R
R
V2.1
ITEM:FS-AZ0047**
03/03/2023
ANZZI Freestanding Tub Filler
V2.1-This version supersedes all previous versions as of 03/03/2023
PRODUCT SIZE CHART
TOOLS AND MATERIALS
PG.1
Wrench Marker Pen Drill 25/64"(10mm)
Drill Bit
2"Hole Saw
3/8 COMPRESSION
40.9
1040mm
41
1043mm
PG.2
Part Description Qty
[14] Gasket
[01] Spout
[02] Gasket
[03] Flow Regulator
[04] Faucet
[05] Check Valve
[06] Diverter
[07] Retainer(Diverter)
[08] Handle(Diverter)
[09] Screw
[10] Cap
[12] Hand Shower
[11] Post
[13] Check Valve
[15] Escutcheon
[16] Screw
[17] Anchor
[18] Expansion Screw
[19] Cartridge
[20] Retainer
[21] Cover
[22] Handle
[23] Inlet Hose
[24] Shower Hose
[25] Housing
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
3
1
1
1
1
2
1
1
Before installation:
1. Please check that all components are present.
2. Ensure that all supply lines are free of debris with supply stops installed.
3. Ensure water pressure is between 20-125 PSI.
4. If you are having difficulties on installation, please contact a professional plumber.
COMPONENT
[01]
[02]
[03]
[04]
[05]
[06]
[07]
[08]
[09]
[10]
[11]
[12]
[13]
[14]
[15]
[17]
[19] [20] [21] [22]
[09]
[10]
[23] [24]
[25]
[16]
[18]
INSTALLATION
12
PG.3
STEP 1:
Slide the Escutcheon [15] onto the Post [11].
STEP 2:
Install the to hand
tighten it. Secure the Screw on side by
Allen Key.
Anchor [17] the Post [11] and
[16]
[11]
[11]
[15]
[17]
[15]
[16]
INSTALLATION
PG.4
STEP 3:
the to the Faucet
and secure.
Install Inlet Hoses [23] [04]
Note: Makes sure to connect the Inlet Hose [23]
labeled “Hot” to the Faucet [04] inlet marked
“H” and the Inlet Hose [23] labeled “Cold” to the
Faucet [04] inlet marked “C”.
STEP 4:
Slide the Inlet Hose [23] through the Post [11]
and Install the Post [11] to the
Faucet [04] and tighten it.
the Anchor [17].
[04]
[23]
Hot Water Cold Water
[04]
[11]
3 4
[15]
[17]
56
2"
[51mm]
hole
marks of Anchor [17]
screw holes on the floor
mark of Anchor [17]
center point on the floor
25/64"
[10mm]
holes
Supply Lines with
3/8 compression
male threads
Inlet
Hose
STEP 5:
Position the Faucet [04] over the intended
installation spot. Mark the center point on
the floor. Then, mark the Anchor [17] screw
holes on the floor.
a.
b.
c.
Drill a 2” [51mm] hole into the floor, see Fig. 6.
Drill three 25/64” [10mm] holes into the concrete
floor. If floor is composed of wood, then there is no
need for drilling.
Connect the Inlet Hoses [23] to the water supply
lines (which should be protruding from the ground
and have matching male threading).
STEP 6:
Note: Make sure to connect the Inlet Hose [23] labeled
“Hot” to the hot water supply line and the Inlet Hose
[23] labeled “Cold” to the cold water supply line.
INSTALLATION
8
[11]
[17]
[04]
STEP 7:
a.Unscrew the Post [11].
b.Turn on hot and cold water supplies and check connections at arrows for leak
check for
leaks here
s.
c.
.
Connect the Post [11] to the Faucet [04] again. Tighten the Post [11] to secure.
[15]
Nut
Washer
[18]
STEP 8:
a-1. Install the Expansion Screws [18] for
concrete floor. Position the of
the faucet through the Expansion Screw [18],
slide the Washers onto the and
secure it by tighten the Nuts.
a-2. For the wooden floor, please secure the
faucet with #14 Phillips pan head
self-taping screws (not provided).
b. Slide the Escutcheon [15] to the floor to
cover the Anchor [17].
.
Anchor [17]
Anchor [17]
PG.5
INSTALLATION
9 10
[22][22]
[08][08]
[12][12]
[24][24]
[04][04]
STEP 9:
Install and secure the Hand Shower [12] and
Shower Hose [24] to the faucet as the figure
shows.
Note: Make sure there are washers between
the connections.
STEP 10:
Open the Handle [22], then turn the Handle
(Diverter) [08] to check the flow of spout and
hand shower. Check connections at arrows for
leaks. Retighten if necessary, but do not over
tighten.
PG .6
CLEANING & MAINTENANCE
1. To preserve the finish on the metallic parts of your ANZZI faucet, apply non-abrasive wax,
such as car wax. Any cleaners should be rinsed off immediately.
2. Clean the flow regulator regularly for calcium build up or any blockage that reducing water flow.
/
