Foster Solo Plus Sercie Manual

S e r v i c e M a n u a l

Solo Plus

Units 2001

PART 1A

Wall Mount Units

Ceiling Mounted Units

DIMENSIONS

Solo Plus DRWG 1 d + e

N

J

H

I

MODEL CONDENSER UNIT EVAPORATOR UNIT PLUG SIZE CUT-OUT SIZE

A x B x C (mm) G x E x F (mm) W x H (mm) W X H (mm)

H x J x K (mm) I x M x N (mm)

SP 1 HC 620 x 719 x 357 545 x 150 x 332 545 x 332 550 x 337

SP 2 H & LC 620 x 719 x 357 545 x 150 x 332 545 x 332 550 x 337

SP 3 H & LC 820 x 809 x 390 745 x 150 x 332 745 x 332 750 x 337

SP 4 HC 820 x 809 x 390 745 x 150 x 332 745 x 332 750 x 337

SP 4 LC 820 x 929 x 427 745 x 220 x 452 745 x 452 750 x 458

SP 5 HC 820 x 929 x 427 745 x 220 x 452 745 x 452 750 x 458

1

Mod. A B C D E F G

SP101LW, SP101HW

735 264 790 400 280 510 368

SP201HW, SP301HW

SP201LW, SP401HW

830 264 790 620 280 510 585

SP501HW

SP301LW, SP601HW 830 364 982 620 350 632 585

2

2. SOLO PLUS TECHNICAL DATA

Foster Nom. HP Cut Out HP Cut In Suction Valve Noise Heat Rejected RoomVent 32°C Ambient 43°C Ambient Air Air Vol Electrical Nominal Defrost Condensate Net Gross

Model No. HP Press Bar Press Bar Press Bar Level dBa Max Watts @ 32°C

m

3

/ h # Watts Room Cap Watts Room Cap Throw mts m

3

/ h

Volts

Phase

Hz

Amps Watts Type Vaporisation Wt. Kg Wt. Kg

NOTE: The condenser fan pressure stat ﬁtted on Low Ambient units should be set at 17bar with a 1.5bar differential, this applies to high and low temperature models.

SP 101HW 0.375 28 23 ------ 58 1900 700 1300 11 1160 8 4 600 230 1 50 3.9 600 Hot Gas Auto 53 74

SP 201HW 0.5 28 23 ------ 60 2050 700 1450 13 1200 11 4 600 230 1 50 5.5 600 Hot Gas Auto 56 77

SP 301HW 0.75 28 23 ------ 60 2700 700 1800 16 1550 14 4 600 230 1 50 5.6 900 Hot Gas Auto 64 85

SP 401 HW 0.75 28 23 ------ 60 3650 1400 2550 25 2200 20 4 1200 230 1 50 7 1100 Hot Gas Auto 80 110

SP 501HW 1 28 23 ------ 62 5100 1400 3100 33 2700 27 4 1200 400 3 50 5.2 1800 Hot Gas Auto 80 110

SP 601HW 1.5 28 23 ------ 63 6900 1500 4700 58 4000 48 9.5 1800 400 3 50 5.9 2200 Hot Gas Auto 100 135

STORAGE TEMP +10°C

Foster Ref Qty Capillary Size

Model No. Gas Grms No. x Dia x Len

SP 101HW R404A 0.67 1 x 1.5 x 2500

SP 201HW R404A 0.67 1 x 1.5 x 2500

SP 301HW R404A 0.64 1 x 1.8 x 2000

SP 401HW R404A 1.10 1 x 2.0 x 2900

SP 501HW R404A 0.88 2 x 1.8 x 2500

SP 601HW R404A 1.11 2 x 2.0 x 2000

Foster Nom. HP Cut Out HP Cut In Suction Valve Noise Heat Rejected RoomVent 32°C Ambient 43°C Ambient Air Air Vol Electrical Nominal Defrost Condensate Net Gross

Model No. HP Press Bar Press Bar Press Bar Level dBa Max Watts @ 32°C

m

3

/ h # Watts Room Cap Watts Room Cap Throw mts m

3

/ h

Volts

Phase

Hz

Amps Watts Type Vaporisation Wt. Kg Wt. Kg

SP 101HW 0.375 28 23 ------ 58 1650 700 1050 7 900 6 4 600 230 1 50 3.9 600 Hot Gas Auto 53 74

SP 201HW 0.5 28 23 ------ 60 1756 700 1150 9 1050 7 4 600 230 1 50 5.5 600 Hot Gas Auto 56 77

SP 301HW 0.75 28 23 ------ 60 2356 700 1450 13 1300 10 4 600 230 1 50 5.6 900 Hot Gas Auto 64 85

SP 401 HW 0.75 28 23 ------ 60 3000 1400 1900 20 1600 14 4 1200 230 1 50 7 1100 Hot Gas Auto 80 110

SP 501HW 1 28 23 ------ 62 4500 1400 2700 30 2350 24 4 1200 400 3 50 5.2 1800 Hot Gas Auto 80 110

SP 601HW 1.5 28 23 ------ 63 6300 1500 4100 50 3300 35 9.5 1800 400 3 50 5.9 2200 Hot Gas Auto 100 135

Foster Nom. HP Cut Out HP Cut In Suction Valve Noise Heat Rejected RoomVent 32°C Ambient 43°C Ambient Air Air Vol Electrical Nominal Defrost Condensate Net Gross

Model No. HP Press Bar Press Bar Press Bar Level dBa Max Watts @ 32°C

m

3

/ h # Watts Room Cap Watts Room Cap Throw mts m

3

/ h

Volts

Phase

Hz

Amps Watts Type Vaporisation Wt. Kg Wt. Kg

SP 101HW 0.375 28 23 ------ 58 1450 700 850 6 750 5 4 600 230 1 50 3.9 600 Hot Gas Auto 53 74

SP 201HW 0.5 28 23 ------ 60 1550 700 950 7 850 6 4 600 230 1 50 5.5 600 Hot Gas Auto 56 77

SP 301HW 0.75 28 23 ------ 60 2100 700 1300 11 1200 9 4 600 230 1 50 5.6 900 Hot Gas Auto 64 85

SP 401 HW 0.75 28 23 ------ 60 2800 1400 1700 15 1400 11 4 1200 230 1 50 7 1100 Hot Gas Auto 80 110

SP 501HW 1 28 23 ------ 62 4100 1400 2300 21 2000 17 4 1200 400 3 50 5.2 1800 Hot Gas Auto 80 110

SP 601HW 1.5 28 23 ------ 63 5550 1500 3350 36 2800 26 9.5 1800 400 3 50 5.9 2200 Hot Gas Auto 100 135

Foster Nom. HP Cut Out HP Cut In Suction Valve Noise Heat Rejected RoomVent 32°C Ambient 43°C Ambient Air Air Vol Electrical Nominal Defrost Condensate Net Gross

Model No. HP Press Bar Press Bar Press Bar Level dBa Max Watts @ 32°C

m

3

/ h # Watts Room Cap Watts Room Cap Throw mts m

3

/ h

Volts

Phase

Hz

Amps Watts Type Vaporisation Wt. Kg Wt. Kg

SP 101LW 1.25 28 23 2.5 62 1950 700 1050 7 850 5 4 600 230 1 50 5.2 900 Hot Gas Auto 64 85

SP 201LW 1.5 28 23 2.5 63 3200 1400 1700 14 1400 10 4 1200 400 3 50 4.3 1500 Hot Gas Auto 80 110

SP 301LW 2.2 28 23 2.5 63 4440 1500 2700 28 2250 20 9.5 1800 400 3 50 4.5 1700 Hot Gas Auto 105 140

