Rev-A-Shelf 432-VF30SC-3 Operating instructions

Brand: Rev-A-Shelf

Model: 432-VF30SC-3

Type: Operating instructions

This manual is also suitable for

432-VF30SC-6

Rev-A-Shelf 432-VF30SC-3 is a soft-close base filler with slides that can be installed in 20 minutes. It includes scribe rails that can be adjusted to fit your specific cabinetry and comes with a shipping strap that should not be removed until after installation. The filler can be mounted to adjacent cabinets using pre-drilled holes, and it comes with screws for both frameless and face-frame applications. The filler also has adjustable tabs that allow you to adjust the height of the front slide by up to 1/8 inch.

I-432SC-1214

Installation Instructions for Soft-Close Base Filler with Slides

Note: Do not remove front shipping strap prior to installation!

Step 1. Measure scribe rail thickness and length per your

specic cabinetry. (See Fig 1a and 1b)

Step 2. Install upper and lower scribe rails to ller pullouts being careful not to split the

wood. If using screws to attach, be sure to pre-drill rst. Align scribe rails with front edge of

ller pullouts. Align scribe rail to upper section of base cabinet lower mounting. (See Fig 2)

Note: If installing pullout in a frameless application, it is recommended to that a 1/16” thick

scribe rail be used to space the ller unit properly.

Step 3. Pre-drill holes using your 3/16” drill bit. See the table below for

measurements specic to your ller height. After pre-drilling has been

completed on one cabinet side, repeat with adjacent cabinet.

Step 4. Mount ller cabinet pullout to adjacent cabinet. Make sure ller is ush

with the top of the cabinet wall and behind the face-frame if applicable.

Fig 1a

Fig 1b

Cabinet Wall

Scribe rail measurements

Front of Cabinet

Scribe Rail

width dimension

Front of Cabinet

Scribe Rail

Length

Top Scribe Rail is nailed

to edge of top section

Bottom scribe rail is nailed

to edge of bottom section

Fig 2

“Changing the way you think about cabinet organization!”

“Cambiamos su percepción sobre la organización de armarios”

“Nous changeons votre conception de l’aménagement des armoires”

www.rev-a-shelf.com

1-800-626-1126

432 Series Filler Pullout Instructions

Instrucciones del armario de relleno deslizante – Serie 432

Directives de montage du module coulissant série 432

I-432-TRI-1012

Fig 1

Step 1. Measure scribe rail thickness and length per your

See Fig 1

Fig 2

Step 2. Install upper and lower scribe rails

or brads. See Fig 2. Note: Align scribe rails

scribe rail to upper section of base cabinet

lower mounting strap or lower section of

wall cabinet lower mounting strap. See

Figs. 3a-b.

Top Scribe Rail is nailed to

bottom edge of top section

Fig 3a

Wall Cabinet

Bottom Scribe Rail is nailed

to edge of bottom section

Top Scribe Rail is

nailed to edge of

top section

Fig 3b

Base Cabinet

Bottom Scribe Rail is

nailed to edge of

bottom section

Fig 4a

Fig 4b

Step 3. (Base Cabinets). Pre-drill 3/16 inch holes 3/8

inch down from top of cabinet and also 27-3/4” down

from top of cabinet. (See Fig 4a-d). Repeat with other

adjacent cabinet.

Fig 5a

Fig 5b

Step 4.

See Fig. 5a-b

Fig 6

Step 5.

to adjacent cabinet 2. See Fig. 6

Fig 8

Fig 9

Step 7. Attach face frame and onlays (not provided) See Fig. 8-9

Fig 7

Step 6. Remove front mounting strap.

See Fig 7.

Filler Cabinet

Base Cabinet

Scribe Rail Meets Face Frame

From inside the adjacent

cabinet screw the 432 to

cabinet top.

Fig 4c Wall Cabinet

Screw 432 to cabinet bottom

from below adjacent cabinet.

Screw 432 to cabinet top

from above adjacent

cabinet.

Fig 4d Base Cabinet

From inside and

above the adjacent

the 432 to cabinet

bottom.

Filler Cabinet

Base Cabinet

Scribe Rail Meets Face Frame

Fig 3

TOOLS REQUIRED:

ESTIMATED ASSEMBLY

TIME:

20 MIN

CARE AND MAINTENANCE:

CLEAN WITH A DAMP CLOTH

AND WIPE PARTS DRY

3/16”

Shipping Strap

Step 5. Mount ller cabinet pullout to remaining adjacent cabinet.

12400 Earl Jones Way • Louisville • KY • 40299 | 800.626.1126 • FAX: 502.491.2215 | www.rev-a-shelf.com

Filler Size (Height)

Measurement #1

From Top of Cabinet, Down

Measurement #2

From Top of Cabinet, Down

26” Filler 3/8” 23-7/8”

30” Filler 3/8” 27-7/8”

Note: Your pullout unit does not need to be removed for installation. If you encounter an issue that requires the unit to be removed, the release levers

for the Blum Tandem slides are located as shown. (See Fig 6a-b).

Step 6. Remove front shipping strap. (See Fig 4)

Step 7. Attach onlays or door panels. (not provided). (See Fig 5)

Fig 4

Shipping Strap

Fig 5

Back of pullout

Fig 6a

Fig 6b