Garmin GC™ 200 Marine IP Camera Owner's manual

GC™ 200 Marine IP Camera
Garmin
Brand
Garmin
Model
GC™ 200 Marine IP Camera
Type
Owner's manual
GC
™
200 IP MARINE CAMERA
Installation Instructions 2
Instructions d'installation 4
Istruzioni di installazione 6
Installationsanweisungen 8
Instrucciones de instalación 10
Installationsvejledning 12
Installeringsinstruksjoner 14
Installationsinstruktioner 16
Garmin
®
and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. GC
™
is a trademark of Garmin Ltd. or its subsidiaries. These trademarks may not be
used without the express permission of Garmin.
Pozidriv
®
is a trademark of the American Screw Company.
June 2019
190-02485-90_0B
GC
™
200 IP Marine Camera
Installation Instructions
Mounting Considerations
WARNING
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
You can mount the camera upside-down or sideways. You can
reverse the camera image to use in rearview mode. See your
chartplotter owner's manual for instructions.
NOTE: You must update your chartplotter software to setup and
view the camera feed on your chartplotter.
• You must mount the camera in a location where it is not
submerged, does not present a hazard in doorways or
walkways, and cannot be damaged by docks, pilings, or other
pieces of equipment.
• You should mount the camera in a location strong enough to
support the weight of the device and where you can remove
the camera.
• You should mount the camera so the LED is visible and the
cables can be connected easily.
• To avoid interference with a magnetic compass, do not
mount the camera closer to a compass than the compass-
safe distance value listed in the product specifications.
• You should test the camera in the selected location before
you permanently mount the camera.
• You can use the Garmin
®
Power Module to help make the
installation easier. The Power Module uses a single camera
cable instead of separate power and ethernet cables. This is
especially beneficial when the camera is located far away
from other electronics, such as near the bow or on a mast.
Tools Needed
• Drill and 2 mm (
1
/
16
in.) drill bit
• Pozidriv
®
screwdriver
Mounting the Camera
1
Secure the template to the mounting location.
2
Using a 2 mm (
1
/
16
in.) drill bit, drill the pilot holes.
3
Using the included hex wrench, loosen the screw in the side
of the camera base.
4
Remove the base from the camera body.
5
Feed the camera cables through the camera base, or through
one of the cable channels.
6
Align the camera base with the pilot holes, and secure the
camera base with the washers and screws .
7
Attach the camera to the base, and tighten the screw in
the camera base.
8
Connect the camera cables.
9
Align the slots on the camera base with the collar lugs ,
and turn the collar until it locks.
Connection Considerations
Connection Diagram with Direct Power
GC
™
200 marine IP camera
Garmin Marine Network cable small connector (included)
Garmin Marine Network Adapter Cable small to large (included)
9 to 18 Vdc power source (not included)
NOTICE
To avoid permanently damaging the camera, do not connect the
camera directly to a 24 Vdc system. You must use a Garmin Power
Module when connecting to a 24 Vdc system.
1 A fast-acting fuse (required, not included)
NOTICE
You must connect the power wire through a 1 A fast-acting fuse
(not included). Without a fuse, the device can malfunction.
Garmin chartplotter (not included)
Connection Diagram with a Garmin Power Module
GC 200 marine IP camera
Garmin Marine Network cable small connector
Power module (010-12527-00, not included)
In-line switch (not included)
9 to 32 Vdc power source (not included)
Chartplotter (not included)
2 Installation Instructions
Camera Status LED
LED Activity Status
Solid red The camera is on.
Solid green The camera is connected to the network and
transmitting data.
Flashing green The camera detects motion.
Specifications
Dimensions (Base W x H) 87 x 79 mm (3.4 x 3.1 in.)
Weight 520 g (1.2 lbs.)
Water rating IEC 60529 IPX7
1
Operating temperature range From -20 to 60°C (from 14 to 140°F)
Storage temperature range From -30 to 60°C (from -4 to 140°F)
Input voltage From 9 to 18 Vdc
Power module input voltage
(not included)
From 9 to 32 Vdc
Operating current with infrared
on
370 mA
Operating current with infrared
off
210 mA
Power consumption Max 5 W with infrared on
Fuse 1 A fast-acting (required for direct
power connection, not included)
Horizontal viewing angle 99.2 +/- 3 degrees
Vertical viewing angle 74 +/- 3 degrees
Infrared distance 30 m (98.4 ft.)
Compass-safe distance 10 cm (4 in.)
1
The device withstands incidental exposure to water of up to 1 m for up to 30 min. For more information, go to
www.garmin.com/waterrating.
Installation Instructions 3
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
© 2018 Garmin Ltd. or its subsidiaries
support.garmin.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18

Garmin GC™ 200 Marine IP Camera Owner's manual

GC™ 200 Marine IP Camera
Garmin
Brand
Garmin
Model
GC™ 200 Marine IP Camera
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents