Woodbridge F1018 Installation guide

R

WOODBRIDGE

R

WOODBRIDGE

R

WOODBRIDGE

R

WOODBRIDGE

R

WOODBRIDGE

R

WOODBRIDGE

R

WOODBRIDGE

R

WOODBRIDGE

www.woodbridgebath.com

200101 REV. 1

1

PREPARATION FOR INSTALLATION

ATTENTION! Dimensions may vary by up to 3/8". It is highly recommended to pull

all dimensions of actual model for installaon and measuring purposes.

ATTENTION! Measurements in inches are rouned to the nearest 1/8".

TECHNICAL DATA

Max ﬂow rate 4.6 GMP at 80 PSI

FREESTANDING FAUCET

R

WOODBRIDGE

Customer Service Phone: 562-229-0088. (Monday - Friday 9 AM - 5 PM Paciﬁc Time)

Or Email: [email protected]

31-3/4"

43-1/8"

33-7/8"

5-7/8"

1-5/8"

8-7/8"

3"

6-7/8"

2"

35-7/8"

59"

Max hand shower ﬂow rate 1.8 GPM AT 80 PSI

R

WOODBRIDGE

R

WOODBRIDGE

R

WOODBRIDGE

R

WOODBRIDGE

R

WOODBRIDGE

R

WOODBRIDGE

R

WOODBRIDGE

R

WOODBRIDGE

www.woodbridgebath.com 2

FREESTANDING FAUCET

PARTS & COMPONENTS

R

WOODBRIDGE

No

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

Component

Body

Screw

Canopy

Handle

Cap

Lock Nut

Cartridge

Take Over

Base Cover

Screw

Triangle Plank

Diverter Cartridge

Lock Nut

Diverter Handle

Hot and Cold Water Supply Line

Shower Hose

Hand Shower

TOOLS REQUIRED FOR INSTALLATION

OTHER TOOLS MAY BE REQUIRED

Basin Wrench Adjustable Wrench Teﬂon Tape Silicone Sealant Screwdriver

1

23

4

5

9

10

11

12

13

14

15

16

17

6

7

8

R

WOODBRIDGE

R

WOODBRIDGE

R

WOODBRIDGE

R

WOODBRIDGE

R

WOODBRIDGE

R

WOODBRIDGE

R

WOODBRIDGE

R

WOODBRIDGE

www.woodbridgebath.com 3

FREESTANDING FAUCET

R

WOODBRIDGE

INSTALLATION INSTRUCTIONS

Put the base cover over the take over.

1 2

3

Fix the faucet body to the take over.

4

Fix the screw posion

56

Screw the the take overto the Trangle Plank.

Install the Hot and Cold Water Supply Line now and ensure the

Hot and Cold Water Supply Line are hand ghtened into place.

(DO NOT USE SPANNER TO TIGHTEN AS IT CAN DAMAGE

THE O-RING). The Hot and Cold Water Supply Line are to be

ﬁed into the correct inlets for hot water and for cold water.

Connect another side of the Hot and Cold Water Supply Line

to the water supply pipe. Make sure they are to be ﬁed into

the correct outlets for hot water and cold water.

R

WOODBRIDGE

R

WOODBRIDGE

R

WOODBRIDGE

R

WOODBRIDGE

R

WOODBRIDGE

R

WOODBRIDGE

R

WOODBRIDGE

R

WOODBRIDGE

www.woodbridgebath.com 4

FREESTANDING FAUCET

R

WOODBRIDGE

Use the explosion screw to ﬁx the base on the ground. and

put the base cover over the Triangle Plank.

7

The installaon is completed.

Connect the shower hose and hand shower.

9

Aer installaon is complete, remove Spray head and rotate

handle to the close posion. Turn Water Supply Valves on,

and check all connecons for leak. Flush faucet by running

hot and cold water in full posion for one minute. Re ghten

the Spray.

10

8

Woodbridge F1018 Installation guide

Woodbridge F1018 Installation guide

Related papers

Other documents