© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
Plan View
10’
10’
VK-1326 - 10’ x 10’ Hybrid Inline
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS
© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
= 1 sq foot
Plan View
© 2023
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information
© 2023
Order #XXXXX
TSP46 Profile
All knobs must be tightened securely to ensure a proper connection.
Adjust connectors if necessary to
prevent gaps in connection.
Upper Horizontal Extrusion
Lower Horizontal Extrusion
Corner
Connector Corner
Connector
Corner
Connector
Corner
Connector
COMPLETED ASSEMBLY
Slide verticals over
lower connectors.
Then slide upper
connectors into
groove of verticals.
Tighten all knobs.
Corner Connection
3) Tighten all knobs to secure connection.
Disassembly
1) Loosen knobs on vertical extrusions.
2) Slide the vertical extrusions off of
corner connectors on lower and upper
horizontal extrusions.
1) Loosen knobs, then slide vertical extrusions onto
corner connectors of lower horizontal extrusion.
2) Slide corner connectors of upper horizontal
extrusion into grooves of vertical extrusions.
Disassembly
1) Loosen all knobs.
2) Slide connectors off of one extrusion.
3) Tighten knobs to prevent loss during
packing & shipping.
Keep straight connectors in groove of
extrusion. Do not remove connectors
during disassembly.
Straight Connection
3) Tighten all knobs to secure connection.
When assembling frame, first attach all straight
connectors, then attach corner connectors.
1) Place extrusions end-to-end.
Slide connector across seam of extrusions.
Tighten all knobs.
All knobs must be tightened securely to ensure a proper connection.
Straight Connector
2) Loosen all knobs, then slide straight
connector across the seam of extrusions.
TSP46 Frame Assembly
© 2023
Order #XXXXX
Straight Connection
Adjust connectors if necessary to
prevent gaps in connection.
Upper Horizontal Extrusion
Lower Horizontal Extrusion
COMPLETED ASSEMBLY
3) Tighten all knobs to secure connection.
Slide verticals over
lower connectors.
Then slide upper
connectors into
groove of verticals.
Tighten all knobs.
When assembling frame, first attach all straight
connectors, then attach corner connectors.
1) Place extrusions end-to-end.
CEI152 Profile
Slide both connectors across seam of extrusions.
Tighten all knobs.
All knobs must be tightened securely to ensure a proper connection.
All knobs must be tightened securely to ensure a proper connection.
Corner
Connectors Corner
Connectors
Corner
Connectors Corner
Connectors
Straight Connector
Straight Connector
2) Loosen all knobs, then slide straight
connectors across the seam of extrusions.
Disassembly
1) Loosen all knobs.
2) Slide connectors off of one extrusion.
3) Tighten knobs to prevent loss during
packing & shipping.
Corner Connection
3) Tighten all knobs to secure connection.
Disassembly
1) Loosen knobs on vertical extrusions.
2) Slide the vertical extrusions off of
corner connectors on lower and upper
horizontal extrusions.
1) Loosen knobs, then slide vertical extrusions onto
corner connectors of lower horizontal extrusion.
2) Slide corner connectors of upper horizontal
extrusion into grooves of vertical extrusions.
Keep straight connectors in groove of
extrusion. Do not remove connectors
during disassembly.
CEI152 Frame Assembly
© 2023
Order #XXXXX
Using Your Setup Instructions
Cleaning and Packing Your Display
The Euro LT Hybrids Setup Instructions are created specifically for your configuration.
They are laid out sequentially in levels, including exploded views, and a logical series of detailed steps
to assemble the main structure and components. We encourage you to study the instructions before
attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your exhibit to prevent loss of the
locks and setscrews (see below in RED). This is VERY IMPORTANT.
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.
2) When cleaning laminate inserts, countertops, or panels use mild cleansers and a soft material
such as cotton.
3) Keep all display components away from extreme heat and long exposure to sunlight to avoid
warping and fading.
4) Retain all packing material. It will make re-packing much easier and will reduce the likelihood
of shipping damage.
Each component has 2 clips,
the lower clip is ALWAYS
black. The top clip is color
coded to distinguish which
level. The color coded clip
also contains the numbered
label.
Connector
Level 1 = Blue
Level 2 = Red
Level 3 = Green
Level 4 = Black
Panel Lock
When Required
Color Coded Clip
w/ assembly number
Black Clip
is bottom of
panel
L
e
f
t
P
a
n
e
l
R
i
g
h
t
P
a
n
e
l
Cut Away View of
Slide Clips
Components connect together
by aligning them and sliding
downward connecting clips
together.
Configurations are assembled
from left to right, usually
starting with #1 and following
the numbered sequence.
Example of Connection Top View of Panels with Locks
The first level of components contain
panel locks that are located at the top of
the panel for extra stability and seamless
connection. When disassembling panels
twist top connection slightly and lift right
panel upward.
Panel Lock
When Required
Color Coded Clip
w/ assembly number
is top of panel
Left Hand
Grasps Panel
Firmly
With Right Hand Thumb
Close to Seam
Squeeze,
Push Forward,
And Lift
General Setup Instructions for Extrusion System
The Tool Typical Connection Typical Connection (cont’d) Numbered Label
Most exhibits can be assembled
with the supplied Hex Key Tool.
Occasionally, a flat head screw-
driver may be required.
Most horizontal extrusion connections have a patented expandable
lock. This lock inserts into the groove of an opposing extrusion.
Tightening the lock with the Hex Key Tool expands the lock and
creates a strong positive connection.
Each extrusion contains a numbered
label which corresponds with setup
instructions. The label is located
within a groove of the extrusion
(when possible). With extrusion
components the labels contain
Black numbers unless otherwise
specified.
Detail A Detail B Detail C
Horizontal Inline Connection (remove only one setscrew) Base Plate Connection Vertical Connection
(remove only two setscrews)
Detail D Detail E
Setscrews
Remove only (1) setscrew when disassembling.
Replace setscrew in extrusion after assembling
it. Before packing, replace setscrew in extrusion
to avoid losing it.
Attach base plate to round or
square vertical extrusion using
the bolt provided. Be careful
not to strip the threads.
When vertical extrusions are
packed in portable cases rather
than crates or tubs, they must be
broken down into smaller sections
which then require assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews
in extrusion after assembling it.
Before packing, replace setscrews
in extrusion to avoid losing them.
EuroLT Assembly
© 2023
Order #XXXXX
Graphic Removal
To remove the graphic
the frame, locate the fabric
pull tab. Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
from
SEG Installation
© 2023
Crate 1 of 1
Order #XXXXX
Locked layer contains
placeholder marks.
CRATE PACKING
Crate Packing
© 2023
Step 1 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
Note: Closet
Door opens in
4C
2A
5
1A
9
6
6A
10
Door
Infill
Infill
9
9
9
11
7
8
*
**
*Door Threshold
*
*
*
*
Door Threshold
Tighten
setscrew
to secure
Slide Connector
into Groove
of Extrusion
Door Threshold
Attachment
*
V4 Connector
Slide V4 connector into groove of
vertical extrusion; tighten set screw
on V4 to secure in place.
Connect frame extrusion extrusion
to V4 connector using bolt.
*
V4
Connector
set
screw
bolt
S44
Frame
Door Stopper to Vertical Attachment
PR37
Extrusion
Profile
Slide PR37 extrusion into
groove of vertical and tighten
set screw to secure in place.
Item
1A
2A
4C
5
6
6A
7
8
9
10
11
Qty.
1
1
1
1
1
1
1
1
4
1
1
Description
95”h S44 Vertical Extrusion
95”h S44 Vertical Extrusion
95”h TSP46 Vertical Extrusion
95”h TSP46 Vertical Extrusion
48”w TSP46 Horizontal Extrusion
48”w TSP46 Horizontal Extrusion
95”h S44 Vertical Extrusion w/ Door Stop
95”h S44 Vertical Extrusion
24”w Z45 Horizontal Extrusion
44.417”w Z140 Horizontal Extrusion
24”w Door Threshold
Steps:
Refer to the TSP46 Frame Assembly general information page.
1) Assemble verticals [4C,5] between horizontals [6,6A] using corner connectors.
2) Attach horizontal [10] between verticals [4C,5].
3) Connect verticals [4A,5] to verticals [1A,2A] using bolts & V4 Connectors.
See V4 Connector detail.
4) Attach Door Threshold [11] between verticals [2A,7].
See Door Threshold Attachment detail.
5) Connect horizontals [9] between verticals [1A,8], [2A,7], inserting Infills.
6) Install Door between verticals [2A,7]. See Door Attachment detail.
7) Apply SEG graphic to front frame assembly. Refer to the SEG Installation
general information page.
Door
Hinge
Hinge
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
Door Attachment
*
Pin
S
E
G
Graphi
c
Note: Door swings inward
Backwall Assembly
© 2023
Step 2 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
1A
wing
wing
Connect transformer to puck lights, then
attach transformer to power source.
Puck Light Connection
*
Transformer
To
Power
Puck Light
Ceiling
Screw
V4
Connector
Slide V4 connector into groove
of horizontal extrusion; tighten
set screw to secure V4 in place.
Insert screw through hole of ceiling
into threaded hole of V4 connector;
tighten screw to secure.
Canopy Attachment
*
Monitor Mount
S
E
G
Gra
p
h
i
c
Note: Monitor mount installs over SEG graphic.
Screw
Caps
Monitor Mount Attachment
*
Install Monitor Mount to
Stand-off Barrels using screw caps.
Attach Stand-off Barrels to horizontal
extrusion using wing nuts.
Stand-Off
Barrels
Wing
nuts
Z
14
0
Item
A
Qty.
1
Description
60”w x 23”d x 2.5”h Ceiling Panel
Steps:
1) Attach Ceiling Panel [A] to top of closet assembly, using bolts. See Canopy Attachment detail.
2) Connect power to Puck Lights in ceiling. See Puck Light Connection detail.
3) Install Monitor Mount to horizontal [10]. See Monitor Mount Attachment detail.
4) Attach Wings to vertical [1A] using A10 clamps. See Wing Attachment detail.
1) Slide A10 connector
into groove of extrusion.
2) Tighten set screw to
secure A10 to extrusion.
3) Insert Wing into Clamp.
4) Tighten knob to secure
wing in place.
Wing Attachment
*
Wing
1
2
3
4
Monitor
Mount
*
*
*
*
*
*
*
**
**
A
Backwall Assembly (cont’d)
© 2023
Step 3 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
*
PR63 Attachment
1) Run cords through
PR63 plastic conduit.
2) Attach conduit where
indicated by pinching
the opening and
inserting into the
groove of extrusion.
pinch
PR63 conduit
CEI152 PR63
Top View
*
Lock Clip into Groove of
Horizontal Extrusion, then
slide Light onto Clip.
Light Attachment
Slide light into light
receiving hardware
Lock into
groove of
horizontal
Item
1/1A
2/2B
--
--
Qty.
1/1
1/1
1
1
Description
48”w CEI152 Horizontal Extrusion
95”h CEI152 Vertical Extrusion
Base Plate w/ foot
95”h V31 Connector
Steps:
Refer to the CEI152 Frame Assembly general information page.
1) Assemble verticals [2,2B] between horizontals [1,1A] using corner connectors.
2) Attach Base Plate to side of frame assembly. See Base Plate Attachment detail.
3) Attach vertical [2B] to closet vertical [7] using V31 connector. See V31 Connection detail.
4) Connect light to top of SEG frames. See Light Attachment detail.
5) Attach PR63 Conduit where shown for wire managment.
See PR63 Attachment detail.
6) Apply SEG graphics to frame assembly. Refer to the
SEG Installation general information page.
1
1A
Base
Plate
2B
7
2
*
V31 Connection
Slide V31 connector
into channels of
vertical extrusions.
Tighten
set screws
to secure.
*Top View
CEI152
S44
V31
bolt
wing
nut
bolt
bolt
key hole
Corner Base Plate Attachment
*Place key hole over bolt
on vertical extrusion and
slide down; secure with
bolts & wing nuts.
*
Light
15” PR63
85” PR63
S
E
G
Graphi
c
Backwall Assembly (cont’d)
© 2023
Step 4 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
When assembled
Item
1
2
3
4
5
6
7
8
1,1A
Qty.
1
1
1
1
1
1
1
1
1,1
Description
23”w x 38”h LT Panel
38”h LT 90° Corner Connector
14.125”w x 38”h LT Panel
38”h LT 90° Corner Connector
23”w x 38”h LT Panel w/ Door
38”h LT 90° Corner Connector
14.125”w x 38”h LT Panel
38”h LT 90° Corner Connector
35” S44 Vertical Extrusion
Monitor Mount Attachment
Connectors
V4
Connectors
*
Slide V4 Connectors into groove
of Extrusion. Tighten Set Screws
to secure connectors in place.
Attach Monitor Mount back
piece to Extrusion, using bolts.
Then slide monitor mount into
back piece.
Bolts
Monitor
Mount
Back
Piece
Steps:
Refer to the LT Panel Assembly general information page.
1) Assemble panels & connectors [1] through [10] in numerical order as shown.
2) Connect verticals [1-1A] together. See S44 Connection detail.
3) Attach vertical assembly [1/1A] to panel [5] using screw caps.
4) Affix Shelf Supports to inside of counter assembly; place Shelf onto supports.
5) Slide Counter Top over verical assembly [1/1A] & secure to top of counter
assembly. See Counter Top Attachment detail.
6) Install Monitor Mount to vertical [1/1A]. See Monitor Mount Attachment detail.
Screws
Connector
S44 Connection
Slide extrusion over
connector and rest on
lower vertical;
secure with screws.
**To prevent product loss,
Keep all screws attached
to connector piece after
disassembling
*
12
Counter Top Attachment
*
Align hole with pin. Rotate pin. Spring
will push pin into hole.
FRONT VIEW
1
2
3
45
6
7
8
5
1
1A
*
screw
cap
screw
cap
Monitor
Mount
Shelf Supports
Shelf Supports
Counter Top
Shelf
*
*
*
MOD-1527 Kiosk Assembly
/
