

for guidance only.

In all installations any surrounding

ﬂammable materials must not be allowed

to exceed 80°C or a non combustible

shield provided in accordance with

current regulations. The stove must

always stand perfectly level and have

sufﬁcient space allowing for service

work.

A

B

D

C

E

F

1/3 2/3

“Golden Mean”

Side Proﬁle

1

2/3

“Golden Mean”

Front View

9

Appliance Location

a) This stove must be mounted on a non combustible hearth. The hearth must have a minimum of

12mm non combustible material thickness. The stove can be placed on a wooden ﬂoor if it can

support the weight and as long as the hearth plinth is utilized.

b) Combustible material at the rear of the stove shall be protected against the effects of heat.

c) There must be a minimum of 300mm from the top of the stove to the underside of any combustible

shelf. Note that for every 50mm increase on clearance, the shelf may project by a further 50mm.

d) The appliance, being room sealed, may be installed in a room or space which will be used by the

occupants for sleeping.

e) Any manufactured surround used with this stove should comply with the appropriate British Standard.

f) Do not place furniture, furnishing or combustible objects within 1 metre of the stove.

If any of these conditions are not fulﬁlled,

DO NOT FIT THE STOVE until this has been rectiﬁed.

Installation of the Gas Supply

BS 6891

NOTE:

Ensure that the gas supply is capable of delivering the required amount of gas, and is in accordance with

the relevant current standards.

It is generally preferred to conceal the gas supply by bringing it under the hearth, or through masonry to the

side of the ﬁreplace. Any pipe work in 8mm tube connecting the stove to the main pipe work should be kept

as short as possible with as few ﬁttings as possible to prevent restrictions.

a) Whenever a gas pipe passes through any masonry it must have a sleeve of non combustible material

sealed at both ends to prevent the gas supply from coming in contact with masonry or lime based

mortars.

b) The gas pipe should be adequately supported over longer lengths.

c) Soft copper tubing and soft soldered joints are suitable, providing the tube is not closer than 150mm

to the stove casing i.e. the temperature must not exceed 100°C.

d) A means of isolating the gas supply to the appliance must be provided independent of any appliance

control. This may be a gas cock, ideally of the nursery type to prevent children interfering with the

gas supply.

e) Any gas tubing that has been passed through masonry, should be purged to expel any foreign

materials that may have entered the supply.

f) Care should be taken to ensure that pipe work brought through metal structures has been secured to

prevent chafﬁng, but allow for thermal expansion.

10

Flue Spigot Fitting

The ﬂue can be either top or rear exit. The ﬂue collar (spigot) is supplied attached to the pallet on which the

stove is delivered or within the body of the stove. It will need ﬁtting to the stove depending on which ﬂue kit

you are using, rear exit can only be used on the rear to horizontal low-level ﬂue kit.

Fitting Top Flue Spigot

The stove comes with the inner top ﬂue pipe adapter ﬁtted to the stove with a choke plate ﬁtted below it, see

picture below. Ensure that the choke plate ﬁtted is correct for the gas type and ﬂue conﬁguration to be installed,

this information is in the Balanced Flue Stove Technical Guide: IN1105. If not replace with the correct choke

plate which can be found in the bag of installation accessories.

Inside the stove in the bag of installation accessories will be the ﬂue spigot gasket and two M5 screws to ﬁt the

cast iron spigot. Fit the gasket as shown above and then attach the ﬂue spigot using the two screws.

Fitting Flue Spigot and Inner Adapter Pipe

to the Rear of the Stove.

1) Remove the inner adapter pipe, see above, and

choke plate from the top of the stove. The choke

plate is not required for the rear ﬂue option.

Choke plate

Ceramic gasket

Inner ﬂue pipe

adapter

Choke plate

11

2) Remove the cast iron blanking plate from the rear of the stove.

3) Loosen the four screws on the inner steel blanking plate on the rear of the stove. Twist the blanking

plate so that the plate lifts over the screws.

4) Align the inner ﬂue adapter pipe with the screws and twist it so it locks into position. Tighten the four

screws to ensure a good seal.

