White Wall Mounted 28” Drop-Down Cabinet
and Desk
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-sf02w
SKU: DESK-SF02W
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
2 3
STEP 2
Insert x8 Wood Dowel Pins (K) into edges of Rear Panel (B).
PACKAGE CONTENTS
TOOLS NEEDED
22lbs
(9.98kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
A (x1)
Bottom Panel
B (x1)
Rear Panel
C (x1)
Le Panel
D (x1)
Right Panel
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
Drill
Level
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS.
ADULT SUPERVISION IS REQUIRED.
ASSEMBLY STEPS
STEP 1
Insert x3 Cam Lock Screws (J) into Bottom Panel (A), and x2 Wood Dowel Pins (K) into
sides of Panel.
E (x1)
Top Panel
F (x1)
Front Panel
G (x2)
Strut
H (x1)
Bumper
I (x2)
Corner Brace
J (x18)
Cam Lock Screw
K (x12)
Wood Dowel
Pin
L (x18)
Cam Lock Nut
M (x20)
Screw
N (x2)
Upper Ball Joint
O (x2)
Lower Ball Joint
P (x1)
Magnet
W-A (x2)
Wall Screw
W-B (x2)
Concrete Anchor
W-C (x2)
Washer
A
B
F
C
E
D
Q (x1)
Handle
R (x2)
Plug
S (x2)
Handle Screw
T (x2)
Hinge
U (x12)
Hinge Screw
J
A
K
K
B
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO
MOUNT. We include mounting hardware for brick and concrete walls. If unsure, please contact us at
vivo-us.com, email at [email protected], or call us at 309-278-5303.
4
STEP 7
Attach Handle (Q) to front of Front Panel (F) using Handle Screws (S). Once
tightened, insert Plugs (R) into holes.
STEP 8
STEP 9
Attach Upper Ball Joints (N) to Le and Right Panels (C, D) using x6 Screws (M). Attach Lower
Ball Joints (O) to Front Panel (F) using x4 Screws, making sure each ball is facing in.
With the assembled cabinet standing up, place the Front Panel (F) face-down in front with the
bottom edge flush with the cabinet. Assemble the Hinges (T) to the cutouts in the assembled
cabinet and Front Panel using Hinge Screws (U), making sure the Phillips head on each Hinge is
facing into the cabinet as shown in the diagram.
STEP 3
Assemble Rear Panel (B) to Bottom Panel (A).
STEP 5
Assemble Le and Right Panels (C, D) to previously assembled
Bottom and Rear Panel (A, B), then place Top Panel (E) onto
assembled cabinet.
STEP 4
Insert x4 Cam Lock Screws (J) into Le Panel (C) and x1 Wood Dowel Pin into top of Panel.
Repeat for Right Panel (D). Insert x7 Cam Lock Screws into Top Panel (E), and attach Magnet
(P) to Top Panel using x2 Screws (M).
STEP 6
Insert all Cam Lock Nuts (L) into Bottom, Rear, Le and Right Panels. Turn all Nuts clockwise
using a Phillips screwdriver to lock Panels together.
D
E
C
J
K
M
P
Keep the Door Closer (P)
aligning with the edge of
the Top Pane l (E) whil e
screwing.
L
F
Q
S
R
U
T
1
2
a
b
N
M
1
2
O
M
Keep magnet aligned with
the edge of Top Panel
while tightening screws.
Close the assembled cabinet and check alignment of the
Front Panel. If the Panel is not aligned, turn the Phillips head
screw on each Hinge to align the Panel.
STEP 14
OPTION A: Wood Wall Installation
Place assembled cabinet against wall
and mark drilling locations through
Corner Braces (I2). Use of a level and
stud finder is highly recommended.
If mounting holes do not align with
studs, we recommend mounting a
solid wood panel to the wall so the
cabinet may be fully supported.
Using a 3/16” drill bit, drill holes 2.2”
deep into marked locations. Mount
cabinet to wall using Wall Screws
(W-A) and Washers (W-C). Reattach
Covers (I1) to Corner Braces.
NOTE: Do not use Concrete Anchors
(W-B) with wood walls.
STEP 15
Place laptop and other items on desk
when open and in use. When not in use,
all devices may be stored inside.
STEP 10
Extend the Struts (G) to their full length. Snap large ends onto Upper Ball Joints (N) and extending
ends onto Lower Ball Joints (O).
STEP 11
Press Bumper (H) into holes in Bottom Panel (A).
STEP 13
Attach Corner Braces (I2) to Le and Right Panels (C, D) using x8 Screws (M).
OPTION B: Concrete/Brick Wall
Installation
Place cabinet against wall and mark
drilling locations through Corner
Braces (I2). Use of a level is highly
recommended.
Using a 3/8” drill bit, drill holes 2.4”
deep into marked locations, then insert
Concrete Anchors (W-B) into holes.
Mount cabinet to wall using Wall Screws
(W-A) and Washers (W-C). Reattach
Covers (I1) to Corner Braces.
1
G
2
H
STEP 12
Remove Covers (I1) from Corner
Braces (I2).
I
I1
I2
I2
M
ø 4.5 m
O
N
uu
√
W-A
W-C
I1
u
1
2
ø 10 m
O
N
uu
√
1
W-A
W-C
W-B
I1
2
LAST UPDATED: 03/04/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303
/
