Sanyo Xacti VPC-A5 User manual

Brand: Sanyo

Model: Xacti VPC-A5

Type: User manual

This manual is also suitable for

Xacti VPC-A5EX

SERVICE MANUAL

Digital Camera

VPC-A5

VPC-A5EX

(Product Code : 126 694 00)

(Korea)

(Taiwan)

(Product Code : 126 694 01)

(Europe)

(Asia)

Contents

1. OUTLINE OF CIRCUIT DESCRIPTION .................... 2

2. DISASSEMBLY ........................................................ 10

3. ELECTRICAL ADJUSTMENT .................................. 14

4. USB STORAGE INFORMATION

REGISTRATION ...................................................... 19

5. TROUBLESHOOTING GUIDE................................. 20

6. PARTS LIST............................................................. 22

CABINET AND CHASSIS PARTS 1 ........................ 22

CABINET AND CHASSIS PARTS 2 ........................ 24

ELECTRICAL PARTS .............................................. 26

PACKING MATERIALS............................................ 30

ACCESSORIES ....................................................... 30

CIRCUIT DIAGRAMS &

PRINTED WIRING BOARDS ...................................... C1

The components designated by a symbol ( ! ) in this schematic diagram designates components whose value are of

special significance to product safety. Should any component designated by a symbol need to be replaced, use only the part

designated in the Parts List. Do not deviate from the resistance, wattage, and voltage ratings shown.

CAUTION : Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer.

Discard used batteries according to the manufacturer’s instructions.

NOTE : 1. Parts order must contain model number, part number, and description.

2. Substitute parts may be supplied as the service parts.

3. N. S. P. : Not available as service parts.

Design and specification are subject to change without notice.

SX71A/U, EX

REFERENCE No. SM5310603

FILE NO.

PRODUCT SAFETY NOTICE

– 2 –

Pin No.

Symbol Pin Description

Waveform

Voltag e

Table 1-1. CCD Pin Description

When sensor read-out

Fig. 1-1. CCD Block Diagram

1. OUTLINE OF CIRCUIT DESCRIPTION

1-1. CA1 CIRCUIT DESCRIPTION

1. IC Configuration

IC903 (MN39620PJJ-A) CCD imager

IC901 (AN20101A) V driver

IC905 H driver, CDS, AGC, A/D converter

2. IC903 (CCD imager)

[Structure]

Interline type CCD image sensor

Image size Diagonal 6.67 mm (1/2.7 type)

Pixels in total 2690 (H) x 1994 (V)

Effective pixels 2576 (H) x 1925 (V)

4, 7, 8

5, 6

9, 13

VØV3B,

VØV3A

VØV4, VØV2,

VØV1

Vertical register transfer clock

Signal output

-6.0 V, 0 V, 12 V

Aprox. 6 V

Vertical register transfer clock

VØV

GND

0 V

-6.0 V, 0 V

VØRG

Circuit power

Reset gate clock

GND

2 V, 6 V

12 V

VOD

VPT

Protection transistor bias

Substrate clock

DCVSUB

-6.0 V

VØH

Horizontal register transfer clock

0 V, 3.3 V

2, 3

VØV5B,

VØV5A

Vertical register transfer clock

Aprox. 0 V

(Different from every CCD)

-6.0 V, 0 V, 12 V

Aprox. 6 V

VØH2

Horizontal register transfer clock18

0 V, 3.3 V

Substrate voltage bias

SUBSW

VøRG

VøH1

VøH2

: Photo diode

Output part

VPT

SUBSW

VøV3A

Vertical shift register

Horizontal shift register

VøV3B

VøV4

VøV5A

VøV5B

VøV6

VøV1

VøV2

VSUB

– 3 –

3. IC901 (V Driver)

V driver is necessary in order to generate the clocks (vertical

transfer clock, horizontal transfer clock and electronic shutter

clock) which driver the CCD.

IC901 is a V driver. The clock which is output from IC101 is

added inside V driver, and gererated clock neccesary in or-

der to read data from IC903.

XSUB signal which is output from IC101 is the sweep pulse

for electric shutter.

4. IC905 (CDS, AGC, A/D Converter and H Driver)

The video signal which is output from the CCD is input to Pin

(29) of IC905. There are inside the sampling hold block, AGC

block and A/D converter block.

The setting of sampling phase and AGC amplifier is carried

out by serial data at Pin (32).The video signal is carried out

A/D converter, and is output by 12-bit. A H driver is inside

IC905, and H1, H2 and RG clock are generated at IC905.

Fig. 1-2. IC905 Block Diagram

CCDIN

H1-H4

SDATA

SCK

CLI

CLPOB

CLPDM

DOUT

VRB

VRT

PRECISION

TIMING

CORE

SYNC

GENERATOR

PxGA

VGA

ADC

2~36 dB

PBLK

VREF

CLAMP

INTERNAL

REGISTERS

INTERNAL

CLOCKS

CDS

CLAMP

HORIZONTAL

DRIVERS

– 4 –

1-2. CP1 CIRCUIT DESCRIPTION

1. Circuit Description

1-1. Digital clamp

The optical black section of the CCD extracts averaged val-

ues from the subsequent data to make the black level of the

CCD output data uniform for each line. The optical black sec-

tion of the CCD averaged value for each line is taken as the

sum of the value for the previous line multiplied by the coeffi-

cient k and the value for the current line multiplied by the

coefficient 1-k.

1-2. Signal processor

1. γ correction circuit

This circuit performs (gamma) correction in order to maintain

a linear relationship between the light input to the camera

and the light output from the picture screen.

2. Color generation circuit

This circuit converts the CCD data into RGB signals.

3. Matrix circuit

This circuit generates the Y signals, R-Y signals and B-Y sig-

nals from the RGB signals.

4. Horizontal and vertical aperture circuit

This circuit is used gemerate the aperture signal.

1-3. AE/AWB and AF computing circuit

The AE/AWB carries out computation based on a 64-segment

screen, and the AF carries out computations based on a 6-

segment screen.

1-4. SDRAM controller

This circuit outputs address, RAS, CAS and AS data for con-

trolling the SDRAM. It also refreshes the SDRAM.

1-5. Communication control

1. SIO

This is the interface for the 8-bit microprocessor.

2. PIO/PWM/SIO for LCD

8-bit parallel input and output makes it possible to switch be-

tween individual input/output and PWM input/output.

1-6. TG/SG

Timing generated for 5 million pixel CCD control.

1-7. Digital encorder

It generates chroma signal from color difference signal.

2. Outline of Operation

When the shutter opens, the reset signals (ASIC and CPU)

and the serial signals (“take a picture” commands) from the

8-bit microprocessor are input and operation starts. When the

TG/SG drives the CCD, picture data passes through the A/D

and CDS, and is then input to the ASIC as 12-bit data. The

AF, AE, AWB, shutter, and AGC value are computed from this

data, and three exposures are made to obtain the optimum

picture.

The data which has already been stored in the SDRAM is

read by the CPU and color generation is carried out. Each

pixel is interpolated from the surrounding data as being ei-

ther R, G, and B primary color data to produce R, G and B

data. At this time, correction of the lens distortion which is a

characteristic of wide-angle lenses is carried out. After AWB

and γ processing are carried out, a matrix is generated and

aperture correction is carried out for the Y signal, and the

data is then compressed by JPEG and is then written to card

memory (SD card).

When the data is to be output to an external device, it is taken

data from the memory and output via the USART. When played

back on the LCD and monitor, data is transferred from memery

to the SDRAM, and the image is then elongated so that it is

displayed over the SDRAM display area.

3. LCD Block

The LCD display circuit is located on the CP1 board, and

consists of components such as a power circuit.

The signals from the ASIC are 8-bit digital signals, that is

input to the LCD directly. The 8-bit digital signals are con-

verted to RGB signals inside the LCD driver circuit . This LCD

has a 3-wire serial, and functions such as the brightness and

image quality are controlled.

Because the LCD closes more as the difference in potential

between the VCOM (common polar voltage: AC) and the R,

G and B signals becomes greater, the display becomes darker;

if the difference in potential is smaller, the element opens and

the LCD become brighter.

In addition, the timing pulses for signals other than the video

signals are also input from the ASIC directory to the LCD.

4. Lens drive block

4-1. Focus drive

The focus stepping motor drive signals (FIN1, FIN2, FIN3, and

FIN4) which are output from ASIC (IC101) are used to drive

by the motor driver (IC951). Detection of the standard focus-

ing positions is carried out by means of the photointerruptor

(FOCUS PI) inside the lens block.

4-2. Zoom drive

The zoom stepping motor drive signals (ZIN1, ZIN2, ZIN3 and

ZIN4) which are output from ASIC (IC101) are used to drive by

the motor driver (IC951). Detection of the standard zoom posi-

tions is carried out by means of photointerruptor (ZOOM PI)

inside the lens block.