NOTE:

Do not ﬁt the choke plate to the rear outlet as it will

restrict the air ﬂow and stall the ﬂue gasses and the

stove will not work.

12

5) Fit the spigot gasket and ﬂue spigot to the rear of the stove.

6) Fit the rear inner blanking plate to the top of the stove, see picture below. The stove will not run if this

part is omitted.

7) Fit the gasket and rear blanking plate onto the top ﬂue exit using the countersunkscrews. If it has an

enamel ﬁnish the cup washers should also be used to protect the enamel ﬁnish.

Cup washer for

enamelled ﬁnished

stoves

13

Installation of the Flue System

All the information regarding the three types of ﬂue kits can be found in the Euroheat’s Balanced Flue Technical

Guide, Document No: IN1105.

IMPORTANT

To the Installer, Please Read Prior to Installation

There have been a number of reports of stoves giving

off an unpleasent smell after the curing process has

ﬁnished. In most cases it has been found that some

form of Mastik has been used to join the ﬂue pipes

together and to the ﬂue spigot (collar) on the stove.

Some of these so called “Heat Proof” mastiks will only

stand a temperature of 300°C before they start breaking

down. In many cases they may give off an obnoxious

smell at temperatures much lower than this.

Please ensure that the jointing compound used is

suitable, if in doubt contact the manufacturer of the

sealing compound before you use it.

We would advise the use of Fraxﬁll on all ﬂue joints and

for all fuel types, available from your Euroheat dealer

or directly from Euroheat.

Fraxﬁll 300g cartridge. Part No: MS9045

Top to Horizontal High-level

Flue Kit: MS91103

Top to Vertical High-level

Flue Kit: MS91101

Rear to Horizontal Low-level

Flue Kit: MS91098

14

Installation of the Gas Log Effect

If any of the components of the log effect or burner are broken DO NOT INSTALL. Contact your stove supplier

for replacements. The log effect kit is not covered by the stoves warranty for accidental damage, so great

care should be taken when handling the ceramic burner and logs. It is important that the logs, ember glow

ﬁbres and ember cubes are installed in accordance with these instructions as any deviation may cause poor

combustion. The addition of further ceramic logs or cubes is strictly prohibited.

Back log

Left log

Front log

Ceramic burner

Burner and Log Set Components

Ember cubes

1 gram bag ember

glow ﬁbres

Burner and Log Assembly Complete

EMBERGLOW

Platinum

Bright

Embers

15

Do not cover pilot

ignition route holes

with either ember

cubes or ember ﬁbres.

Place ﬁbres and cubes

to the side of this

area.

Pilot Ignition Route

Do not compress the embers or force into

position.

Placement of the Ember Glow Fibres

Platinum ember glow ﬁbres are for use in vented gas appliances only. Platinum ember glow ﬁbres are made from

high grade ceramic wool. The wool is similar to ﬁbreglass and should be handled carefully. We recommend the

use of suitable dust mask, gloves or tweezers when placing the embers in position. Wash hands immediately

after touching to avoid irritation. Do not store the embers close to ﬂammable liquids.

The embers must be placed correctly in order

to function properly. Tease out the fabric to

form loose, irregular shapes.

Use of Embers

With the embers correctly placed they glow and ﬂicker similar to glowing ash. Their placement is important as

the effect produced can only occur when they are heated by the gas jets or by direct radiated heat. Once the

burner has been lit the embers may need adjusting to give the required effect.

The pack containing the ember glow ﬁbres contains more than is required.

The additional embers should be kept for further service requirements.

Important:

tease out fabric to form

loose, irregular shapes.

16

Fitting the Log Effect Kit

This is very fragile and should be handled with the utmost care. Ensure that all transport packaging which held

the ceramic burner in place in transit has been removed.

Position the main log at the rear of the burner, so that the ﬂat surfaces of the rear log and burner sit

together.

1. Place ceramic cubes adjacent to the holes of the burner underneath the rear log with teased out sections

of ember glow under each ember cube, leaving about 5mm between each cube. Do not place ceramic cubes or

ember glow on the pilot ignition route (see previous page). Gently rub the ember glow into the burnt surfaces

of the log.

2. Fit the left hand log with the larger end on the burner and the smaller end against the rear log. There is

a small groove next to the left circular secondary air hole. The left log has a chamfered edge which should be

located into this groove. Gently rub the ember glow into the burnt surfaces of the log.

Left log ﬁts into groove in

burner surface

17

3. Fit the front log. In the centre of the burner is a groove for the front log to be located. Gently rub ember

glow into the burnt surfaces of the log.

Place ceramic ember cubes along the holes of the burner in front of and to the sides of the right hand log, with

teased out sections of ember glow under each ember cube, leaving about 5mm between each cube.

18

4. Place the front log in the front locating slot in the burner surface, then lean the log against the left log.

The ceramic cubes may have to be adjusted to allow the front log to sit correctly.

The ceramic log effect burner should NOT be used if damaged in anyway.

Do not be tempted to try to mend the ceramic log effect burner, always replace it.

The ceramic log effect burner sits lightly on top of the gas input venturi tube, do not push the burner

hard down onto it as this may crack the ceramic log effect burner.

When the appliance is ﬁrst ﬁred small adjustments to the ceramic cubes and ember glow can be made to

achieve the desired effect.

19

Gas Connection

Harmony 45 (H45)

Connect a 15mm gas supply pipe to the 3/8” connection at the rear of the appliance. We advise that a

minimum supply pipe size of 15mm is utilized, (8-10mm supply pipe is not suitable).

Harmony 35 (H35)

Bring a 15mm gas supply pipe as close as possible to the appliance connection, use an 8mm pipe for the ﬁnal

connection. Do not use more than 500mm of 8mm ﬁnal connecting pipe.

Connect a suitable gas pressure gauge to the test nipple on the gas valve, see page 18, turn the gas supply on

and check that the gas connections are sound. If satisfactory light the appliance. Check all the gas connections

on the appliance for leaks. The appliance is factory tested, but it is possible for a connection to have been

disturbed during transportation and installation.

Set the control to the high setting, and check that the gas pressure is as stated on the data table.

Turn off the gas, remove the pressure gauge and reﬁt the test point screw, turn the gas supply on and check

that the test nipple is gas sound.

Lighting

For full operating instructions see operation manual.

Turn the on/off knob, smaller right hand knob, slightly counter-clockwise towards the ignition position until the

control knob stops turning, press it down and hold for 5 seconds to allow the gas to the pilot light.

After 5 seconds turn the control to the pilot position with the knob still depressed. There will be an audible click

as the Piezo spark is generated. Hold down the control knob for 30 seconds if the pilot has lit, if it has not lit

then repeat the pilot lighting procedure to maximum of 6 attempts. If after 6 attempts the pilot has not ignited

leave the appliance for 5 minutes before attempting again. (This assumes the system has been purged)

Once the pilot has been established, let out the control knob and turn it anticlockwise to the “ON” position.

Main Burner Control

Turn the larger left hand control anti clockwise to increase, clockwise to decrease the desired heat output.

Burner output control.

The main burner control will set the output from the

burner, from maximum to minimum and to off.

Mertik Maxitrol GV34 Gas Valve

On/Off

Pilot Setting and

Ignition Control

20

Insert a small screwdriver

into slot, lever downwards and

lift cover off

On/Off

Pilot Setting and

Ignition Control

Manual Control

Front cover screw

Mertik Maxitrol GV34 Gas Valve

Removing Gas valve Cover Plate

Pilot gas and pressure regulator adjustment screws are located under the cover. To remove the cover, ﬁrst

loosen the screw next to the temperature knob.

Insert the tip of a small screwdriver into the slot on the top of the front cover next to the on/off knob, push

downwards and lift the cover off.

_

+

Pilot flame

adjustment screw

(preset at factory)

Operating pressure

adjustment screw

(The direction is indicated on

the brass cover of the

adjustment screw)

Low pressure adjusting screw

(The flat blade screw can be accessed

to the right hand side, anti clockwise to

increase, clockwise to decrease.)

Page is loading ...

Euroheat Harmony 45, Harmony 35 Installation & Servicing Instructions Manual

Related papers

Other documents