4I4O-ID
installation instructions
Description
The 4I4O-ID is a four input four supervised ouput device that
allows you to connect up to four non-addressable devices to the
PinPoint system. The system provides flexible and reliable two-
way communication between the device and the controller.
Installation
1. Pull the wiring through the wire access opening in the unit
base (Figure 1).
CAUTION You must be free of static electricity before
handling sensor circuit boards. Touch a
grounded, bare metal surface before
touching circuit boards or wear a ground-
ing strap.
2. Mount the base using the appropriate mounting holes.
3. Mount the metal bracket to the base.
4. Mount the circuit board to the metal bracket.
5. Connect the wires to the appropriate screw terminals on
the circuit board and tighten the screws (Figure 3).
6. Set the PinPoint address DIP switches (Figure 2). Devices
are shipped with DIP switches set to 255. This is an
invalid address. The device will no communicate with the
controller until a valid address has been set. Refer to the
controller’s manual to determine the correct address setting
for each unit.
Note The 4I4O-ID requires power to the DC IN
terminals to operate and it will not enroll
without power applied.
7. Attach the unit lid to the base (Figure 1).
8. Test the unit when the PinPoint system is completely
installed and the controller is powered.
Figure 1. Exploded view
Figure 2. Circuit board
Figure 3. Wiring diagram
Terminal
blocks
Tamper switch
ON APEM
SON APEMS
1 2 3 4 5 6 7 8
DIP switches
Lid
Circuit board
Bracket
Base
Wire access opening
+
+
-
-
AC
BATT
l1
COM
l2
COM
l3
COM
l4
COM
01+
01-
02+
02-
03+
03-
04+
04-
-
+
Monitor
Inputs
Outputs
PinPoint bus in
PinPoint bus out to next device
An open will cause AC fault to
be transmitted to contoller. An
open will cause battery fault to
be transmitted to controller. A
short is normal state.
Dual EOL configuration
47K EOL
47K
EOL
47K
EOL
Tamper contact
Single EOL configuration
Power supply
Outputs connect the supply
voltage (12 or 24 VDC)
across the load when on.
Power supply required for
operation.
g
2
4I4O-ID
Installation Instructions
GE Security
12345 SW Leveton Drive
Tualatin, OR 97062
503-692-4052
USA & Canada: 800-547-2556
Tech Support: 800-648-7424
www.ge-security.com
1036048C / September 2004
FCC compliance
This device complies with Part 15 of the FCC rules. Operation is subject
to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interferences tha may cause undesired operation.
Specifications
Housing material Flame retardant ABS
Operating voltage 12/24 VDC
Signaling voltage 4 to 9 V
Current draw 2.2A maximum
Recommended power supply NX-320E (12V), Altronix AL300LX, or
equivalent
Output current 500mA maximum each at 12 or 24 VDC
Signaling current 20mA
Operating temperature 32 to 131°F (0 to 55°C)
Relative humidity 10 to 90% non-condensing
Maximum line length 10,000 feet (3 km)
Dimensions:
Width 6.8 in. (17.3 cm)
Depth 2.0 in. (5.1 cm)
Height 4.8 in. (12.2 cm)
Color White
Listings UL 365, UL 609, UL 985, UL 1023, UL
1610, FCC, CE
Inputs:
Input loop resistance Reported to panel
(47K EOL included)
> 1Meg Ohm Open
47K ± 5% Single EOL
94K ± 5% Double EOL
< 20 Ohm Short
Product ordering
Product Description
4I4O-ID Addressable 4 input and 4
supervised output interface that
allows you to connect up to 4
non-addressable devices to the
PinPoint bus.
/