4-3. Iris drive

The iris motor drive signals (IIN1 and IIN2) which are output

from the ASIC (IC101) are converted into regular current drive

by the motor driver (IC951), and are then used to drive the iris

steps.

4-4. Shutter drive

The shutter motor drive signals (SIN1, SIN2) which are output

from the ASIC (IC101) are converted into regular current drive

by the motor drive (IC951), and the mecha shutter is opened

and closed.

– 5 –

1-3. PWA POWER CIRCUIT DESCRIPTION

1. Outline

This is the main power circuit, and is comprised of the follow-

ing blocks.

Switching power controller (IC501)

Input voltage 5.8 V to CH2, CH3 and CH4 (Q5002, L5001)

Digital 3.25 V system power output (L5002)

Digital 1.7 V system power output (L5003)

Analog 3.45 V system power output (L5004)

Analog system power output (T5001)

LCD system power output (L5008)

LCD backlight system power output (L5009)

2. Switching Controller

This is the basic circuit which is necessary for controlling the

power supply for a PWM-type switching regulator, and is pro-

vided with seven built-in channels, only CH1 (input voltage

5.8 V to CH2, CH3 and CH4), CH2 (digital 3.25 V system

power output), CH3 (digital 1.7 V system power output), CH4

(analog 3.45 V system power output), CH5 (analog system

power output) CH6 (LCD system power output) and CH7 (LCD

backlight system power output) are used. Feedback from in-

put voltage 5.8 V to CH2, CH3 and CH4 (CH1), VDD3 (CH2),

VDD1.8 (CH3), +3.45 V (A) (CH4), +12 V (A) (CH5), LCD 12

V (CH6) and LED backlight constant current output (CH7)

power supply outputs are received, and the PWM duty is var-

ied so that each one is maintained at the correct voltage set-

ting level.

2-1. Short-circuit Protection

If output is short-circuited for the length of time determined

by the condenser which is connected to Pin (9) of IC501, all

output is turned off. The control signal (P ON) are recontrolled

to restore output.

3. Digital 3.25 V System Power Output

VDD3 is output. Feedback for the VDD3 is provided to the

switching controller (Pin (35) of IC501) so that PWM control

can be carried out.

4. Digital 1.7 V System Power Output

VDD1.8 is output. Feedback for the VDD1.8 is provided to the

switching controller (Pins (33) of IC501) so that PWM control

can be carried out.

5. Analog 3.45 V System Power Output

+3.45 V (A) is output. Feedback for the +3.45 V (A) is pro-

vided to the swiching controller (Pin (29) of IC501) so that

PWM control can be carried out.

6. Analog System Power Output

+12 V (A) and -6.5 V (A) are output. Feedback for the +12 V

(A) is provided to the swiching controller (Pin (31) of IC501)

so that PWM control can be carried out.

7. LCD System Power Output

LCD 12 V is output. Feedback for the LCD 12 V is provided to

the swiching controller (Pin (18) of IC501) so that PWM con-

trol can be carried out.

8. LCD Backlight System Power Output

Constant current is output to LED backlight. Feedback for the

voltage of R5045 is provided to the power controller (Pin (16)

of IC501) so that PWM control can be carried out.

– 6 –

1-4. ST1 STROBE CIRCUIT DESCRIPTION

1. Charging Circuit

When UNREG power is supplied to the charge circuit and the

CHG signal from microprocessor becomes High (3.3 V), the

charging circuit starts operating and the main electorolytic

capacitor is charged with high-voltage direct current.

However, when the CHG signal is Low (0 V), the charging

circuit does not operate.

1-1. Charging switch

The CHG signal becomes High, Q5407 becomes ON and the

charging circuit starts operating.

1-2. Power supply filter

C5401 constitutes the power supply filter. They smooth out

ripples in the current which accompany the switching of the

oscillation transformer.

1-3. Oscillation circuit

This circuit generates an AC voltage (pulse) in order to in-

crease the UNREG power supply voltage when drops in cur-

rent occur. This circuit generates a drive pulse with a frequency

of approximately 50-100 kHz. Because self-excited light omis-

sion is used, the oscillation frequency changes according to

the drive conditions.

1-4. Oscillation transformer

The low-voltage alternating current which is generated by the

oscillation control circuit is converted to a high-voltage alter-

nating current by the oscillation transformer.

