Socomec ATyS g Quick Start

Type
Quick Start

This manual is also suitable for

Socomec ATyS g is a reliable automatic transfer switch that ensures a seamless and secure power supply to critical loads. It's designed for applications where uninterrupted power is essential, such as hospitals, data centers, and industrial facilities. With its advanced features, ATyS g guarantees a fast and reliable transfer between two power sources, minimizing downtime and protecting your equipment from power outages.

Socomec ATyS g is a reliable automatic transfer switch that ensures a seamless and secure power supply to critical loads. It's designed for applications where uninterrupted power is essential, such as hospitals, data centers, and industrial facilities. With its advanced features, ATyS g guarantees a fast and reliable transfer between two power sources, minimizing downtime and protecting your equipment from power outages.

ATyS r Removing the motorisation module from the Power Section
1
2
4
5
6
3
125 -> 630 A
800 ->3200 A
ATyS d, t, g and p Removing the motorisation & ATS Controllerfrom the Power Section
125 -> 630 A
800 ->3200 A
REMOVAL / DÉMONTAGE / REMOCIÓN
APPLICABLE TO ALL ATYS R, D, T, G AND P MODELS
ATyS Power Section Replacement
www.socomec.com
http://www.socomec.com/
en/changeover
543304B
QUICK START GUIDE
EN FR ES
HAZARDOUS VOLTAGE. This equipment must be installed and serviced only by qualied electrical personnel.Turn off all power supplying this equipment before working on or inside equipment.
Always use a properly rated voltage sensing device to conrm power is off. Replace all devices, doors, and covers before turning on power tothis equipment. Maintain electrical clearances between cable and live
parts. Failure to follow these instructions will result in death or serious injury.
TENSION DANGEREUSE. L’installation et l’entretien de cet appareil ne doivent être effectués que par du personnel qualié.Coupez l’alimentation de cet appareil avant d’y travailler.Utilisez toujours un dispositif de
détection de tension à valeur nominale approprié pour conrmer que toute alimentation est coupée. Replacez tous les dispositifs, les portes et les couvercles avant de mettre cet appareil sous tension. Maintenez
les distances d’isolement électrique entre le câble et les pièces sous tension. Si ces précautions ne sont pas respectées, cela entraînera la mort ou des blessures graves.
TENSION PELIGROSA. Solamente el personal de mantenimiento eléctrico especializado deberá instalar y prestar servicios de mantenimiento a este equipo.Desenergice el equipo antes de realizar cualquier
trabajo en él.Siempre utilice un dispositivo detector de tensión adecuado para conrmar la desenergización del equipo. Vuelva a colocar todos los dispositivos,las puertas y las cubiertas antes de energizar este
equipo. Mantenga un espacio adecuado para la instalación eléctrica entre el cable y las piezas energizadas. El incumplimiento de estas precauciones podrá causar la muerte o lesiones serias.
DANGER / PELIGRO
1 2 3a
3b 4 5
1 2 3a
3b 4 5
ATyS r Assembling the motorisation module on the Power Section
Pos. = Pos.
125 -> 630 A = 3Nm
800 ->3200 A = 8Nm
5
3
1
2
4
ATyS d, t, g and p Assembling the motorisation & ATS Controller on the Power Section
Pos. = Pos.
125 -> 630 A = 3Nm
800 ->3200 A = 8Nm
ASSEMBLING / MONTAGE / MONTAJE
CORPORATE HQ CONTACT: SOCOMEC SAS, 1-4 RUE DE WESTHOUSE, 67235 BENFELD, FRANCE. Non contractual document.
1 2 3
4a 4b 5
1 2 3
4a 4b 5
  • Page 1 1
  • Page 2 2

Socomec ATyS g Quick Start

Type
Quick Start
This manual is also suitable for

Socomec ATyS g is a reliable automatic transfer switch that ensures a seamless and secure power supply to critical loads. It's designed for applications where uninterrupted power is essential, such as hospitals, data centers, and industrial facilities. With its advanced features, ATyS g guarantees a fast and reliable transfer between two power sources, minimizing downtime and protecting your equipment from power outages.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages