Page is loading ...
© ®
P S I
G P M
Tub and Shower Bathroom Faucet
STANDARDS
Tools:
PLUMBERS PUTTY FLASHLIGHT BASIN WRENCH
SAFETY GLASSES SCREWDRIVER
PLIERSCHANNELLOCKS ADJUSTABLE WRENCH
HEX-KEY TAPE
Helpful Information
Flow Rate Chart
Eleganzia
2017-12-22 MAAN4323-1
SEALED-TUBE
Please keep the tools for future use!
ASME A112.18.1/CSA B125.1
ASME A112.18.2/CSA B125.2
LISTED IAPMO/cUPC
Gather the necessary tools as shown below to complete the installation of
this faucet. Some may not be needed depending on the model of faucet you
are installing. Check with your local hardware store on the requirements of
your installation situation.
WARNING:
Attention:
Important
For easy installation, you will need:
- To read all the installation instructions completely before beginning.
- To read all the warning, attention and maintenance information.
- To purchase the proper supply lines.
Tighten connection with two wrench to prevent
damage to tube body. Be careful not to bend the
stem as this will void the product warranty.
Connect to water supply lines with either
risers with the coupling nuts or
supplied tube head interior connector or
A. B. C.
Faucet Installation
1
2
Tools might be applied to the following places:
Installation size map
Remove the protective cover and
take out the screw with the
screwdriver, then remove the
protective plate .
Connect pipes with faucet as shown, pay attention to the
connection of hot and cold water supply pipe.
3
Let the water run for one minute. Check all connections for leakage.
3
2
1
17 9/16 in.
(446.8 mm)
13 1/4 in.
(336.3 mm)
ø8 11/16 in.
(221.1 mm)
1 in.
(25 mm)
5 9/16 in.
(142 mm)
1/2-14NPT
1 5/8 - 2 3/8 in.
(41 - 60 mm)
4 1/2-14NPT
3 1/16 in.
(78.1 mm)
6 11/16 in.
(170.1 mm)
8 1/4 in.
(210.2 mm)
8 3/4 in.
(223 mm)
2 3/16 in.
(56.2 mm)
6 1/4 in.
(158.7 mm)
Checking and Testing
Maintenance:
4
5
Apply teflon tap to the shower arm , put
flange and connect it to water supply
pipe. After fixing the shower arm, screw
the shower head to the shower arm.
ATTENTION: don't forget the o-ring
between the shower arm and the
shower head. Position trim plate ,
fix it with screws , then tighten with
screwdriver. Put the knob , and fix the
handle with screw, finally put the
index . Then assemble the outlet spout
, loosen the screw and connect the
spout to the water supply pipe, then
tighten the screw again with allen key.
Simply rinse the surface with clear water or
mild liquid detergents (if necessary). Dry the
faucet with a clean soft cotton cloth. Do not
use any cleaning agents containing acids
polish abrasives or harsh cleaners.
Maintenance
Check all connections at arrows for
leaks, retighten if necessary.
BUT DON’T OVERTIGHTEN
1
2
3
Remove the handle screw with
allen key, take out the handle,
then remove the trim cap.
If faucet leaks from the handle or drips from spout, please replace cartridge following the steps:
Unscrew the cartridge nutwith
adjustable wrench, then take out
the old cartridge.
Place a new cartridge in the
cartridge seat, then screw the
cartridge nut and assemble the
handle by securing the screws.
O-ri ng
3
2
1
4
5
7
8
9
6
10
4
3
1
2
1
2
10
1. Clean it with water and dry it with soft cloth.
2. Clean the product with gentle liquid or glass cleaner.
3. Don't use acid cleaner.
4. Don't clean with abrasive material, abrasive paper or knife.
Cleaning and care
Daily cleaning and care are required in order to keep the product shining and working properly.
4
5
6
7
8
9
10
11
24
19
20
21
22
23
1
2
3
25
26
27
14
12
13
15
18
17
16
28
29
Parts list
NO. PART NAME
Flange1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Shower arm
Shower head
Screw
Protect cover
Trim cap
Cartridge locknut
Cartridge
Sleeve
Body
Check valve
Trim plate
Knob
Handle
Screw
Joint
Joint
Joint
Screw
20
21
22
23
24
25
26
27
28
29
O-ring
Screw
Index
Allen key
Spout
Screw
O-ring
Aerator
O-ring
Connector
/