Foster Ref Qty Capillary Size

Model No. Gas Grms No. x Dia x Len

SP 101HW R404A 0.67 1 x 1.5 x 2500

SP 201HW R404A 0.67 1 x 1.5 x 2500

SP 301HW R404A 0.64 1 x 1.8 x 2000

SP 401HW R404A 1.10 1 x 2.0 x 2900

SP 501HW R404A 0.88 2 x 1.8 x 2500

SP 601HW R404A 1.11 2 x 2.0 x 2000

Foster Ref Qty Capillary Size

Model No. Gas Grms No. x Dia x Len

SP 101HW R404A 0.67 1 x 1.5 x 2500

SP 201HW R404A 0.67 1 x 1.5 x 2500

SP 301HW R404A 0.64 1 x 1.8 x 2000

SP 401HW R404A 1.10 1 x 2.0 x 2900

SP 501HW R404A 0.88 2 x 1.8 x 2500

SP 601HW R404A 1.11 2 x 2.0 x 2000

STORAGE TEMP +10°C STORAGE TEMP +1/4°C STORAGE TEMP 0/-2°C

STORAGE TEMP +1/4°C

STORAGE TEMP 0/-2°C

STORAGE TEMP -18/-21°C

Foster Ref Qty Capillary Size

Model No. Gas Grms No. x Dia x Len

SP 101LW R404A 0.53 1 x 1.5 x 2500

SP 201LW R404A 0.84 1 x 1.8 x 2500

SP 301LW R404A 1.13 2 x 1.6 x 2800

STORAGE TEMP -18/-21°C

3. ACCESS TO THE UNIT COMPARTMENT / EVAPORATOR HOUSING

WALL MODEL

Front Panel: Grasp each side of the front panel and “pull forward” releasing it from the spring clips located

down each edge,it may be necessary to separate the front panel from the main body using a ﬂat

blade screwdriver and gently ease away.

Condenser Fan After removing the front panel “pull upwards” the fan housing assembly releasing it from

Assembly: the 4 “spring clips” located in each corner, it may be necessary to separate the fan housing

assembly from the main body using a ﬂat blade screwdriver and gently ease away.

Evaporator Fan Remove the screw securing the drain tube to the drip tray and remover the drain tube.

Remove the four screws securing the drain pan and remove.

Remove the three remaining screws securing the side panel and remove it allowing access into

the evaporator fan assembly.

4. CONTROLLER OPERATION

DESCRIPTION OF ELECTRONIC PANEL

5

9

10

6

1

2

4

3

8

7

3

1) CONTROL LED (Green):

Lit: Compressor running, unit is refrigerating. FLASHING: Compressor is in start delay mode

(waiting for signal to start) OFF: Compressor is OFF. Room is down to set temperature.

2) CONTROL LED (Green):

LIT: Evaporator fan(s) running. FLASHING: Evaporator fan(s) in start delay mode (waiting for

signal to start ) OFF: Evaporator fan (s) OFF

3) Control LED (Yellow):

LIT: Unit in defrost mode (auto or manual)

Flashing Evaporator drip time with compressor and evaporator fan off.

4) ALARM LED (Red):

LIT: Alarm is active – see separate ALARMS section. OFF: Unit is functioning normally

5) DISPLAY:

When connected to the mains the display will read OFF indicating the condition of the unit. By

pressing the ON/OFF key for 3 seconds the unit will turn ON and display the room temperature.

During programming mode the various parameters will be displayed and during alarm mode an

alarm code will be displayed.

6) SET/ESC KEY:

Pressed for 3 seconds, the led is lit and setting of required room temperature is enabled. During

programming it is used to pass from a sub menu to an upper one.

7) DOWN/ ROOM LIGHT KEY:

During programming mode or setting of room temperature it serves to reduce the display value.

At other times it serves to control the room light.

8) DEFROST/ UP KEY:

By pressing for more than 4 seconds it activates a manual defrost. During programming mode or

setting of room temperature it serves to increase the displayed value.

9) ON/OFF KEY:

To turn the unit ON or OFF press and hold for more than 3 seconds.

10) ENTER KEY:

Permits access to the programming menu and passage to the sub menu. Access to this programming

mode should be by qualiﬁed persons only.

°C

4

5

6

7

8

CONTROLLER ALARMS AND FAULT FINDING.

When an alarm condition occurs the unit will display an alarm code ERR (this will differ according to the nature of

the alarm):

• Alarm LED will illuminate (4)

• Buzzer will sound (if remote alarm is ﬁtted)

• The alarm relay (for remote alarms) will be energised.

The pressing of any key will mute the alarm buzzer.

When the alarm is muted the LED will continue to ﬂash for as long as the alarm condition persists.

To display the alarm code it is necessary to enter the alarm menu:

Press the ENTER key (10) for more than three seconds. FnC will be displayed. Press the DEFROST/UP key (8)

until AL is displayed and then press ENTER (10). At this point the alarm code will be displayed indicating the nature

of the alarm.

High Temperature Alarm (HI)

The red LED, buzzer and remote alarm relay are activated; the alarm code HI is displayed in the Alarm Menu.

The cause can be:

• Product to warm

• Excessive door openings

• Excessive product load

• Unit malfunction

Low Temperature Alarm (LI)

The red LED, buzzer and remote alarm relay are activated; the alarm code LI is displayed in the Alarm Menu.

The cause can be:

• Malfunction of the electronic controller

High Pressure Alarm (EO)

Each time the pressure switch trips, the buzzer and red LED are activated. If more than ten trips occur during a

1-hour period then the unit will shut down automatically. The remote relay will be activated and the label

ERR will

ﬂash on the display alternating with the room temperature. The alarm code EO is displayed in the Alarm Menu.

The cause can be:

• Dirty condenser

• Condenser fan not running

• Front cover not ﬁtted

• Obstructed condenser air inlet

• Obstructed condenser air outlet

• Inadequate ventilation

Voltage Monitor Alarm (E8 – only when ﬁtted as an option)

The optional voltage monitor is an electronic device that checks the units’ electrical supply. Should the voltage vary

by +/- 12% the unit will shut down for a period of 6 minutes (not adjustable) before attempting to re-start automatically

providing the voltage has returned to within limits. The red LED, buzzer and remote alarm relay are activated; the

label ERR will ﬂash on the display alternating with the room temperature. The alarm code E8 is displayed in the

alarm menu.

WARNING: if the Voltage monitor is ﬁtted it is important to note that on start up it has a time delay of seven minutes,

during this period the power should be on with the controller in the OFF position.

Room Sensor Fault (E1)

The red LED, buzzer and remote alarm relay are activated; the label ERR will ﬂash on the display alternating with

the room temperature: alarm code E1 in the alarm menu.

Possible causes are:

•

Faulty room sensor.

• Room sensor terminals badly connected.

9

Defrost sensor fault (E2)

The red LED, buzzer and remote alarm relay are activated; the label ERR will ﬂash on the display alternating with

the room temperature: alarm code E2 in the alarm menu.

Possible causes are:

•

Faulty defrost sensor

• Defrost sensor terminals badly connected.

Condenser Sensor Fault (4)

The red LED, buzzer and remote alarm relay are activated; the label

ERR will ﬂash on the display alternating with

the room temperature: alarm code E4 in the alarm menu.

Possible causes are:

•

Faulty condenser sensor

• Condenser sensor terminals badly connected.

Condenser Temperature Alarm (H4)

If the condensing temperature exceeds the factory pre set value (not adjustable) the red LED, buzzer and remote

alarm relay are activated: The alarm code H4 is displayed in the alarm menu.

Possible causes are:

•

Dirty condenser

• Condenser fan not running

• Front cover not ﬁtted

• Obstructed condenser air inlet

TROUBLE SHOOTING

1) Compressor stops. There is an internal over temperature device (Klixon) that stops the compressor each time the

admissible temperature of the motor windings is exceeded.

Possible causes are:

• Insufﬁcient ventilation to the compressor

• Mains voltage anomaly

• Faulty condenser fan

The device will re-set automatically when the windings cool down.

2) Formation of ice on evaporator coil impeding airﬂow.

Possible causes are:

• Excessive door openings

• Door left open for long periods

• Evaporator fan/s faulty

• Door switch faulty (if ﬁtted)

• Faulty defrost heater (if ﬁtted)

• Faulty hot gas solenoid valve (if ﬁtted)

• Pre set defrost routine not sufﬁcient to clear evaporator of ice build up.

• Decrease the time interval between defrosts.

3) Display does not illuminate.

• Is their power to the unit?

• Is the mains cable connected correctly?

• Have the fuses in the electrical panel blown?

7. PARAMETER LIST

10

Medium Low

Label Description

Unit of

Range

Hot gas Hot gas

measure defrost defrost

dro Display Readout °C or °F ( 0=°C. 1=°F) Flag 0 or 1 0 0

CA1 Calibration of room sensor °C -12 to +12 0 0

Compressor rE1 menu. coP

diF Differential °C/1 2 2 2

HSE Maximum set point °C/1 LSE to 150 10 -15

LSE Minimum set point °C/1 -50 to HSE -5 -25

dbi Time delay between 2 compressor starts Minutes 0 to 15 2 2

dOF Time delay between compressor OFF and next start Minutes 0 to 15 2 2

Ont Compressor ON time if room sensor fails Minutes 0 to 250 10 10

OFt Compressor OFF time if room sensor fails Minutes 0 to 250 20 20

Defrost rE2 menu. dEF

dit Time interval between 2 defrosts Hour 0 to 31 3 3

dEt Defrost time override Minutes 1 to 250 20 20

dCt Defrost interval time count mode Number 0 to 3 0 0

0 = compressor run time

1 = unit run time

2 = each time compressor stops

3 = determined on a real time basis

dtY Defrost type selection Number 0 to 3 2 2

0 = Timed defrost

1 = Electric defrost

2 = hot gas

3 = Off cycle

dt Drain down time Minutes 0 to 250 2 2

dSt Defrost termination temperature °C/1 -50 to 150 15 15

Evaporator Fans rE3 menu. FAn

Fdt Fan delay time Minutes 0 to 15 3 3

FCO Evaporator fan/s run with compressor Flag n / y n n

dFd Fan/s stops during defrost Flag n / y y y

Fod Fan/s off when door opened Flag on/off on on

FSt Fan stop temperature °C/1 -50 to 150 50 50

Room Light rE4 menu. LUc

No parameters

Temperature Alarms rE5 menu. ALP

LAL Low temperature alarm °C/1 -50 to HAL -5 -5

HAL High temperature alarm °C/1 LAL to 150 5 5

AFd Alarm differential °C/1 -12 to 12 2 2

PAO Alarm delay after start-up Hour 0 to 10 3 6

dAo Alarm delay after defrost Minutes 0 to 250 60 60

OAO Alarm delay after door opening Hour 0 to 10 1 1

Pressure alarms rE6 menu. PP

PEi Time period for pressure trips Minutes 1 to 99 60 60

Pen Numbers of pressure trips Number 0 to 15 10 10

Condensing temperature alarms rE7 menu. ALP

HAL Maximum condensing temperature alarm setpoint °C/1 0 to 99 55 55

AFd Alarm differential °C/1 -12 to 12 2 2

Fig 1.

8. ELECTRICAL CONNECTIONS

The unit operates from a 220/240v1-50hz or a 400v- 3-50hz electrical supply as denoted in the technical data.

For 60hz application consult Foster.

The selection of mains cable depends on the unit (Amps) and on the siting of the cable itself.

The installer will therefore evaluate the most suitable one on a case by case basis.

The table below gives a rough sizing and should be used as a guide only

Unit Amps Cable diameter

Up to 12 Amps 1.5mm

2

12 to 17 Amps 2.5mm

2

Over 17 Amps 4mm

2

Remove the front panel of the unit and connect the cables to the terminal box as per the diagrams in ﬁg 1,2,3 and 4.

11

Single Phase Unit

L1 – Brown

N – Blue

PE – yellow / green

BR BL YG

L 1

N

PE

Mains Supply Cable

230V/ three phase unit without neutral.

L1 – Brown L2 – Black

L3 – Blue

PE – yellow / green

BR BLK BL YG

L 2

L 3

N

Mains Supply Cable

Fig 2.

PE

400V/ three phase unit with neutral.

L1 – Brown L2 – Black

N – Blue L3 – Black

PE – yellow / green

BR BLK BLK BL YG

L 2

L 3

N

Mains Supply Cable

Fig 3.

PE

L 1

Connections for options

1 = Brown 5 = Brown

2 = Blue 6 = Blue

3 = Brown

4 = Blue

= yellow/green

BR BL BR BL GV BR BL

Fig 4.

6

Door Heater

Remote Alarm Cable

5

1

2

3

4

Door Microswitch

PE

9. PROBE RESISTANCE VALUES

The air and defrost probes have the following temperature resistance values (K ohms)

Temperature Kohms Temperature Kohms

+50°C 4,161 0°C 27,280

+40°C 5,828 -10°C 42,450

+30°C 8,313 -20°C 67,740

+20°C 12,090 -30°C 111,300

+10°C 17,960 -40°C 188,400

10. FUSE RATINGS

NOTE: LA refers to Low Ambient Models

FOSTER CODE Internal fuse Wiring diagram

SP101HW 16 A J1018

SP201HW 16 A J1018

SP301HW 20 A J1018

SP401HW 25 A J1018

SP501HW No fuses J2020

SP601HW No fuses J2019

SP101LW 20 A J1018

SP201LW No fuses J2019

SP301LW No fuses J2019

SP101HW LA 16 A J1019

SP201HW LA 16 A J1019

SP301HW LA 20 A J1019

SP401HW LA 25 A J1019

SP501HW LA No fuses J2021

SP601HW LA No fuses J2022

SP101LW LA 20 A J1019

SP201LW LA No fuses J2022

SP301LW LA No fuses J2022

12

11. WIRING DIAGRAMS

ROOM SENSOR

CONDENSER ALARM SENSOR

DEFROST SENSOR

SPEED REGULATOR

SPEED REGULATOR SENSOR

DEFROST HEATER

RESISTENZA CARTER COMPRESSORE

COMPRESSOR CRANKCASE HEATER

DOOR HEATER CIRCUIT

CONTROL BOARD HEATER

VOLTAGE REGULATOR HEATER

CONDENSATE DRAIN HEATER

VOLTAGE REGULATOR FUSE

COMPRESSOR FUSE

ELECTRONIC CONTROL CAB

AUXILIARY FUSE

ROOM LIGHT FUSE

VOLTAGE REGULATOR

13

BA

BC

BS

BVR

BVRS

E

E1

M1

EP

ER1

ER2

ES

F13

F1

F1E

FL

F20

FM

EMERGENCY ‘STAT

ALARM

CONTACTOR

DEFROST CONTACTOR

COMPRESSOR MOTOR Nr.1

DOOR MICROSWITCH(ROOM)

CONDENSER FAN MOTOR

EVAPORATOR FAN MOTOR

COND. FAN STARTING PRESSURE SWITCH

L/P SWITCH

H/P SWITCH

MAIN SWITCH

COND. FAN SPEED REGULATOR

“OFF” SWITCH

TRANSFORMER

TERMINAL BOARD-CONNECTOR

REFRIGERANT SOLENOID

HOT GAS SOLENOID

FTE

HI

K1

K11

M1

MPC

MVC

MVE

P1MX

PMI

PMX

Q1

Q3

T

X

YS

YG

COMPONENT IDENTIFICATION

14

SUPPLY

400V/3N-/50Hz

Colour Code

MA - BROWN

BL - BLUE

GV - GREEN/YELLOW

NE - BLACK

Drawing No. Sheet No.

J2020 1 of 1

Drawn By Approved Date

Title

SP501HW

FOSTER REFRIGERATOR - A Division of ITW

Ltd.

15

LOW TEMP ONLY

SUPPLY

230-220V/1N-/50Hz

Colour Code

MA - BROWN

BL - BLUE

GV - GREEN/YELLOW

NE - BLACK

Drawing No. Sheet No.

J1018 1 of 1

Drawn By Approved Date

Title

SP101LW

SP101HW

SP201HW

SP301HW

FOSTER REFRIGERATOR - A Division of ITW

Ltd.

SP101LW

SPE

16

SUPPLY

400V/3N-/50Hz

Colour Code

MA - BROWN

BL - BLUE

GV - GREEN/YELLOW

NE - BLACK

Drawing No. Sheet No.

J2019 1 of 1

Drawn By Approved Date

Title

SP201LW

SP301LW

SP601HW

FOSTER REFRIGERATOR - A Division of ITW

Ltd.

PART 1B

Ceiling Mounted Solo January 2003 Controller Settings

Dimensions

Description

1. Condensing unit and Evaporator (evaporator plaed in an insulated box) located outside of the coldroom.

2. Air inlet and outlet to the evaporator located inside the coldroom.

3. Electrical control panel located in the condensing unit enclosure.

4. Wall mounted control panel.

A B C D E F G H I L M X Y

SP1/SP2 357 250 719 340 122 28 332 506 60 620 545 337 550

SP3/SP4 390 250 809 360 122 28 332 540 60 820 745 337 750

SP5 427 250 929 410 122 98 452 645 60 820 745 458 750

17

WALL MOUNT SOLO PLUS TECHNICAL DATA

Foster Nom. HP Cut Out HP Cut In Suction Valve Noise Heat Rejected RoomVent 32°C Ambient 43°C Ambient Air Air Vol Electrical Nominal Defrost Condensate Net Gross

Model No. HP Press Bar Press Bar Press Bar Level dBa Max Watts @ 32°C

m

3

/ h # Watts Room Cap Watts Room Cap Throw mts m

3

/ h

Volts

Phase

Hz

Amps Watts Type Vaporisation Wt. Kg Wt. Kg

NOTE: Noise levels taken in a room with a concrete ﬂoor, no sound attenuation and ceiling height of 7 metres with the unit base 1.5 metres from ﬂoor level, installed in a coldroom and the Sound Metre 3 metres distance.

SP 1HC 0.625 28 23 ———- 59 2300 750 1550 10 1400 7 3 550 230 1 50 4.4 700 Hot Gas Auto 59 90

SP 2HC 0.75 28 23 ———- 60 2675 750 1750 12 1600 10 3 550 230 1 50 5.2 800 Hot Gas Auto 59 90

SP 3HC 1 28 23 ———- 60 3750 1400 2600 20 2200 16 3.5 1100 230 1 50 6.9 1100 Hot Gas Auto 74 114

SP 4HC 1.2 28 23 ———- 60 4200 1400 2900 28 2700 22 3.5 1100 400 3 50 4.4 1500 Hot Gas Auto 75 115

SP 5HC 2 28 23 ———- 63 7200 5200 5200 56 4600 48 6 2300 400 3 50 5.1 2100 Hot Gas Auto 93 139

STORAGE TEMP +10°C

Foster Ref Qty Capillary Size

Model No. Gas Grms No. x Dia x Len

SP 1HC R404A 0.54 1 x 1.63 x 2200

SP 2HC R404A 0.60 1 x 1.83 x 3100

SP 3HC R404A 0.73 2 x 1.38 x 3100

SP 4HC R404A 0.70 2 x 1.98 x 2900

SP 5HC R404A 1.10 2 x 1.98 x 2000

Foster Nom. HP Cut Out HP Cut In Suction Valve Noise Heat Rejected RoomVent 32°C Ambient 43°C Ambient Air Air Vol Electrical Nominal Defrost Condensate Net Gross

Model No. HP Press Bar Press Bar Press Bar Level dBa Max Watts @ 32°C

m

3

/ h # Watts Room Cap Watts Room Cap Throw mts m

3

/ h

Volts

Phase

Hz

Amps Watts Type Vaporisation Wt. Kg Wt. Kg

SP 1HC 0.625 28 23 ———- 59 1950 750 1150 7 1050 6 3 550 230 1 50 4.4 700 Hot Gas Auto 59 90

SP 2HC 0.75 28 23 ———- 60 2200 750 1350 9 1250 6 3 550 230 1 50 5.2 800 Hot Gas Auto 59 90

SP 3HC 1 28 23 ———- 60 2850 1400 1900 17 1600 10 3.5 1100 230 1 50 6.9 1100 Hot Gas Auto 74 114

SP 4HC 1.2 28 23 ———- 60 3350 1400 2300 20 2050 12 3.5 1100 400 3 50 4.4 1500 Hot Gas Auto 75 115

SP 5HC 2 28 23 ———- 63 5700 1500 4100 46 3600 28 6 2300 400 3 50 5.1 2100 Hot Gas Auto 93 139

Foster Nom. HP Cut Out HP Cut In Suction Valve Noise Heat Rejected RoomVent 32°C Ambient 43°C Ambient Air Air Vol Electrical Nominal Defrost Condensate Net Gross

Model No. HP Press Bar Press Bar Press Bar Level dBa Max Watts @ 32°C

m

3

/ h # Watts Room Cap Watts Room Cap Throw mts m

3

/ h

Volts

Phase

Hz

Amps Watts Type Vaporisation Wt. Kg Wt. Kg

SP 1HC 0.625 28 23 ———- 59 1750 750 1050 6 925 4 3 550 230 1 50 4.4 700 Hot Gas Auto 59 90

SP 2HC 0.75 28 23 ———- 60 2000 750 1200 7 1100 5 3 550 230 1 50 5.2 800 Hot Gas Auto 59 90

SP 3HC 1 28 23 ———- 60 2650 1400 1700 12 1450 9 3.5 1100 230 1 50 6.9 1100 Hot Gas Auto 74 114

SP 4HC 1.2 28 23 ———- 60 3150 1400 2000 15 1700 12 3.5 1100 400 3 50 4.4 1500 Hot Gas Auto 75 115

SP 5HC 2 28 23 ———- 63 5100 1500 3600 36 3200 17 6 2300 400 3 50 5.1 2100 Hot Gas Auto 93 139

Foster Nom. HP Cut Out HP Cut In Suction Valve Noise Heat Rejected RoomVent 32°C Ambient 43°C Ambient Air Air Vol Electrical Nominal Defrost Condensate Net Gross

Model No. HP Press Bar Press Bar Press Bar Level dBa Max Watts @ 32°C

m

3

/ h # Watts Room Cap Watts Room Cap Throw mts m

3

/ h

Volts

Phase

Hz

Amps Watts Type Vaporisation Wt. Kg Wt. Kg