American Megatrends K1 User manual

Category
Software
Type
User manual

This manual is also suitable for

MegaRAC™ K1
User’s Guide
MAN-933
03/31/05
MegaRAC K1 User’s Guide
ii
© Copyright 1985-2010 American Megatrends, Inc.
All rights reserved.
American Megatrends, Inc.
5555 Oakbrook Parkway, Building 200,
Norcross, GA 30093
This publication contains proprietary information which is protected by copyright. No
part of this publication can be reproduced, transcribed, stored in a retrieval system,
translated into any language or computer language, or transmitted in any form
whatsoever without the prior written consent of the publisher, American Megatrends, Inc.
American Megatrends, Inc. acknowledges the following trademarks:
Intel is a registered trademark of the Intel Corporation.
MS-DOS and Microsoft are registered trademarks of the Microsoft Corporation.
Microsoft Windows is a trademark of the Microsoft Corporation.
IBM, AT, VGA, PS/2, and OS/2 are registered trademarks and XT and CGA are
trademarks of the International Business Machines Corporation.
Other trademarks and trade names may be used in this document to refer to either the
entities claiming the marks and names or their products. American Megatrends, Inc.
disclaims any proprietary interest in trademarks and trade names other than its own.
Revision History
12/15/03 Initial release.
02/25/04 Updated MegaRAC K1 hardware images to reflect new chassis design.
03/03/04 Updated GUI images to reflect firmware version 1.0.12.
04/29/04 Updated GUI images to reflect firmware version 1.0.15.
12/17/04 Updated GUI images to reflect firmware version 2.0.
03/29/05 Updated GUI images to reflect firmware version 2.0.8.
Preface
iii
Table of Contents
Chapter 1 Introduction ................................................................................................................ 1
Key Features................................................................................................................................ 1
Key Benefits ................................................................................................................................. 1
Hardware Features ...................................................................................................................... 1
Remote Software ......................................................................................................................... 2
Upgrade Your Existing Analog KVM............................................................................................ 2
Chapter 2 Installing Your MegaRAC K1 .................................................................................... 3
MegaRAC K1 Installation and Setup ........................................................................................... 3
Step 1 Unpack the MegaRAC K1 ................................................................................................ 4
MegaRAC K1 Ports and Status LED........................................................................................ 4
MegaRAC K1 Cables and USB Port ........................................................................................ 5
Recovery Button....................................................................................................................... 6
Step 2 Connect Cables ................................................................................................................ 7
USB Cable................................................................................................................................ 7
Network Port............................................................................................................................. 7
AUX Port................................................................................................................................... 8
RS-232 Port.............................................................................................................................. 8
DC 6V Port ............................................................................................................................... 9
PS/2 and Video Cables ............................................................................................................ 9
Step 3 Confirm the Motherboard’s BIOS Settings ..................................................................... 10
Step 4 Install the K1 Virtual CD-ROM Drivers ........................................................................... 10
Step 5 Set up Your Client System’s Internet Browser ............................................................... 11
Step 6 Connect to the MegaRAC K1 from a Client System ...................................................... 15
On Screen Display (OSD) Utility ............................................................................................ 15
Connecting to the K1.............................................................................................................. 16
Chapter 3 Using Your MegaRAC K1 ........................................................................................ 17
K1 GUI Overview ....................................................................................................................... 17
Default Root User Name and Password.................................................................................... 18
K1 GUI Explained ...................................................................................................................... 19
Menu Bar ................................................................................................................................ 19
Quick Launch Icons................................................................................................................ 20
Manage Group ........................................................................................................................... 20
Remote Console ........................................................................................................................ 21
Redirection ................................................................................................................................. 22
Setting up Internet Explorer....................................................................................................22
Disabling Mouse Acceleration ................................................................................................ 26
Disabling Mouse Acceleration on Windows XP Operating Systems...................................... 26
Disabling Mouse Acceleration on Windows 2000 and ME Operating Systems..................... 26
Disabling Mouse Acceleration on Linux ................................................................................. 26
Disabling Mouse Acceleration on NetWare 6 servers running Java 1.4.1............................. 26
Disabling Mouse Acceleration on NetWare 6 servers running Java 1.3.1 CSP8/9 ............... 26
Starting Redirection................................................................................................................ 27
Authentication Dialog Box Options......................................................................................... 31
Remote Console Shortcut Key Combinations........................................................................ 32
Console Redirection Window ................................................................................................. 33
Console Redirection Toolbar.................................................................................................. 38
Console Redirection Toolbar Status ...................................................................................... 38
Console Redirection Toolbar Toggle Buttons ........................................................................ 39
MegaRAC K1 User’s Guide
iv
Table of Contents
Console Redirection Toolbar (Full Screen Mode).................................................................. 40
Console Redirection Toolbar (Full Screen Mode) Buttons..................................................... 41
Start CD-ROM Drive Redirection ........................................................................................... 43
Stop CD-ROM Drive Redirection ........................................................................................... 45
Stopping Console Redirection................................................................................................ 46
Video Parameters................................................................................................................... 47
Dual Mouse ............................................................................................................................ 48
Bandwidth Usage ................................................................................................................... 49
Disable Local Video................................................................................................................ 49
Upgrade Firmware ..................................................................................................................... 50
Updating Your MegaRAC K1’s Firmware............................................................................... 51
Power Control ............................................................................................................................ 57
Power Buddy Control .............................................................................................................57
Through IPMI.......................................................................................................................... 58
Using the Serial Port to Control the Power ............................................................................ 59
Toggle Port Usage ................................................................................................................. 59
Power Management via Serial Port........................................................................................ 60
Resetting the K1 ........................................................................................................................ 61
Configure Group ........................................................................................................................ 62
Users.......................................................................................................................................... 63
Adding Users .......................................................................................................................... 64
Removing Users..................................................................................................................... 65
Viewing and Editing Users ..................................................................................................... 66
Network ...................................................................................................................................... 67
Firewall....................................................................................................................................... 69
SSL Certificate ........................................................................................................................... 71
View Group ................................................................................................................................ 73
General Information ................................................................................................................... 73
General Information : Firmware.............................................................................................. 73
General Information : Features .............................................................................................. 74
General Information : Detailed Versions ................................................................................ 74
Health Information...................................................................................................................... 75
Language Option ....................................................................................................................... 75
Appendix A On Screen Display (OSD).................................................................................. 77
Overview .................................................................................................................................... 77
Entering OSD............................................................................................................................. 77
Navigation .................................................................................................................................. 78
Menu .......................................................................................................................................... 79
Login .......................................................................................................................................... 80
General ...................................................................................................................................... 80
Network ...................................................................................................................................... 81
User............................................................................................................................................ 83
Firewall....................................................................................................................................... 85
Firewall Allow Rules ............................................................................................................... 85
Firewall Block Rules ............................................................................................................... 86
Appendix B KSeek Utility....................................................................................................... 89
Overview .................................................................................................................................... 89
Locating Your MegaRAC K1...................................................................................................... 89
IP Address Range...................................................................................................................... 93
Usage......................................................................................................................................... 96
Preface
v
Table of Contents
Appendix C CURI Client......................................................................................................... 97
Overview .................................................................................................................................... 97
CURI (Common User Remote API Interface) ........................................................................ 97
CURI Client ................................................................................................................................ 97
Running the CURI Client from Microsoft Windows ................................................................ 97
For Network Connection......................................................................................................... 97
For Inband Connection...........................................................................................................98
Command Options .................................................................................................................98
Appendix D SConsole Utility ................................................................................................. 99
Overview .................................................................................................................................... 99
Prerequisites .......................................................................................................................... 99
Hardware Setup ......................................................................................................................... 99
Setting up Hyper Terminal ....................................................................................................... 101
Powering on the K1.................................................................................................................. 102
Logging In ................................................................................................................................ 103
Default Root User Name and Password .............................................................................. 103
Main Menu ............................................................................................................................... 104
General Information ................................................................................................................. 105
Network Information................................................................................................................. 105
User Information ...................................................................................................................... 106
Appendix E MegaRAC Port Table ....................................................................................... 107
MegaRAC Port Table............................................................................................................... 107
Appendix F MAC Address Map........................................................................................... 109
Notes........................................................................................................................................ 110
Appendix G Troubleshooting .............................................................................................. 111
Blinking Red LED..................................................................................................................... 111
Problem ................................................................................................................................ 111
Symptom .............................................................................................................................. 111
Solution................................................................................................................................. 111
Complete Flash........................................................................................................................ 112
Problem ................................................................................................................................ 112
Symptom .............................................................................................................................. 112
Solution................................................................................................................................. 112
Index ........................................................................................................................................... 113
MegaRAC K1 User’s Guide
vi
Limited Warranty
The buyer agrees that if this product proves to be defective, American Megatrends is only
obligated to repair or replace this product at American Megatrends’ discretion according
to the terms and conditions of the warranty registration card that accompanies this
product. American Megatrends shall not be liable in tort or contract for any loss or
damage, direct, incidental or consequential resulting from the use of this product. Please
see the Warranty Registration Card shipped with this product for full warranty details.
Technical Support
AMI provides technical support for AMI products purchased directly from AMI or from
an AMI-authorized reseller only.
If… Then…
You purchased this product from AMI or from a certified
AMI reseller,
Call AMI technical support at 770-246-8645. Please be
prepared to specify the serial number of the product.
This AMI product was installed as part of a system
manufactured by a company other than AMI or you
purchased an AMI product from an unauthorized reseller,
Call the technical support department of the computer
manufacturer or the unauthorized reseller. AMI does not
provide direct technical support in this case.
If an American Megatrends MegaRAC™ K1 fails to operate as described or you are in
doubt about a configuration option, please call technical support at 770-246-8645.
Web Site
We invite you to access the American Megatrends World Wide Web site at:
http://www.ami.com/
Preface
vii
Disclaimer
This manual describes the operation of the American Megatrends MegaRAC™ K1.
Although efforts have been made to assure the accuracy of the information contained
here, American Megatrends expressly disclaims liability for any error in this information,
and for damages, whether direct, indirect, special, exemplary, consequential or otherwise,
that may result from such error, including but not limited to the loss of profits resulting
from the use or misuse of the manual or information contained therein (even if American
Megatrends has been advised of the possibility of such damages). Any questions or
comments regarding this document or its contents should be addressed to American
Megatrends at the address shown on the inside of the front cover.
American Megatrends provides this publication “as is” without warranty of any kind,
either expressed or implied, including, but not limited to, the implied warranties of
merchantability or fitness for a specific purpose.
Some states do not allow disclaimer of express or implied warranties or the limitation or
exclusion of liability for indirect, special, exemplary, incidental or consequential
damages in certain transactions; therefore, this statement may not apply to you. Also, you
may have other rights which vary from jurisdiction to jurisdiction.
This publication could include technical inaccuracies or typographical errors. Changes
are periodically made to the information herein; these changes will be incorporated in
new editions of the publication. American Megatrends may make improvements and/or
revisions in the product(s) and/or the program(s) described in this publication at any time.
Requests for technical information about American Megatrends products should be made
to your American Megatrends authorized reseller or marketing representative.
Retail Packing List
You should have received the following:
a MegaRAC™ K1
one USB cable
RS-232 serial port service cable
an AC Adapter
this MegaRAC™ K1 User's Guide (located on the MegaRAC™ K1 CD)
a MegaRAC™ K1 Quick Installation Guide
a MegaRAC™ K1 CD
a warranty card
Note: Your MegaRAC K1 (series 933) may or may not ship with everything listed in the Retail
Packing List. Contact your AMI authorized reseller to find out what is shipped with your
MegaRAC K1.
Note: The RS-232 serial port is not designed for use with an external serial modem.
MegaRAC K1 User’s Guide
viii
FCC Class B Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Warning
Changes or modifications to this device not expressly approved by American
Megatrends could void the user’s authority to operate the equipment.
Chapter One : Introduction
1
Chapter 1 Introduction
Key Features
Feature Description
Zero-U Form Factor
No Rack or Desktop Space Required
Dimensions: 83 mm x 80 mm x 26 mm
Video
Provides Remote Video Display, Fast Redirection and Animation
Resolution up to 1280 x 1024
Keyboard Mouse
Allows Remote Keyboard and Mouse Control
Setup
Non-intrusive Installation
Sits Outside the KVM, Server or PC
Does Not Affect Local Operations
Easy to Add into Existing
Installations
Attaches to Standard KVM or Computer Ports
Remote Boot
USB 2.0 Mass Storage Emulation Allows the Host System to Boot from a
Remote Drive Over the Network
Web-Based Management
Allows for Fast Browser Response for Redirection and Configuration Screens
KSeek
Discovers the Deployed MegaRAC K1s in the Network
Key Benefits
Benefit Description
Internet Monitoring and
Control of Any Server/PC
Attaches to an Analog KVM, Server or PC
Provides for Remote Monitoring or Video
Allows Remote Control of Keyboard and Mouse
Controls any Server or PC Anywhere from Anyplace
Non-Intrusive
Easy to Set up
Retrofit
Performance
AMI’s Proprietary Technology Provides Incredible Video Performance, Seen
Only in Far More Complex and Expensive Products
Hardware Features
Feature Description
Embedded Boards
Series 933 (Baseboard)
Series 934 (DVI Video Board)
or
Series 933 (Baseboard)
Series 935 (VGA Video Board)
Processor
200 MHz
300 MIPS
Memory
32 MB
Flash
8 MB
Video Interface
Dual Mode LCD Monitor Controller
Ports
USB 2.0
Network
10/100 Mbps
Cont’d
MegaRAC K1 User’s Guide
2
Remote Software
Application Description
KSeek
Discovers MegaRAC K1s Deployed in a Network
Uses AMI Proprietary CURI Protocol for Discovery
Upgrade Your Existing Analog KVM
You can… Benefit
Upgrade your existing analog KVM switch installations,
easily and conveniently, to KVM over IP
Receive significant cost savings, allowing you to
continue to deploy your existing analog KVM switches
Attach to a multi-port analog KVM switch Control multiple servers using just one MegaRAC K1
Display multiple views Multiple remote sites can simultaneously monitor the
MegaRAC K1
KVM
16
LAN
Remote
Console
Remote
Console
Local
Console
Servers Being
Controlled By
the Analog KVM
Analog or
Digital KVM
TCP/IP
Chapter Two : Installing Your MegaRAC K1
3
Chapter 2 Installing Your MegaRAC K1
MegaRAC K1 Installation and Setup
www.ami.com
MegaRAC K1
TM
Use the following steps to attach the MegaRAC K1 to your host system.
