Pi Tape METRIC for Linear Rule Operating instructions

Brand
Pi Tape
Model
METRIC for Linear Rule
Type
Operating instructions

Pi Tape METRIC for Linear Rule is a versatile measuring device designed to provide precise linear measurements. Its key capabilities include:

  • Accurate Measurements: Equipped with a vernier scale that divides each millimeter into 10 parts, the Pi Tape METRIC enables precise measurements down to 0.1 millimeters.

  • Easy Reading: The clear and easy-to-read scale allows for quick and accurate readings, minimizing errors in measurement.

  • Convenient Design: The compact and portable design of the Pi Tape METRIC makes it easy to handle and carry, allowing for convenient use in various settings.

Pi Tape METRIC for Linear Rule is a versatile measuring device designed to provide precise linear measurements. Its key capabilities include:

  • Accurate Measurements: Equipped with a vernier scale that divides each millimeter into 10 parts, the Pi Tape METRIC enables precise measurements down to 0.1 millimeters.

  • Easy Reading: The clear and easy-to-read scale allows for quick and accurate readings, minimizing errors in measurement.

  • Convenient Design: The compact and portable design of the Pi Tape METRIC makes it easy to handle and carry, allowing for convenient use in various settings.

TO READ METRIC LINEAR RULE WITH A VERNIER SCALE
© Copyright 2019 Pi Tape Texas LLC. All rights reserved. https://pitape.com
PI TAPE and the logo are trademarks of Pi Tape Texas, LLC, and they are registered in the USA and in 45 other countries.
Please visit https://www.pitape.com/trademarks.htm for a list of countries in which our trademarks are registered.
Vernier Scale divides each graduation on Gage Member
into 10 parts or .1mm
EXAMPLE
LINEAR RULE
VERNIER SCALE
Make certain the linear rule, vernier section and object to be measured are clean.
Each line on the linear rule represents 1mm, while each line on the vernier represents .1mm.
Place the linear rule on a flat surface. Slide the linear rule alongside the part to be measured.
Line up the zero end of the linear rule (left end) with the end of the part to be measured. Make certain the left
end of the rule and the left end of the part to be measured line up exactly.
Line up the vernier scale portion of the linear rule at the point where the part being measured ends. This will
place the zero on the vernier scale exactly at the right end of the part to be measured.
Locate the Zero-edge of Vernier scale and note the highest value achieved on linear rule above it
(the highest value to the left of Vernier scale). In this example, the value is 1073mm.
Next, determine which vernier line is aligned exactly with a marked division line on the linear rule.
In this example, the value is 3 (.3mm).
Finally, to obtain the linear reading of the object, simply add the two values together:
1073mm + .3mm = 1073.3mm
As a suggestion for checking very large measurements – pieces of masking tape can be used to hold the rule
and vernier section in the proper parallel position.
Tape resolution 0.1mm
Care
Tape is delicate, handle with care. Keep tape clean and dry.
After each use, wipe clean and apply a light rust preventive oil*. Store in tape container and in a low moisture environment.
* White Easy to Read tapes Stainless or 1095 Spring Steel - Do not oil or use solvents to clean this product.
White Easy to Read 1095 Spring Steel must be stored in a low moisture environment to prevent rust.
No periodic adjustments are needed.
Make sure the tape has not been stepped on or kinked, which may destroy the tape tolerance.
September 2022 Rev C
  • Page 1 1

Pi Tape METRIC for Linear Rule Operating instructions

Brand
Pi Tape
Model
METRIC for Linear Rule
Type
Operating instructions

Pi Tape METRIC for Linear Rule is a versatile measuring device designed to provide precise linear measurements. Its key capabilities include:

  • Accurate Measurements: Equipped with a vernier scale that divides each millimeter into 10 parts, the Pi Tape METRIC enables precise measurements down to 0.1 millimeters.

  • Easy Reading: The clear and easy-to-read scale allows for quick and accurate readings, minimizing errors in measurement.

  • Convenient Design: The compact and portable design of the Pi Tape METRIC makes it easy to handle and carry, allowing for convenient use in various settings.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents