American Dynamics 1010T Series Installation And Operating Instructions Manual

Brand: American Dynamics

Model: 1010T Series

Category: Security camera accessories

Type: Installation And Operating Instructions Manual

This manual is also suitable for

1010 Series

1010/T Series

Incandescent Illuminator

This manual describes the installation and operating procedures for the American Dynamics 1010/T Series Illuminator. Before

installation is started, become familiar with all the special features and warnings associated with this equipment. Once

installation is complete, store this manual in a safe, convenient location for future reference.

Installation and Operating Instructions

Table of Contents

Page

Description................................................................. 1

Features...................................................................... 1

General Safety.......................................................... 1

Installation................................................................ 2

Mounting........................................................ 2

Connection..................................................... 2

Twilight Switch.............................................. 2

Lens Selection................................................ 2

IR Illumination Area-vs-Distance.................. 2

Bulb Replacement.................................................... 3

Troubleshooting ....................................................... 4

Dimensions............................................................... 5

Specifications............................................................. Back Page

Information furnished by AMERICAN DYNAMICS is believed to be accurate and reliable. However, no responsibility is

assumed by AMERICAN DYNAMICS for its use; nor for any infringements of other rights of third parties which may result

from its use. No license is granted by implications or otherwise under any patent or patent rights of AMERICAN DYNAMICS.

DESCRIPTION

The 1010T Series Infrared Illuminator provides outstanding

results when used with IR sensitive black/white cameras.

The light produced by the 1010T Series is invisible to the

human eye. This feature is excellent for covert security or

where the addition of visible lighting is not possible.

The 300 watt spot-lamp is designed to project a highly

concentrated IR beam to a distance of 460 feet (140 m),

covering an area 100 ft wide x 66 ft high. Pronounced ribbing

around the two-part black enameled housing dissipates heat to

extend bulb life.

The IR filter is a lamination of vaporized-metal coated glass

and Pyrex subjected to a special hardening process.

A 10 ft (3 m) pendant line cord is standard with the

Illuminator.

FEATURES

☛

120 VAC Input

☛

300 Watt Bulb

☛

Weatherproof Housing

☛

10 ft (3 m) Heavy Duty Pendant Line Cord

GENERAL SAFETY

Observe the following safety instructions without fail:

• The 1010T generates large amounts of heat from the IR

lamp during operation. Determine that no systems

(sprinklers, thermostats, heating vents, etc.) in the

immediate installation area are triggered or damaged as a

result of this thermal radiation (heat).

• Before performing any service on or around the 1010T, shut

down the Illuminator and isolate it electrically to prevent

accidental operation. A cool-off period of approximately

one hour is required after shut down. (Even if the housing

is cool, the IR lamp may still retain enough heat to cause

injury.)

Figure 1 - 1010T Infrared Illuminator

CAUTION

The concentrated high power of the Infrared beam

can cause serious damage to a person's vision!

Maintain a minimum 33 foot (10 m) safety zone

between the Illuminator and any human contact.

INSTALLATION

Mounting

The 1010T IR Illuminator is supplied with a "U-shaped"

bracket for mounting the Illuminator to a wall bracket or a

Pan/Tilt mechanism.

• Ensure the structural soundness of the mounting bracket

support surface.

• Three holes are drilled in the bottom of the mounting

bracket (see Figure 2):

Use the center hole (0.83"/21 mm) to secure the

1010T to a mounting bracket.

Use the two side holes (0.28"/7 mm) to secure the

1010T to a Pan/Tilt unit.

Connection

The 1010T requires a 120 VAC (2.5 Amps) supply voltage.

The 1010T is supplied with a 10 ft (3 m) pendant line cord for

connecting to a power supply (see Table 1).

Table 1 - 1010T Wiring Color Code

Leads Designation

Green Ground

White 120VAC Hot

Black 120VAC Neutral

Twilight Switch

Routing the supply voltage through a twilight switch (not

supplied) extends the operational life of the 1010T. American

Dynamic's recommends using one twilight switch (AD part

number 1010/TS) to operate a maximum of three Illuminator

units.

Lens Selection for 1010/T

Table 2 lists the minimum focal length lens size required to

focus at the maximum spotlight beam range for a particular

camera format.

Table 2 - Minimum Focal Length Lens Size

Maximum Range Camera Format

460 (feet) 1" 2/3" 1/2" 1/3"

Lens Size 75 mm 52 mm 37.5 mm 26 mm

IR Illuminated Area -vs- Distance

The beam transmitted by the 1010/T provides effective IR

illumination to 460 feet (140 meters). Table 3 lists the

spotlight area covered by the beam.

Table 3 - Distance -vs- Area Table

Distance* Area Covered

[Horiz x Vert]

50 ft (15.2 m) 11 x7 ft (3.3 x 2.1 m)

75 ft (22.3 m) 16 x 10 ft (4.9 x 3.1 m)

100 ft (30.5 m) 21 x 14 ft (6.4 x 4.3 m)

125 ft (38.1 m) 26 x 17 ft (7.9 x 5.2 m)

150 ft (45.7 m) 32 x 21 ft (9.8 x 6.4 m)

175 ft (53.3 m) 37 x 24 ft (11.3 x 7.3 m)

200 ft (61 m) 42 x 28 ft (12.8 x 8.5 m)

225 ft (68.6 m) 47 x 31 ft (14.3 x 9.5 m)

250 ft (76.2 m) 53 x 35 ft (16.2 x 10.7 m)

275 ft (83.8 m) 58 x 38 ft (17.7 x 11.6 m)

300 ft (91.4 m) 63 x 42 ft (19.2 x 12.8 m)

325 ft (99.1 m) 68 x 45 ft (20.7 x 13.7 m)

350 ft (106 m) 74 x 49 ft (22.6 x 14.9 m)

375 ft (114 m) 79 x 52 ft (24.1 x 15.9 m)

400 ft (122 m) 84 x 56 ft (25.6 x 17.1 m)

425 ft (130 m) 89 x 59 ft (27.2 x 18.0 m)

450 ft (137 m) 95 x 63 ft (29.0 x 19.2 m)

475 ft (145 m) 100 x 66 ft (30.5 x 20.1 m)

500 ft (152 m) 105 x 70 ft (32.0 x 21.4 m)

*Distances from light source to subject

0.28"/7 mm

0.83"/21 mm

4.25"/108 mm

2.75"/70 mm

0.56"/14.3 mm

Figure 2 - Mounting Bracket Drill Holes

BULB REPLACEMENT

Before servicing the Illuminator, power down the unit and

allow approximately one hour to cool. Replacement bulbs can

be ordered through American Dynamics (part #

AD1010/TBB). IR bulb replacement is done without

removing the Illuminator from its mount.

• Remove the three 4 mm Hex screws holding the main

housing to the rear housing (see Figure 3).

• Pull the defective IR bulb forward and gently remove the

power cord connector from the IR bulb prongs.

• Remove and save the O-Ring (red colored gasket) around

the defective bulb.

• Discard the defective bulb.

• Fit the O-ring (red colored gasket) around the new IR bulb

and plug in the power cord connector taking care not to

crack the porcelain base of the connector.

• Check that the IR bulb O-Ring is properly seated between

the new bulb and the rear housing. Refer to Figure 3.

• Check that the weather seal (black colored gasket) is

properly seated in the rear housing outer rim.

• Insert the IR lamp into the main housing.

• Close the housing and secure the three 4 mm Hex screws.

Main Housing

Rear Housing

4mm

Hex

Screw

Replacement Bulb

Power Cord

w/Connector

O-Ring

Weather Seal

Figure 3 - Bulb Replacement

IF YOU ENCOUNTER ANY PROBLEMS

OPERATING THIS UNIT, OR NEED TECHNICAL

ASSISTANCE, CALL OUR TECHNICAL SUPPORT

CENTER AT:

within the United States: 1-800-442-2225

outside the United States: (914) 624-7640

PROBLEM POSSIBLE CAUSE SOLUTION

Lamp does not come on No 120 VAC to Lamp....................................✔ Check 120 VAC power

....................................✔ Check twilight switch operation (if used)

Bulb burned out .........................................✔ Check bulb connection socket

.........................................✔ Replace bulb

Bulb burns out frequently Lamp operating during daylight hours..................✔ Install twilight switch

Moisture getting into housing............................✔ Check weatherseal

............................✔ Tighten the 3 housing screws

Poor image quality on Camera not sensing IR wavelengths.....................✔ Check that camera is sensitive to IR light

video monitor

Camera does not resolve distant objects.................✔ Poor connections causing low AC voltage

.................✔ Bulb is near end of service life, replace bulb

TROUBLESHOOTING

CAUTION

Do not attempt to service an operational Illuminator!

The heat generated by the IR lamp is sufficient to cause SEVERE

BURNS. Before performing any service on or around the 1010T, shut

down the Illuminator and isolate it electrically to prevent accidental

starting. A cool-off period of approximately one hour is required after

shut down. (Even if the housing is cool, the IR lamp may still retain

enough heat to cause injury.)

CAUTION

Do not look directly into an operational Illuminator!

Since IR light is invisible to the human eye, the only method of verifying

a malfunctioning IR lamp is at the video output location. Before starting

any maintenance work on the 1010T, be certain that the video system (i.e.

cameras, monitors, etc.) is functioning properly.

DIMENSIONS

9.45"

240 mm

8.27"/210 mm 7.48"/190 mm

7.5"

190 mm

Figure 4- 1010/T Dimensions

SPECIFICATIONS

Power: 300 Watt

Operating Voltage: 120 VAC

Current Consumption: 2.5 A

Infrared Wavelength: 850 nm

Beam Dispersion: 12° H x 8° V

Normal Light Range*: 460 ft/140 m

Weatherproof Standard: NEMA-4 (IP65)

Service Life (MTBF): >2000 Hours (Bulb)

Weight: 5.5 pound / 2.5 Kg

Dimensions: (9.45 H x 8.27 W x 7.48 D) inches

(240 H x 210 W x 190 D) mm

ACCESSORIES

AD1010/TBB: 300 watt, PAR 56, bulb

AD1010/TS: Dusk-to-dawn switch (will operate 3 units)

AD1050/PL: "L" Bracket - one IR Illuminator on Patriot Series Pan/Tilt

AD1050/PT: "T" Bracket - two IR Illuminators on Patriot Series Pan/Tilt

AD1050/HL: "L" Bracket - one IR Illuminator on Hercules Series Pan/Tilt

AD1050/HP: "T" Bracket - two IR Illuminators on Hercules Series Pan/Tilt

* Normal range is based on the use of a CCD camera with maximum IR-sensitivity, medium scene reflectance.

An American Dynamics Product

Designed and built by

Sensormatic CCTV Systems Division

One Blue Hill Plaza

Pearl River, New York, 10965

Business: (914) 624-7600

Technical Support Center: 1-800-442-2225

FAX: (914) 624-7685

OP1010T C Made in U.S.A.

April 1994

American Dynamics 1010T Series Installation And Operating Instructions Manual

Brand: American Dynamics

Model: 1010T Series

Category: Security camera accessories

Type: Installation And Operating Instructions Manual

This manual is also suitable for

1010 Series

Download PDF

report

American Dynamics 1010T Series Installation And Operating Instructions Manual

This manual is also suitable for

American Dynamics 1010T Series Installation And Operating Instructions Manual

Related papers

Other documents