1-5. Rectifier circuit

The high-voltage alternating current which is generated at

the secondary side of T5401 is rectified to produce a high-

voltage direct current and is accumulated at electrolytic ca-

pacitor C5412 on the main circuit board.

1-6. Voltage monitoring circuit

This circuit is used to maintain the voltage accumulated at

C5412 at a constance level.

After the charging voltage is divided and converted to a lower

voltage by R5417 and R5419, it is output as the monitoring

voltage VMONIT. When this VMONIT voltage reaches a speci-

fied level, the CHG signal is switched to Low and charging is

interrupted.

2. Light Emission Circuit

When FLCLT signals are input from the ASIC expansion port,

the stroboscope emits light.

2-1. Emission control circuit

When the FLCLT signal is input to Hi at the emission control

circuit, Q5409 switches on and preparation is made to the

light emitting. Moreover, when a FLCLT signal becomes Lo,

the stroboscope stops emitting light.

2-2. Trigger circuit

The Q5409 is turned ON by the FLCLT signal and light emis-

sion preparation is preformed. Simultaneously, high voltage

pulses of several kV are emitted from the trigger coil and ap-

plied to the light emitter.

2-3. Light emitting element

When the high-voltage pulse form the trigger circuit is ap-

plied to the light emitting part, currnet flows to the light emit-

ting element and light is emitted.

Beware of electric shocks.

– 7 –

1-5. SYA CIRCUIT DESCRIPTION

1. Configuration and Functions

For the overall configuration of the SYA block diagram, refer to the block diagram. The SYA block centers around a 8-bit micropro-

cessor (IC301), and controls camera system condition (mode).

The 8-bit microprocessor handles the following functions.

1. Operation key input, 2. Clock control and backup, 3. Power ON/OFF, 4. Storobe charge control

See next page

Signal

41~44

SCK

CARD

BACKUP_CTL

DC_IN

NOT USED

AV JACK

NOT USED

VDD2

VF. LED (R)

SELF LED

CLKSEL0

LCD ON 2

BL ON

PA ON2

MAIN RESET

VF. LED (G)

P ON

PA O N

ASIC TEST

NOT USED

ENA/DATA1

AVREF ON

NOT USED

SCAN IN2

SCAN IN1

SCAN IN0

VSS3

VDD3

RDSEL

CLK (SFW)

DATA0 (SFW)

NOT USED

SCAN OUT3~0

COMREQ_BOOT

I/O

Outline

Serial clock output

Memory card detection

Backup battery charge control (L= charge)

DC JACK detection

AV JACK detection

VDD

VF. LED (Red) (L= lighting)

Self-timer LED (L= lighting)

ARM system clock ON/OFF

D/D converter (LCD system) ON/OFF signal 2

LCD backlight ON/OFF signal

D/D converter (analog system) ON/OFF signal 2

System reset (MRST)

VF. LED (green) (L= lighting)

D/D converter (digital system) ON/OFF signal

ASIC control signal (ZTEST)

Select terminal for flash rewrite

AD VREF ON/OFF signal

Keymatrix input

GND

VDD

Select terminal for on chip debugger

Flash rewrite (combined with ROM debugger)

Keymatrix output

Command request input (combined with BOOT output)

D/D converter (analog system) ON/OFF signal

VSS2

GND

21 LCD ON

D/D converter (LCD system) ON/OFF signal

22 USB CONNECT

USB power detection terminal (L= detection)

23 PLLEN

PLL oscillation ON/OFF

25 CHG ON

Strobo charging control

– 8 –

2. Setting of external port and communication

The SYA block carries out overall control of camera operation by detecting the input from the keyboard and the condition of the

camera circuits. The 8-bit microprocessor reads the signals from each sensor element as input data and outputs this data to the

camera circuits (ASIC) or to the LCD display device as operation mode setting data. Fig. 5-1 shows the internal communication

between the 8-bit microprocessor and ASIC.

Table 5-1. 8-bit Microprocessor Port Specification

CHG VOL

Main capacitor charging voltage detection

Serial communication requirement signal

SREQ

Clock oscillation terminal for clock (32.768 kHz)

BATTERY I

Battery voltage detection

XCOUT

VDD1

VDD

BAT OFF

Battery OFF detection signal input

XIN I

Main clock oscillation terminal (4 MHz)

XOUT

Main clock oscillation terminal (4 MHz)

46~48

NOT USED

SCAN IN4

Key matrix input

SCAN IN3

Key matrix input

RESET

Microprocessor reset input

56 VSS1 -

GND

Fig. 5-1 Internal Bus Communication System

XCIN

Clock oscillation terminal for clock (32.768 kHz)

TEMP

Temperature detection

Serial data output

Serial data input

8-bit

Microprocessor

ASIC

SREQ

SDO

SDI

SCK

RESET

PLL EN

CLKSEL0

ZTEST

3. Key Operation

For details of the key operation, refer to the instruction manual.

Table 5-2. Key Operation

123

SCAN

OUT

SCAN

DOWN

TELE

RIGHT

REC

PW_TEST UP

WIDE

LEFT

TEST

ASS

LCD_ON/OFF

1st 2nd PLAY

MOVIE

PW_ON

– 9 –

ASIC,

memory

CCD

8bit

CPU

LCD

MONITOR

Power supply voltage

Power OFF

Playback mode

Shooting mode (OVF)

Shooting

USB connection

1.70 V, 3.25 V

12.0 V, -6.0 V

3.45 V

3.2 V

12 V

OFF

OFF 32KHz OFF

OFF

4MHz

OFF

4MHz

OFF

4MHz

OFF

4MHz

OFF

4MHz

OFF

Table 5-3. Power supply control

Shooting mode (LCD)

4. Power Supply Control

The 8-bit microprocessor controls the power supply for the overall system.

The following is a description of how the power supply is turned on and off. When the battery is attached, IC500 is operating and

creating 4.7 V, a regulated 3.2 V voltage is normally input to the 8-bit microprocessor (IC301) by IC302, clock counting and key

scanning is carried out even when the power switch is turned off, so that the camera can start up again.

When the power switch is off, the 8-bit microprocessor halts 4 MHz of the main clock, and operates 32.768 kHz of subclock.

When the battery is removed, the 8-bit microprocessor power switches the battery for memory backup by IC302, and operates at

low consumption. At this condition, the 8-bit microprocessor halts the main clock, and operates clock counting by sub clock.

Also, the battery for backup is charged 10 hours from it to be attached.

When the power switch is on, the 8-bit microprocessor starts processing. The 8-bit microprocessor first sets both the PON signal

at pin (19) and the PAON signal at pin (20) to High, and then turn on the power circuit. After PON signal is to High, sets external

port of ASIC after approximately 150 ms. According to setting of this external port, carry out setting of the operating frequency

and oscillation control in the ASIC. Also, it starts communication with ASIC, and confirms the system is operative.

When the through image is operating, set the PAON signal to High and then turn on the CCD. When the through image is playing,

set the PAON signal to Low and then turn off the CCD. When LCD panel turns on, set LCD ON signal at pin (21) and LCD ON2

signal at pin (14) to High, and then turn on the power. Set BL ON signal at pin (15) to High, and turn on the backlight power.

When the power switch is off, the lens will be stowed, and PON, PAON, LCDON and BL ON signals to Low and the power supply

to the whole system is halted. The 8-bit microprocessor halts oscillation of the main clock, and set operation mode of clock

oscillation.

– 10 –

2. DISASSEMBLY

2-1. REMOVAL OF CABI BACK AND CABI FRONT

NOTE: Discharge a strobe capacitor

with the discharge jig (VJ8-0188) for

electric shock prevention.

1. Two screws 1.4 x 2

2. Two screws 1.4 x 2

3. Five screws 1.4 x 3.5

4. Cover card

5. Cabi back

6. Cabi front

7. FPC

8. Holder cover card

9. Spring cover card

– 11 –

2-2. REMOVAL OF LCD

1. Screw 1.4 x 3.5

2. FPC

3. FPC

4. Spacer lens FPC

5. LCD

6. Holder monitor

– 12 –

2-3. REMOVAL OF CP1 BOARD AND PW2 BOARD

1. Connector

2. Spacer CP1

3. Screw 1.4 x 3.5

4. Holder button zoom

5. FPC

6. Two connectors

7. Connector

8. Microphone

9. Remove the solder.

10. CP1 board

11. Screw 1.4 x 3.5

12. Screw 1.4 x 3.5

13. PW2 board

14. Shaft cover battery

15. Cover battery

16. Spring cover battery

17. Holder battery

18. Speaker, 8

– 13 –

2-4. REMOVAL OF LENS ASSEMBLY, ST1 BOARD AND BOARD LOCATION

1. Three screws 1.4 x 3.5

2. Lens assembly

3. Spacer CCD

4. Three screws 1.4 x 4

5. CA1 board

6. Screw 1.4 x 3.5

7. Two screws 1.4 x 3.5

8. Guide shutter

9. Screw 1.4 x 3.5

10. Cabinet inner

11. Spacer ST1

12. Screw 1.4 x 3.5

13. Cover triger

14. Remove the solder.

15. ST1 board

CA1 board

PW2 board

CP1 board

ST1 board

– 14 –

3. ELECTRICAL ADJUSTMENT

3-1. Table for Servicing Tools

Note: J-1 Pattern box (color viewer) is 100 - 110 VAC only.

3-2. Equipment

1. Oscilloscope

2. Digital voltmeter

3. AC adaptor

4. PC (IBM R -compatible PC, Pentium processor, Window

98 or Me or 2000 or XP)

3-3. Adjustment Items and Order

1. IC501 Oscillation Frequency Adjustment

2. Lens Data Adjustment

3. Lens Adjustment

4. AWB Adjustment

5. CCD White Point Defect Detect Adjustment

6. CCD Black Point And White Point Defect Detect Adjust-

ment In Lighted

Note: If the lens, CCD and board in item 2-6, it is necessary

to adjust again. Item 2-6 adjustments should be carried

out in sequence.

3-4. Setup

1. System requirements

Windows 98 or Me or 2000 or XP

IBM R -compatible PC with pentium processor

CD-ROM drive

3.5-inch high-density diskette drive

USB port

40 MB RAM

Hard disk drive with at least 15 MB available

VGA or SVGA monitor with at least 256-color display

2. Installing calibration software

1. Insert the calibration software installation diskette into your

diskette drive.

2. Open the explorer.

3. Copy the DscCalDI_141 folder on the floppy disk in the FD

drive to a folder on the hard disk.

3. Installing USB driver

Install the USB driver with camera or connection kit for PC.

4. Pattern box (color viewer)

Turn on the switch and wait for 30 minutes for aging to take

place before using Color Pure. It is used after adjusting the

chroma meter (VJ8-0192) adjust color temperature to 3100 ±

20 K and luminosity to 900 ± 20 cd/m

. Be careful of handling

the lump and its circumference are high temperature during

use and after power off for a while.

5. Computer screen during adjustment

Ref. No.

Name

Part code

J-1

J-2

J-3

VJ8-0190

VJ8-0244

Pattern box (color viewer)

Siemens star chart

Calibration software

J-4

Number

1Chroma meter

VJ8-0192

Spare lump

VJ8-0191

J-5

J-1 J-2

J-3

J-4

J-5

Discharge jig

VJ8-0188

J-6

Firmware

Data

AWB

Focus

UV Matrix

R Bright

RGB Offset

Tint

B Bright

Gain

Phase

LCD

Calibration

Upload

Initialize

LCD Type

H AFC Test

VCOMDC

VCOMPP

Cal Data

Cal Mode

EVF

USB storage

Get

Set

VID

Set

PID

Set

Serial

Set

Rev.

Set

Setting

Language

Video Mode

VCO

Factory Code

Backrush pulse :

Set

Get

Hall Cal.

– 15 –

3-5. Connecting the camera to the computer

1. Turn on the camera.

2. Line up the arrow on the cable connector with the notch on the camera's USB port. Insert the connector.

3. Locate a USB port on your computer.

4. Choose the SETUP, and choose the Transfer mode.

5. Choose the Data storage, and press the SET button.

AC adaptor

To USB port

USB cable

– 16 –

3-6. Adjust Specifications

[CP1 board (Side B)]

Note:

1. Frequency adjustment can be carried out in through image

mode.

1. IC501 Oscillation Frequency Adjustment

Adjustment method:

1. Adjust with VR501 to 510.6 ± 1 kHz.

2. Lens Data Adjustment

Preparation:

POWER switch: ON

Adjustment method:

1. Double-click on the DscCalDi.exe.

2. Select “Lens Data” in the LCD “Test”.

3. Type in the value given on the bar code that is attached to

the back of the lens into the blank space next to “PI switch”

in the Lens data dialog box.

The first digit of the bar code value is a “0” or a “1”.

4. Type in the value given on the bar code that is attached to

the surface of the lens into the blank space next to “Delta

SB” in the Lens data dialog box.

However, for lenses that have a blank line instead of a bar

code, type in “202020”.

The first digit of the bar code value is a “2” or a “3”.

5. Click “Set” at the right side of Lens data Dialog box.

3. Lens Adjustment

Preparation:

POWER switch: ON

Adjustment condition:

More than A3 size siemens star chart

Fluorescent light illumination with no flicker

Illumination above the subject should be 400 lux ± 10 %.

Adjustment method:

1. Set the siemens star chart 150 cm ± 3 cm so that it be-

comes center of the screen.

2. Double-click on the DscCalDi.exe.

3. Click the Focus, and click the Yes.

4. Lens adjustment value will appear on the screen.

(When adjustment is failed, “NG: X” will display.)

5. Click the OK.

Measuring Point

ADJ. Location

Measuring Equipment

ADJ. Value

CL511

Frequency counter

VR501

510.6 ± 1 kHz

CL511

VR501

Camera

Approx.

150 cm 3 cm

Siemens

star chart

DscCalDi x

Focus Result

NG:

– 17 –

4. AWB Adjustment

Preparation:

POWER switch: ON

Adjusting method:

1. When setting the camera in place, set it to an angle so that

nothing appears in any part of the color viewer except the

white section. (Do not enter any light.)

2. Double-click on the DscCalDi.exe.

3. Click the AWB, and click the Yes.

4. AWB adjustment value will appear on the screen.

5. Click the OK.

Adjustment value determination is effectuated using the "AGC",

“CHECK" and "IRIS" values.

If AGC=a1, a2, a3, a4, a5 and CHECK=wc0, wc1, wc2, the

adjustment values fulfill the conditions below, they are deter-

mined as within specifications.

Adjustment value determination

a1<1023, a2<1023, a3<1023, a4<1023, a5<1023

wc0=128 ± 2, wc1=128 ± 2, wc2=130 ± 40

IRIS<30

Adjustment values other than the above are irrelevant.

Camera

Pattern box

(color viewer)

5. CCD White Point Defect Detect Adjustment

Preparation:

POWER switch: ON

Adjustment method:

1. Double-click on the DscCalDi.exe.

2. Select “CCD Defect” on the LCD “Test”, and click the “Ye s ”.

3. After the adjustment is completed, OK will display.

4. Click the OK.

6. CCD Black Point And White Point Defect Detect

Adjustment In Lighted

Preparation:

POWER switch: ON

Setting of pattern box:

Color temperature: 3100 ± 20 (K)

Luminance: 900 ± 20 (cd/m

)

Adjusting method:

1. Set the camera 0 cm from the pattern box. (Do not enter

any light.)

2. Double-click on the DscCalDi.exe.

3. Select “CCD Black” on the LCD “Test”, and click the “Ye s ”.

4. After the adjustment is completed, the number of defect

will appear.

Dsc Calibration

AWB Result:

AGC=176,345,513,682,852

3F_AGC=1,2

WB=278,512,648

CHECK=127,128,142

MS=2200,3579

IRIS=16

Copy

Camera

Pattern box

(color viewer)

– 18 –

3-7. Factory Code Setting

1. Check the "Factory Code" display within the Setting group.

2. For NTSC general area

If "FC_SANYO_U" does not appear, click on the " " mark

located on the right of the "Factory Code" display BOX and

select "FC_SANYO_U".

3. For Europe and PAL general area

If "FC_SANYO_EX" does not appear, click on the " " mark

located on the right of the "Factory Code" display BOX and

select "FC_SANYO_EX".

3-8. Language Setting

1. Click on the " " mark located on the right of the

"Language" display BOX.

2. Select language. (Default is English.)

3. End "DscCal" and remove the camera before turning the

camera power OFF.

Firmware

Data

AWB

Focus

UV Matrix

R Bright

RGB Offset

Tint

B Bright

Gain

Phase

LCD

Calibration

Upload

Initialize

LCD Type

H AFC Test

VCOMDC

VCOMPP

Cal Data

Cal Mode

EVF

USB storage

Get

Set

VID

Set

PID

Set

Serial

Set

Rev.

Set

Setting

Language

Video Mode

VCO

Factory Code

Backrush pulse :

Set

Get

Hall Cal.

3-9. Firmware uploading procedure

1. Uploading the firmware should be carried out if the version

number (COMPL PWB XX-X) on the replacement circuit

board is lower than the version of the distributed firmware.

For XX-X, enter the name of the circuit board containing the

firmware.

2. The firmware is distributed by e-mail in self-extracting archive

format. Change the extension of the distributed file to .EXE

and save it in your proferred folder.

3. When you double-click the saved file, the firmware (binary

file) will be saved in the same folder.

4. The firmware must not be distributed without permission.

1. Overwriting firmware from the SD card

Preparation:

SD card: SD card with firmware rewritten into the root direc-

tory

Data: S71ANxxx.BIN (xxx: version)

Overwriting method:

1. Insert the above SD card.

2. Press and hold the PLAY button.

3. Press the MENU button.

4. Choose SETUP, and press the center button.

5. Choose the Format.

6. Press the left key for 2 seconds. FIRMWARE UPDATE will

display.

7. Choose YES.

8. Press the center button. Update is starting.

Note:

Do not turn off the camera’s power or remove the SD card

while the firmware is being updated.

The power will turn on automatically after the update is com-

plete.

2. Overwriting firmware from USB

Overwriting method:

1. Connect the camera to the computer with USB cable, and

turn on the camera.

2. Check that the camera is fully connected to the computer.

3. Double-click on the DscCalDi.exe.

4. Click the Firmware.

5. Choose the fimware file to use for overwriting.

6. Click the Yes. Update is starting.

Note:

Do not turn off the camera’s power or remove the SD card or

end the calibration software while the firmware is being up-

dated.

After the update is complete, disconnect the USB cable and

turn the camera’s power off and back on again.

– 19 –

4. USB STORAGE INFORMATION

REGISTRATION

USB storage data is important for when the camera is con-

nected to a computer via a USB connection.

If there are any errors in the USB storage data, or if it has not

been saved, the USB specification conditions will not be sat-

isfied, so always check and save the USB storage data.

Preparation:

POWER switch: ON

Adjustment method:

1. Connect the camera to a computer. (Refer to 3-5. Con-

necting the camera to the computer on the page 15.)

2. Double-click on the DscCalDi.exe.

3. Click on the Get button in the USB storage window and

check the USB storage data.

VID: SANYO

PID: A5

Serial:

Rev. : 1.00

4. Check the “Serial” in the above USB storage data. If the

displayed value is different from the serial number printed

on the base of the camera, enter the number on the base

of the camera. Then click the Set button.

5. Next, check VID, PID and Rev. entries in the USB storage

data. If any of them are different from the values in 3. above,

make the changes and then click the corresponding Set

button.

Firmware

Image

AWB

Focus

UV Matrix

R Bright

RGB Offset

Tint

B Bright

Gain

Phase

LCD

Calibration

Upload

Initialize

LCD Type

H AFC Test

VCOMDC

VCOMPP

Cal Data

Cal Mode

EVF

USB storage

Get

Set

VID

Set

PID

Set

Serial

Set

Rev.

Set

Setting

Language

Video Mode

VCO

Factory Code

Hall Cal.

– 20 –

5. TROUBLESHOOTING GUIDE

POWER LOSS INOPERTIVE

IC302-7

(UNREG)

CHECK PWA

IC301-9, 36, 59

(VDD)

CHECK IC302-6

IC301-53

(RESET)

IC301-49

(BAT OFF)

CHECK IC302-5,

RB305

CHECK IC302-4,

RB305

IC301

4 MHz OSCILLATION

CHECK X3001

IC301

32 kHz OSCILLATION

CHECK X3002,

R3008, C3008, C3012

CHECK IC301

PUSH SHUTTER

BUTTON

IC301

(SCAN IN)

PULSE INPUT

CHECK

SHUTTER SW S5452,

R3004

IC301-19, 20

(P ON, P(A) ON)

CHECK IC301,

PWA BLOCK

IC301-17, 24

CHECK IC301,

DMA BLOCK

CHECK DMA BLOCK

TAKING INOPERATIVE

LOW

HIGH

YES

HIGH

LOW

IC301 (SCAN IN)

PULSE INPUT

CHECK

POWER SW S3510

YES

SERIAL

COMMUNICATION

CHECK IC301

YES

Page is loading ...

Sanyo Xacti VPC-A5 User manual

Brand: Sanyo

Model: Xacti VPC-A5

Type: User manual

This manual is also suitable for

Xacti VPC-A5EX

Download PDF

report

Sanyo Xacti VPC-A5 User manual

This manual is also suitable for

Sanyo Xacti VPC-A5 User manual

Related papers

Other documents