Step Action
1 Unpack the MegaRAC K1
2 Connect Cables
3 Confirm the Motherboard’s BIOS Settings
4 Install the K1 Virtual CD-ROM Drivers
5 Set up Your Client System’s Internet Browser
6 Connect to the MegaRAC K1 from a Client System
Note: Inspect the cardboard carton for obvious damage.
MegaRAC K1 User’s Guide
4
Step 1 Unpack the MegaRAC K1
MegaRAC K1 Ports and Status LED
The following illustration shows the ports located on the leading edge of the K1.
Familiarize yourself with the location of all the ports before attempting to install the K1
onto your host system.
Recovery
Button
www.ami.com
MegaRAC K1
TM
Item Icon Description
Network Connect your network cable to this port.
Recovery
Button
none This button allows you to set the MegaRAC K1 into recovery mode so that it can be
located with the RacMfgDiag application.
Note: The Recovery button and the RacMfgDiag application are not described
in this manual. They are primarily used as a means to service the
MegaRAC K1.
WARNING!
Damage to the K1 Recovery Button can occur if you press too hard
RS-232 This port is the MegaRAC K1 serial port and is used to configure the MegaRAC K1
in conjunction with the KSeek Utility.
AUX This port is used to attach to an auxiliary optional device. This auxiliary port is
originally designed to allow connection to a device that can control the power on
the host system. It is also designed to supply power to the K1. This would eliminate
the need for the AC Adapter cable.
Note: As of the release of this document, no AUX devices have been designed.
The AUX Port is for future expandability and is an example of AMI’s
forward thinking.
DC 6V This port is used to supply the MegaRAC K1 with power.
Note: You must connect AC power before attaching the PS/2 mouse.
Status LED none
This LED is used to display the status of the MegaRAC K1. See the
illustration below.
Color
Red
Amber
Green
Description
Failed
Booting
On and Ready
www.ami.com
MegaRAC K1
TM
Cont’d
Chapter Two : Installing Your MegaRAC K1
5
Step 1 Unpack the MegaRAC K1, Continued
MegaRAC K1 Cables and USB Port
The following illustration shows the cables and USB port located on the upper edge of
the K1. Familiarize yourself with the location of all the cables and the USB port before
attempting to install the K1 onto your host system.
www.ami.com
MegaRAC K1
TM
Item Icon Description
Out This cable is used to connect to the local VGA/DVI display device, such as an LCD
Panel or Monitor.
In This cable is used to connect to the VGA/DVI graphics adapter on your host
system.
USB Attach the MegaRAC USB cable to this port. Attach the other end of the USB cable
to the USB port on your host system.
Mouse
Keyboard
These two cables are used to connect from the PS/2 Keyboard and Mouse port on
your host system to the PS/2 Keyboard and Mouse.
Note: You must connect AC power before attaching the PS/2 mouse.
Cont’d
MegaRAC K1 User’s Guide
6
Step 1 Unpack the MegaRAC K1, Continued
Recovery Button
Push in carefully and
hold in while applying
Power
www.ami.com
MegaRAC K1
TM
You can put the MegaRAC K1 into recovery mode by using a straightened paper clip.
Push in the tiny recovery switch while inserting power.
Note: The Recovery button and the RacMfgDiag application are not described in this manual.
They are primarily used as a means to service the MegaRAC K1.
