Hukoro F14261-BK Operating instructions

Brand
Hukoro
Model
F14261-BK
Type
Operating instructions

This manual is also suitable for

Hukoro F14261-BK is a light fixture designed for both indoor and outdoor use. It comes with a glass shade and a rubber ring to prevent water from entering. The fixture can be attached to a junction box (not included) and secured with mounting screws. The electrical connection is made through wire nuts and secured with electrical tape. The fixture can accommodate one bulb (not included). Additional features include:

  • Safety glasses, ladder, electrical tape, Phillips screwdriver, flat blade screwdriver, pliers, wire strippers, mounting screws, and wire nuts are required for installation.
  • The mounting unit should be attached to the junction box using the provided mounting screws.

Hukoro F14261-BK is a light fixture designed for both indoor and outdoor use. It comes with a glass shade and a rubber ring to prevent water from entering. The fixture can be attached to a junction box (not included) and secured with mounting screws. The electrical connection is made through wire nuts and secured with electrical tape. The fixture can accommodate one bulb (not included). Additional features include:

  • Safety glasses, ladder, electrical tape, Phillips screwdriver, flat blade screwdriver, pliers, wire strippers, mounting screws, and wire nuts are required for installation.
  • The mounting unit should be attached to the junction box using the provided mounting screws.
*PARTS SHOWN MAY DIFFER SLIGHTLY PER LIGHT FIXTURE
EXPLODED PARTS INSTALLATION
STEP 1
Bulb
(not included)
Unscrew the ball nut and rubber ring from the mounting unit.
Use the mounting screws to attach the mounting unit
to the junction box (not included).
Fixture
Fixture
Nuts
Rubbre rings A
Glass Shade
Glass Shade
Shade
Shade
Mounting Unit
Mounting Unit
Mounting
Screws
Mounting
Screws
Junction Box
(not included)
Wire Nuts
Wire Nuts
Ball Nut
Ball Nut
Rubber Ring
Rubber Ring
Make the electrical connection from the junction box (not included) to the
fixture. Connect the ground wire to the mounting unit using the preinstalled
green ground screw. Next, connect the positive, negative and ground wires
with the supplied wire nuts. Secure with electrical tape.
STEP 2
White wire from
the fixture
Ground wire from
the Fixture
Black wire from
the fixture
Black or Red wire (hot)
from the junction box
White wire (neutral)
from the junction box
Bare or Green ground wire
from the junction box
*Green Ground Screw
*Sealing tape
(not included)
Wire
strippers
Ladder Safety
glasses
Electrical
tape
Phillips
screwdriver
Flat blade
screwdriver Pliers
CAUTION
Inspect the wire insulation for any cuts,
abrasions, or exposed copper that may have
resulted during shipping. If there is a defect
in the wire, do not attempt installation.
Before starting installation of this fixture or
removal of a previous fixture, disconnect the
power by turning off the circuit breaker or by
removing the fuse at the fuse box.
If you need further assistance, please contact us by Email: [email protected]
ASSEMBLY INSTRUCTIONS
TOOLS REQUIRED
HARDWARE INCLUDED
@
Attach the fixture to the mounting unit through screw holes
as shown, and secure it with rubber ring and ball nut.
ASSEMBLY INSTRUCTIONS INSTALLATION
STEP 4
STEP 5
STEP 3
Install bulb (not included).
Remove the rubbre rings A and nuts from the shade.
STEP 6
Attach the shade and Glass Shade to the fixture through
screw holes as shown, and secure it with rubber rings A
and nuts.
NOTICE: Please use caulk in the back plate and wall
mounting surface to prevent water from entering.
*junction box
(not included)
  • Page 1 1
  • Page 2 2

Hukoro F14261-BK Operating instructions

Brand
Hukoro
Model
F14261-BK
Type
Operating instructions
This manual is also suitable for

Hukoro F14261-BK is a light fixture designed for both indoor and outdoor use. It comes with a glass shade and a rubber ring to prevent water from entering. The fixture can be attached to a junction box (not included) and secured with mounting screws. The electrical connection is made through wire nuts and secured with electrical tape. The fixture can accommodate one bulb (not included). Additional features include:

  • Safety glasses, ladder, electrical tape, Phillips screwdriver, flat blade screwdriver, pliers, wire strippers, mounting screws, and wire nuts are required for installation.
  • The mounting unit should be attached to the junction box using the provided mounting screws.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents