Quoizel LWS4321A Installation guide

Brand
Quoizel
Model
LWS4321A
Type
Installation guide

Quoizel LWS4321A is a versatile lighting fixture designed to enhance the ambiance of any room. This stylish fixture features four arms that can be adjusted to direct light where you need it most. The included vintage-style bulbs emit a warm, inviting glow, creating a cozy and welcoming atmosphere. Installation is made simple with the provided mounting hardware and clear instructions. Whether you're looking to illuminate a living room, bedroom, or dining area, the Quoizel LWS4321A is an excellent choice for adding both style and functionality to your home.

Quoizel LWS4321A is a versatile lighting fixture designed to enhance the ambiance of any room. This stylish fixture features four arms that can be adjusted to direct light where you need it most. The included vintage-style bulbs emit a warm, inviting glow, creating a cozy and welcoming atmosphere. Installation is made simple with the provided mounting hardware and clear instructions. Whether you're looking to illuminate a living room, bedroom, or dining area, the Quoizel LWS4321A is an excellent choice for adding both style and functionality to your home.

AA
BB
CC
PART
DESCRIPTION
QUANTITY
AA Crossbar Assembly
1pc
3pcs
2pcs
Wire Connector
Outlet Box Screw
BB
CC
2018 QuoizelInc.
Model#
LWS4321A
Item# 1221056
1
Español p. 7
Français p. 4
Package Contents
Stock Part#
914156KIT
Tools Required
Bulb Recommended:
Estimated Assembly Time
Preparation
Quoizel Customer Service
(not included): Flathead screwdriver, Phillips screwdriver, Electrical
tape, Safety goggles, Ladder.
(1) 60W Type-S medium base vintage-style bulb, Alternate (1)
LED bulb.
: 20 - 30 minutes
:
Identify and inspect all parts before beginning installation
Check package contents list and diagrams below to be sure all parts are included.
If any parts are missing or damaged, do not attempt to assemble, install or operate
the fixture.
Contact for replacement parts.
·
·
·
·
·
·
·
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in
doubt.
These instructions are provided for your safety. It is very important you read them completely before installing
fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs.
- Make sure bulbs are given sufficient time to cool before removal.
- Do not subject glass parts to any shock while in operation or shattering may result.
Warnings And Cautions
6 Corporate Parkway
Goose Creek
SC 29445
Customer Service
Toll Free Phone
E-mail
:
1-844-564-3055
:
[email protected]
For the quickest
response, please visit
and
click on .
Quoizel.com
Contact Us
Thankyou for purchasing a Quoizel product.
Needassistance withparts orassembly?
CallQuoizel CustomerService tollfree at1-844-564-3055;
send us an email at[email protected] orvisit usonline atwww.quoizel.com
A
Socket Assembly
A
1pc
N/A
C
B
C
Shade
1pc
G14155SH
02.16.2019
B
Ring
1pc
D
M14176LBEK
Mounting Screw 3 pcs
D
2
Crossbar Assembly
Outlet Box Screw
Outlet Box
STEP 2:
a. Secure the crossbar to the outlet box (not included) with
outlet box screws.
b. Tighten until snug.
The preassembled mounting screws on the crossbar
should protrude outward.
Note:
STEP 3:
a. Remove mounting balls from the crossbar assembly.
b. Fit the ceiling canopy to the crossbar assembly and
secure with mounting balls.
The ceiling canopy should be snug against the
ceiling and the mounting balls.
If not, adjust the length of the mounting screws on the
crossbar assembly by unscrewing the preassembled hex
nuts.
Then, screw the mounting screws in or out of the crossbar
until the desired length is achieved.
Once the ceiling canopy is secure, remove the mounting
balls and ceiling canopy and proceed to Step 4.
Note:
?
?
?
Mounting
Screw
Hex Nut
Mounting Ball
Ceiling Canopy
STEP 4:
a. The lanyard is provided as a means to support the
fixture from the junction box while connecting the
electrical wires. This enables the fixture to hang from
the junction box and your hands are free to make the
wire connections.
b. Turn the button stop so it may be inserted into the
crossbar slot. Make sure the button stop is completely
inside the crossbar.
c. Slowly release the fixture to make sure it is supported
by the button stop.
d. Proceed to Step 5. Once wiring is complete, the lanyard
will push into the junction box when the Ceiling Canopy
is Attached to the ceiling.
Crossbar Assembly
Button Stop
Lanyard
Slot
2018 QuoizelInc.
STEP 1:
a. Unfold support arms of the fixture assembly to proper
locations. (Refer to Arm Orientation)
b. Remove Mounting Screw and Rubber Washer from bottom of
the socket assembly.
c. Place the ring over the edge of the shade.
d. Confirm that the holes on the shade align with the holes on the
ring.
e. align ring, shade and rubber washer with the ends of the side
arms of the socket assembly. Pass mounting screws through
ring, shade rubber washer and thread into side arm of the
socket assembly.
f. Hand-tighten until snug.
Arm Orientation
Socket Assembly
Ring
Shade
Mounting Screw
Rubber Washer
3
CARE AND MAINTENANCE
Wipe clean using soft, dry cloth or static duster. Always avoid using harsh chemicals and abrasives to clean
fixture as they may damage the finish.
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Bulbs will not light.
Fuse blows or the
circuit breaker trips
when light is turned
on.
1. Bulb is burned out.
2. Power is off.
3. Faulty wire connection.
4. Faulty switch.
Crossed wires or power wire is
grounding out.
1 . Replace light bulb.
2. Make sure power supply is on.
3. Check wiring.
4. Test or replace the switch.
Check wire connection.
STEP 6:
a. Install correct bulbs referring to fixture markings and/or labels for maximum wattage.
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
Printed in China
STEP 5:
a. Re-attach the ceiling canopy of the fixture body to the
crossbar assembly.
b. Secure with the previously removed mounting balls.
Mounting
Screw
Mounting Ball
Ceiling Canopy
WHITE
BLACK (OR RED) WIRE
WHITE OR RIBBED
BLACK OR SMOOTH
FROM SUPPLY
FROM SUPPLY
FROM FIXTURE
FROM FIXTURE
STEP 4:
* Use Wire Connectors (supplied) to connect the
wires.
ground wire green ground screw
ground screw
ground wire supply ground
supply white wire white fixture
supply wire
supply black (or red) black
fixture supply wire
a) Ground Wire:
1. Wrap supply around
on mounting bracket, no less than 2 in. from the end of
the wire. Tighten .
2. Connect fixture green to
wire with wire connector.
b) Supply Wire:
1. Connect the to the
with wire connector.
2. Connect the wire to the
with wire connector.
3. Wrap each connection with approved electrical tape
and carefully stuff all of the connected wires into the
outlet box.
GROUND WIRE
GROUND WIRE
FROM SUPPLY
FROM FIXTURE
GREEN GROUND SCREW
2018 QuoizelInc.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

Quoizel LWS4321A Installation guide

Brand
Quoizel
Model
LWS4321A
Type
Installation guide

Quoizel LWS4321A is a versatile lighting fixture designed to enhance the ambiance of any room. This stylish fixture features four arms that can be adjusted to direct light where you need it most. The included vintage-style bulbs emit a warm, inviting glow, creating a cozy and welcoming atmosphere. Installation is made simple with the provided mounting hardware and clear instructions. Whether you're looking to illuminate a living room, bedroom, or dining area, the Quoizel LWS4321A is an excellent choice for adding both style and functionality to your home.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents