Garmin GC 100 tradlos kamera Operating instructions

Brand: Garmin

Model: GC 100 tradlos kamera

Type: Operating instructions

™

100

INSTALLATION

INSTRUCTIONS

Getting Started

WARNING

See the Important Safety and Product Information guide in the

product box for product warnings and other important

information.

Mounting Considerations

• You must mount the camera in a location where it is not

submerged.

• You should mount the camera within 76 m (250 ft.) of a

chartplotter. The range depends on your installation location

and obstacles between the camera and the chartplotter. If the

camera is out of range of the chartplotter due to obstacles or

distance, you must reposition the camera.

• You should test the camera in your desired location before

you permanently mount the camera.

• You should mount the camera so that the cable can be

connected easily.

• You should mount the camera in a location where it cannot

be damaged by docks, pilings, or other pieces of equipment.

• You should mount the camera so it does not present a

hazard in doorways or walkways.

• You should mount the camera in a location where you can

remove the camera.

Mounting the Camera

Using a 3.2 mm (

in.) drill bit, drill a pilot hole.

NOTE: If you are mounting the camera onto fiberglass, it is

recommended to use a countersink bit to drill a clearance

counterbore through the top gelcoat layer only, but no

deeper. This will help to avoid cracking the gelcoat layer

when the screws are tightened.

Using the included screw, fasten the camera mount to the

mounting surface.

Insert the camera into the housing .

Close the front of the housing.

Tighten the tamper-proof side screws using the included tool.

Connect the power cable.

Connecting to Power

WARNING

When connecting the power cable, do not remove the in-line

fuse holder. To prevent the possibility of injury or product

damage caused by fire or overheating, the appropriate fuse

must be in place as indicated in the product specifications. In

addition, connecting the power cable without the appropriate

fuse in place voids the product warranty.

Route the power cable to the power source and to the device.

Connect the red wire to the positive (+) battery terminal, and

connect the black wire to the negative (-) battery terminal.

Pairing the GC 100 Camera with a Garmin

Chartplotter

Before you can connect a wireless device to the chartplotter

wireless network, you must configure the chartplotter wireless

network. See your chartplotter manual for information on

configuring the wireless network.

With the camera within an unobstructed 76 m (250 ft.) of the

chartplotter, quickly press three times.

On the chartplotter, select Settings > Communications >

Wireless Devices > Garmin Camera > Start.

Follow the on-screen instructions.

Turning the Camera Off

Hold for 3 seconds.

NOTE: If you hold for more than 10 seconds, the camera

resets.

Specifications

Water rating IEC 60529 IPX6/IPX7

Operating temperature range From -20 to 60°C (from -4 to 140°F)

Charging temperature range From 0 to 45°C (from 32 to 113°F)

Storage temperature range From -40 to 85°C (from -40 to 185°F)

Input voltage From 10 to 30 Vdc, 1.5 A max.

Compass-safe distance 10 cm (4 in.)

Wireless frequency and protocol 2.4 GHz @ 17 dBm nominal

GC 100 Blink Codes

After the camera is installed and paired with the chartplotter, the

camera turns on when the chartplotter is turned on. The color

and blink sequence of the status LED on the camera indicates

its operational status.

LED

Color

LED State Status

Green Three blinks The camera is turning on.

Red Three blinks The camera is turning off.

The device withstands incidental exposure to water of up to 1 m for up to 30 min.

For more information, go to www.garmin.com/waterrating.

TA-2018/1686

TRA

REGISTERED No:

ER62993/18

DEALER No:

DA0015955/08

GUID-954A35F6-710F-4D78-93CD-48DD69D26558 v4February 2020

LED

Color

LED State Status

Blue One blink per second for up to

two minutes, or until the

camera connects to a

chartplotter

The camera is attempting to

connect to a chartplotter

using Wi‑Fi

Amber One blink per second until the

camera powers down or the

battery is charged

The camera battery is not

charged sufficiently to

stream video.

Garmin

and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries,

registered in the USA and other countries.

™

is a trademark of Garmin Ltd. or its

subsidiaries. These trademarks may not be used without the express permission of

Garmin.

Wi‑Fi

is a registered mark of Wi-Fi Alliance Corporation.

support.garmin.com

Garmin GC 100 tradlos kamera Operating instructions

Garmin GC 100 tradlos kamera Operating instructions

Garmin GC 100 tradlos kamera Operating instructions

Related papers

Other documents