Warning
Damage to the K1 Recovery Button can occur if you press too hard
Chapter Two : Installing Your MegaRAC K1
7
Step 2 Connect Cables
USB Cable
Connect the USB cable to the K1 as illustrated below:
www.ami.com
MegaRAC K1
TM
Network Port
Physically attach your K1 to your network by plugging an Ethernet Cable into the K1
Network Port.
Plug your Ethernet Cable
into the Network Port
www.ami.com
MegaRAC K1
TM
Cont’d
MegaRAC K1 User’s Guide
8
Step 2 Connect Cables, Continued
AUX Port
This port is used to attach to an auxiliary optional device. This auxiliary port is originally
designed to allow connection to a device that can control the power on the host system. It
is also designed to supply power to the K1. This would eliminate the need for the AC
Adapter cable.
Note: As of the release of this document, no AUX devices have been designed. The AUX Port
is for future expandability and is an example of AMI’s forward thinking.
Plug your Auxiliary Cable
into the port marked AUX
www.ami.com
MegaRAC K1
TM
RS-232 Port
This port is the MegaRAC K1 serial port and is used to configure the MegaRAC K1.
Attach the supplied K1 serial cable to the RS-232 port. Connect the DB 9-pin female
connector of the serial cable to a system that has a Telnet Client such as HyperTerminal.
You can obtain the IP address using this method.
Plug your Serial Cable
into the port marked RS232
www.ami.com
MegaRAC K1
TM
Note: To get the IP address on your MegaRAC K1 locally, you can use the RS-232 port in
conjunction with the KSeek Utility or use the On Screen Display (OSD) feature.
Cont’d
Chapter Two : Installing Your MegaRAC K1
9
Step 2 Connect Cables, Continued
DC 6V Port
You can attach the cables in any order except for the AC Adapter cable. The AC Adapter
cable must be attached to the K1 before attaching the PS/2 mouse.
Plug your AC Adapter
into the Power Port
www.ami.com
MegaRAC K1
TM
PS/2 and Video Cables
Your K1 will boot up and become active. The Status LED will be amber. Connect the
PS/2 Keyboard cable, PS/2 Mouse cable, Video In cable, and opposite side of the USB
cable to your host system. Connect your PS/2 Keyboard and PS/2 Mouse to the K1 PS/2
Keyboard and PS/2 Mouse connector. Plug the Video Out cable to your Display Device.
www.ami.com
MegaRAC K1
TM
Note: You must connect AC power before attaching the PS/2 mouse.
MegaRAC K1 User’s Guide
10
Step 3 Confirm the Motherboard’s BIOS Settings
Power on the motherboard and enter the BIOS. Using the following table, confirm that
your motherboard’s BIOS settings are correct.
BIOS Section Setting
Boot Options> ATAPI CDROM AMI Virtual CDROM
Advanced> PCIPnP> Configuration> Legacy USB Support Enable
Save the BIOS settings and restart the computer.
Note: Make sure that your motherboard BIOS supports Legacy USB devices, USB Boot or Boot
to USB.
Note: On some serverboards, depress the <CTRL>, <ALT>, and <ESC> keys simultaneously to
enter the BIOS. On others use the <F2> keys. On most serverboards that use the
AMIBIOS, you can invoke the BIOS setup by depressing the <DEL> key during POST.
Step 4 Install the K1 Virtual CD-ROM Drivers
Install the operating system (if applicable) on the host system.
(Windows 2000/XP only) When prompted for the virtual CD-ROM drivers, select the
default option Microsoft Windows provides. The Virtual CD-ROM device does not
require any special drivers.
Chapter Two : Installing Your MegaRAC K1
11
Step 5 Set up Your Client System’s Internet Browser
You must first set up your Internet browser on the client system before you can redirect
the host system’s console.
Note: At a minimum you must have Internet Explorer 6.0 (and above) or Mozilla 1.6 (and
above) installed on your client system.
Follow the instructions in the table below:
Step Description
1 Open Internet Options. To get there, open your Internet Explorer browser, left click Tools and then
Internet Options.
2 The Internet Options window opens. Left click the Settings button.
Cont’d
MegaRAC K1 User’s Guide
12
Step 5 Set up Your Client System’s Internet Browser, Continued
Step Description
3 The Settings window opens. Left click the Every visit to the page button or Automatically button. Left
click the OK button to apply the change and to go back to the Internet Options window.
Note: Other settings can cause old data to be displayed when performing operations on the MegaRAC
K1.
4 Next, you must set up Internet Explorer to allow the downloading of Signed ActiveX controls and also
allow it to run Signed ActiveX controls. To do this, left click the Security tab and then the Custom Level
button.
Cont’d
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122

American Megatrends K1 User manual

Category
Software
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI