Classic Exhibits VK-1341 Setup Instructions

Type
Setup Instructions
© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
Top View
10’
10’
VK-1341 - 10’ x 10’ Hybrid Inline
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS
© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
= 1 sq foot
Plan View
© 2023
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information
© 2023
Crate 1 of 1
Order #XXXXX
Locked layer contains
placeholder marks.
CRATE PACKING
Crate Packing
© 2023
Step 1 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
When assembled
All Velcro faces
back of booth
FRONT VIEW
Assemble frame flat on ground.
6
11
11
88A 10
7
2A
2
3A
3
5A
5
4A
4
99A 11
Steps:
1) Connect vertical extrusions [2-2A], [3-3A], [4-4A], [5-5A] together.
See S44 Connection detail.
2) Attach base plates [1] to vertical extrusions, using bolts.
3) Attach horizontals [8] to [8A] and [9] to [9A].
See Z45 Connection detail.
4) Connect horizontals [6,7,8/8A,9/9A,10,11] between
ertical assemblies as shown.
5) Affix graphics to back of backwall assembly, using Velcro.
Item
1
2,2A
3,3A
4.4A
5,5A
6
7
8,8A
9,9A
10
11
Qty.
4
1,1
1,1
1,1
1,1
1
1
1,1
1,1
1
1
Description
Base Plate
42” S44 Vertical Extrusion w/ PR37
42” S44 Vertical Extrusion w/ PR37
42” S44 Vertical Extrusion w/ PR37
42” S44 Vertical Extrusion w/ PR37
22” Z45 Horizontal Extrusion
22” Z45 Horizontal Extrusion
28.875” Z45 Horizontal Extrusion
28.875” Z45 Horizontal Extrusion
22” Z45 Horizontal Extrusion
22” Z45 Horizontal Extrusion
Z45 Connection
*
PR53
Connector
Z45 Z45
Insert connector into extrusions.
Secure with set screws.
Set Screw
To prevent product loss, keep all
screws attached to connector
after disassembling.
PR53
Connector
S44 Connection
Slide upper extrusion
over connector and
rest on lower extrusion.
Secure with set screws.
*
To prevent product loss,
keep all screws attached
to connector after
disassembling.
Set Screw
*
*
****
Backwall Assembly
© 2023
Step 2 of 4
Order #XXXXX
Using Your Setup Instructions
The Aero Setup Instructions are created specifically for your configuration. The instructions include an
exploded view of the frame which is sequentially labeled. We encourage you to review the instructions
before attempting to assemble your exhibit.
Connections are kept very simple; no tools required. Everything assembles with push-button connectors.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.
2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood
of shipping damage.
Push-Button
Push-Button
66
6
6
Numbered Label
Connections are made by holding the button down and
sliding the red tube into opposing tube until button locks
into the hole of the opposing tube. To disassemble, push button
and pull or twist extrusions apart.
Locked layer contains
placeholder marks.
Steps:
1) Connect canopy pieces together as shown.
2) Slide fabric cover over assembled canopy
then zip closed.
A
A
B
B
D
D
CC
Button
Push button then rotate
for packing.
Slide canopy mount into groove of
extrusion, then turn canopy mount
clockwise to tighten.
Canopy Mount Attachment
Extrusion
Canopy
Mount
Turn to
Tighten
Place Aero frame over
top of canopy mount.
Canopy
Mount
Aero Frame
Canopy Assembly
© 2023
Step 3 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
Shelf
Canopy
Header
Shelf
Shelf
Shelf
*
*
*
*
*
Slide light onto clip then lock clip
into groove of horizontal extrusion.
Clip
Light
Light Attachment
Clip
Light
Horizontal Extrusion
Shelf Attachment
Insert lock into groove of vertical
extrusion, then tighten set screw.
Lock
Set Screw
Back of Shelf
*
Canopy
Mount Canopy
Mount
5A
3A
7
11
9A
9
4A
5
3
4
**
12
Counter Top
Monitor
Mount
Item
12
Qty.
1
Description
38.414” S40 Angled Extrusion Tighten set screw to
secure A10 to extrusion.
A10 Clamp
Tighten knob to secure
wing panels.
*
***
Steps:
1) Attach clamps to [7] [9/9A] and [11]. See A10 Clamp detail.
Clamp header to top of assembed backwall.
2) Attach lights, where desired, to top of assembled backwall.
See Light Attachment detail.
3) Attach canopy mounts to [7] and [11]. See previous page
for Canopy Mount Attachment detail. Place assembled
canopy onto canopy mounts, with zipper facing to back.
4) Attach counter top between extrusions [3] and [12].
5) Attach shelves to [4] and [5]. See Shelf Attachment detail.
6) Attach monitor mount to [3A]. See Monitor Mount Attachment detail.
Completed Assembly
Monitor Mount Attachment
Connectors
V4
Connectors
*
Slide V4 Connectors into groove
of Extrusion. Tighten Set Screws
to secure connectors in place.
Attach Monitor Mount back
piece to Extrusion, using bolts.
Then slide monitor mount into
back piece.
Bolts
Monitor
Mount
Back
Piece *
Backwall Attachments
© 2023
Step 4 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
Door
Completed Pedestal Assembly
Infill
5
7
Keep extrusions [1/4/6/6A] assembled.
4A
3A
5
7
2
3
6
6A
1
4
6
6A Keep extrusions [2/3/6/6A] assembled.
*
Pedestal Top
Shelf
Shelf
Support
Align hole with pin Rotate pin. Spring
will push pin into hole.
Pedestal Top Attachment
12
*
*
Steps
1) Attach horizontal extrusions [5] and [7] between assemblies [1,4,6,6A] and [2,3,6,6A],
making sure Velcro is facing inward.
2) Connect vertical extrusions [3A] and [4A] on top of horizontal extrusion [7].
3) Slide infill between verticals [3A] and [4A].
4) Attach assembled door to vertical extrusion [1]. See Door Connection detail.
5) Attach upper horizontal extrusions [5] and [7] between assemblies and on top of infill and door.
6) Connect shelf supports to Velcro, then set shelf on top of supports.
7) Attach pedestal top to extrusions [6A]. See Pedestal Top Attachment detail.
Door
Hinge
Hinge
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
Door Attachment
*
Pin
*
*
Item
1
2
3
3A
4
4A
5
6,6A
7
Qty.
1
1
1
1
1
1
2
2,2
2
Description
38“ GS220 Vertical Extrusion w/ Door Hinges
38” GS220 Vertical Extrusion w/ Door Stop
38“ GS210 Vertical Extrusion
34.417” Z33 Vertical Extrusion
38” GS210 Vertical Extrusion
34.417” Z33 Vertical Extrusion
22.0197“ Z45 Horizontal Extrusion
12.5” Z45 Horizontal Extrusion
25.639“ Z45 Curved Extrusion
MOD-1267 Pedestal Assembly
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Classic Exhibits VK-1341 Setup Instructions

Type
Setup Instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI