Protec Algo-Tec 6600 Commissioning Manual

Protec Fire Detection plc, Protec House, Churchill Way, Nelson, Lancashire, BB9 6RT, ENGLAND

+44 (0) 1282 717171 www.protec.co.uk [email protected].uk

Algo-Tec™ 6500/6600

INTERACTIVE DIGITAL

ADDRESSABLE FIRE CONTROL

SYSTEM (1-4 LOOPS)

COMMISSIONING MANUAL

Document Revision Details

Issue

Modification Detail

Author

Date

2.8

Updated DLP Card addresses

Updated loop Initialisation Fault

Updated device type fault

Added Device Zone Trans Fault

PD

12/12/2018

2.9

Added description of the Promoted master

Updated the description of the MIMIC Device

Missing fault

Added description of Deluge Drive Limit Fault

Updated the description of the Unknown

Active Device Fault

Added damper control module faults

PD

02/05/2019

2.10

Added description of the Loop Disablement

CRC Fault.

Added description of the Loop DLP Queue

fault.

Updated licence fault descriptions.

Added description of the WODU Interface

Board Missing fault.

Updated the description of the Unknown

Active Device Fault.

Renamed Circuit Fault as Supply Out Fault

and updated the description.

Renamed Set Point Position fault as Position

Fault and updated the description.

PD

01/07/2019

3

Minor changes

PD

19/07/2019

Notice

This manual may be revised as a result of enhancements to the system software or hardware. Check

for revisions to this manual, and download them, from the website www.protec.co.uk

Table of Contents

DOCUMENT REVISION DETAILS ................................................................................................................2

INTRODUCTION .........................................................................................................................................5

IMPORTANT INFORMATION FOR 19” RACK SYSTEMS ..................... ERROR! BOOKMARK NOT DEFINED.

1.0 COMMISSIONING MENUS ...............................................................................................................6

1.1 Login ...................................................................................................................................................... 6

1.2 Entering the Menu System ................................................................................................................. 7

1.3 Tools Menu ........................................................................................................................................... 8

1.4 Loop Tools ............................................................................................................................................. 9

1.5 Loop logging ....................................................................................................................................... 10

1.6 Allocate Addresses ............................................................................................................................. 11

1.7 Printer Menu ....................................................................................................................................... 13

1.8 Print current events ........................................................................................................................... 14

1.9 Print Historic Events .......................................................................................................................... 15

1.10 Diagnostic Tools ............................................................................................................................. 16

1.11 Networking ..................................................................................................................................... 17

1.12 Mapping Info .................................................................................................................................. 18

1.13 Quality .............................................................................................................................................. 22

1.14 Loop Info ......................................................................................................................................... 23

1.15 Clear All Disablements .................................................................................................................. 25

1.16 Rebuild ............................................................................................................................................. 25

1.17 Test menu ........................................................................................................................................ 26

1.18 Test options..................................................................................................................................... 27

1.19 Service Info...................................................................................................................................... 28

1.20 Upgrade ........................................................................................................................................... 29

2.0 FAULT EVENTS ................................................................................................................................ 30

2.1 Panel faults (Non-latching) ............................................................................................................... 30

2.2 Panel faults (Latching) ....................................................................................................................... 32

2.3 Network Faults ................................................................................................................................... 35

2.4 Loop faults .......................................................................................................................................... 37

2.5 Loop Device faults .............................................................................................................................. 39

2.6 6000 Digital Device Fault Information ............................................................................................ 41

2.7 IO faults ............................................................................................................................................... 46

2.8 Alarm events ....................................................................................................................................... 47

2.9 DLP Card Identification ..................................................................................................................... 47

3.0 CARD HARDWARE INDICATIONS .................................................................................................. 48

3.1 System Controller Card ..................................................................................................................... 48

3.2 Network Card ..................................................................................................................................... 49

3.3 I/O Card ............................................................................................................................................... 50

3.4 Loop Card ............................................................................................................................................ 51

3.5 Display Card ........................................................................................................................................ 52

4.0 TOUCH SCREEN CALIBRATION ..................................................................................................... 53

5.0 6500 TECHNICAL SPECIFICATION ................................................................................................. 54

6.0 6600 TECHNICAL SPECIFICATION ................................................................................................. 55

7.0 STANDARDS, DIRECTIVES AND REGULATIONS INFORMATION ................................................. 56

Introduction

This manual applies to the Protec 6500 and 6600 fire alarm control panels however for convenience;

reference will be made only to the ‘6500’. Everything in this manual applies to the 6500 and 6600

unless stated otherwise.

The Protec 6500 Fire Alarm Control Panel has been designed and manufactured in the United

Kingdom and complies fully with current standards dictating fire alarm system design practice ( EN54

parts 2 and 4 ).

This equipment and its associated connections must be installed, commissioned and

maintained by a suitably trained skilled and competent person.

This equipment is not guaranteed unless installed and commissioned in accordance with

current national standards

There are no user serviceable parts inside the 6500. The equipment and its associated

connections must be installed, commissioned and maintained by a suitably trained,

skilled and competent person. A separate 6500 Installation Manual is available.

It is assumed that the commissioning engineer has read the 6500 User Manual and is

therefore familiar with the basic operation of a 6500 fire panel.

For information on programming the panel and communicating via the PC using the

commissioning software, refer to the Commissioning Software User Manual

1.0 Commissioning Menus

1.1 Login

Access to the features of the 6500 is achieved by logging in. If it is displayed, Press

Login and the display will show the code entry screen

If the Login button is not displayed, touch the middle of the screen to bring up the code

entry key pad

Enter the engineer code by touching the relevant number buttons then touch Enter. If the code is

correct then the display will show the main menu screen

For information on the Service Info screen and the Upgrade screen

refer to the relevant sections.

1.2 Entering the Menu System

When the engineer code is entered, the ‘Main Menu’ screen will be displayed.

Touch a menu option to select it.

Tools Menu - refer to section 1.3

Test Menu - refer to section 1.17

System View - refer to the user manual

Disable / Enable - refer to the user manual

History - refer to the user manual

Settings - refer to the user manual

1.3 Tools Menu

Touching Tools Menu displays options to show the commissioning tools

The printer menu is displayed if the configuration file downloaded to the panel

included the printer fitted option.

1.4 Loop Tools

Touching Loop tools displays the different loop options.

1.5 Loop logging

Each loop must be logged and allocated. Logging finds all the connected devices, their type, software

version and their physical order whilst Allocating allows the engineer to assign an address to each

device. Until a device is allocated an address on the loop, the panel cannot communicate with it.

To log a loop, touch Loop logging to select the panel, then loop card, and then select the

loop.

Loop logging is a two stage process, first it logs how many devices are connected to

the loop then it maps them to find their physical position on the loop. Knowing their

physical position makes fault finding easier. Loop logging can take several minutes; its

progress is indicated on the display.

Touch Allocate to move direct to the allocation menu (see next section) else touch OK

to exit the logging screen.

1.6 Allocate Addresses

A loop must be logged before it can be allocated

Each Protec ‘6000’ loop device has a unique serial number. This serial number has to be linked to a

unique address. The process of linking the serial number to an address is known as address allocation.

To begin allocating the device addresses, touch Allocate addresses to select the panel,

then loop card, and then select the loop.

Indicates the column used for sorting the data. Touch one of the other column headers to

change the method of sorting.

This button provides a quick way to allocate the selected device to the lowest unused

address, in this case the address is ‘1’.

This button finds the next device in the list to the one selected that has not yet been

allocated an address.

This button finds the previous device in the list prior to the one selected that has not yet

been allocated an address.

This button allocates the selected device the address that has been entered. The address

range is ‘0’ to ‘200’. Each device must have a unique address between ‘1’ and ‘200’. ‘0’ or a

blank address is used to de-allocate a device.

This button deletes the latest digit that has been entered.

On completion of the address allocation, touch Exit.

Touch Exit to leave the allocation menu without saving any changes.

Touch Continue to return to the allocation screen.

Touch Save to store the newly allocated data. A progress bar is displayed as shown

below.

1.7 Printer Menu

Touching Printer Menu displays the printer options.

Note: - The printer menu option is only available on panels configured to have a printer.

Prints Loop Device serial numbers and analogue values after selecting the panel,

the loop card then the loop.

Powers up the printer for a period of time to allow feeding of a new roll of paper.

1.8 Print current events

Touching Print Current Events displays the printer options.

Prints the current faults.

Prints the current disablements.

Prints the current tests.

Prints the current alarms.

1.9 Print Historic Events

Touching Print Historic Events displays the printer options.

Prints the last 100 Fire events from the historic log.

Prints the last 100 Non- Fire events from the historic log.

Prints the last 100 Alarm events from the historic log.

1.10 Diagnostic Tools

Touching Diagnostic tools displays options to show the available tools.

The Networking button is not available on a single panel system.

1.11 Networking

Touching Networking displays options to show the network diagnostic tools.

1.12 Mapping Info

To access all the network information, this must be performed on the master panel.

Slave panels are limited to displaying the network map.

Touch Mapping info then select the Network card. This displays a map of the panels

connected to the network and a summary of the number of panels mapped and

missing.

Pink indicates the master panel with no faults

Green indicates a slave panel with no faults

Yellow indicates that the panel has a fault. A red border to the yellow circle indicates that the

panel is one side of a network break.

Blue indicates a slave panel that is acting as the master.

Touch a panel icon to display its details as shown below.

A panel can have one of three roles:

 Master – The master manages all network functions

 Slave DM – The deputy master assumes control when the master is offline e.g. whilst being

programmed

 Slave – A standard remote network panel

 Promoted Master – A slave panel that is acting as the master panel

The master panel may display additional fault information to that shown above:-

Fault map error

The panel sequence found does not match the sequence downloaded to the master panel.

Fault network failed

There are too many network problems for the network to function.

Fault duplicate master

When the system was programmed, two panels have been set up as the master panel. Download the

corrected configuration to both panels.

Fault too many nodes

The master panel discovered too many nodes when it initialised the network.

The cabling information reports cable break information such as:-

 Break, a panel is reporting a cable break

When using a fibre optics unit cabling information reports cable break information such as:-

 Break-CH1, a panel is reporting a cable break on network Channel 1

 Break-CH2, a panel is reporting a cable break on network Channel 2

The status information reports issues such as:-

 Missing, a panel that should be on the network is currently missing

 Duplicate, two panels have the same panel number

 Unknown, an unknown panel is on the network

 Reverse, a panel has its channel 1 & 2 wiring reversed

Page is loading ...

Protec Algo-Tec 6600, Algo-Tec 6500 Commissioning Manual

Related papers

Other documents