Barco Projector adapter plate Installation guide

Brand: Barco

Model: Projector adapter plate

Type: Installation guide

Interface plate

BACK UP

PROJECTOR

MASTER

PROJECTOR

RLM HDX, CLM, SLM

FLMHDX

Special bolt +

Lock washer

Long bolt

Spacer

Stacking point

Washer

Spacer

Short bolt +

Lock washer

Special bolt +

Lock washer

HDX

SLM

CLM

HDX

SLM

CLM

FLM

RLM

FLM

RLM

FLM

HDX

RLM

SLM

CLM

HDX

RLM

Installation manual

For HD X an d FL M

R9864050

R5905082/00

17/05/2011

Barco nv Events

Noordlaan 5, B-8520 Kuurne

Phone: +32 56.36.82.11

Fax: +32 56.36.88.24

Support: www.barco.com/esupport

Visit us at the web: www.barco.com

Printed in Belgium

Changes

Barco provides this manual ’as is’ w ithout warranty of any kind, either expressed or implied, including but not limited to the implied war-

ranties or m erchantability and ﬁtness for a particular purpose. Barco m ay make improvements and/or cha nges to the product(s) and/or the

program(s) described in this publication at any time without notice.

This pub lication could contain technical inaccuracies or typographical errors. Changes are periodically m ade to the information in this

publication; these changes are incorporated in new editions of this publication.

wise be recorded, transmitted or

stored in a retrieval system without the prior written consent of Barco.

Disposal Information

This equipment has required the ex traction and use of natural resources for its production. It may contain hazardous sub stances for health

and environme nt. In order to av oid the d issem ination of those substances in the environment and to diminish the pressure on natural

resources, we encourage you to use the appropriate take-back systems. Those systems will reuse or recycle most of the materials of your

end of life equipment in a s ound way.

The crossed-out wheeled bin symbol invites you to use those s ystem s. If you need more inform ation on the collection, reuse and recycling

systems, please contact y our local or r egional waste administrator. You can also contact us for m ore information on the env ironmental

performances of our products.

Trademarks

Brand and product names mentioned in this manual may be trademark

s, registered trademarks or copyrights of their respective holders.

All br and and product names mentioned in this manual serve as com men ts or examples and are not to be understood as advertising for

the products or their manufacturers.

Table of contents

TABLE OF CON TENTS

1. Interface plate...................................................................................................... 3

1.1 Introduction .......................................................................................................................... 3

1.2 Safety ................................................................................................................................ 4

1.3 What you need to know before starting.. . . . ........................................................................................ 5

2. Using a HDX as master projector............................................................................... 7

2.1 Using a RLM as back up pro jector — standing conﬁguration ...................................................................... 7

2.2 Using a RLM as back up projector — suspended conﬁguration.................................................................... 9

2.3 Using a CLM as back up pro jector — standing conﬁguration ...................................................................... 9

2.4 Using a CLM as back up projector — suspended conﬁguration.................................................................... 11

2.5 Using a SLM as bac kup projector — standing conﬁguration.......................................................................12

2.6 Using a SLM as bac kup projector — suspended conﬁguration....................................................................13

3. Using a FLM as master projector...............................................................................15

3.1 Using a HDX as backup pro jector — s tanding conﬁguration ......................................................................15

3.2 Using a HDX as backup projector — suspended conﬁguration.................................................................... 16

3.3 Using a RLM as back up pro jector — standing conﬁguration ...................................................................... 17

3.4 Using a RLM as back up projector — suspended conﬁguration.................................................................... 19

3.5 Using a CLM as back up pro jector — standing conﬁguration ...................................................................... 19

3.6 Using a CLM as back up projector — suspended conﬁguration.................................................................... 25

3.7 Using a SLM as bac kup projector — standing conﬁguration.......................................................................26

3.8 Using a SLM as bac kup projector — suspended conﬁguration....................................................................27

R5905082 INTERFACE PLATE 17/05/2011

Table of contents

2 R5905082 INTERFACE PLATE 17/05/2011

1. Interface plate

1. INTERFACE PLATE

Purpose of the Interface plate

The Interface plate is ex clusively designed for the Barco DP2K- xxB series Digital Cinema projectors and can thus not be used on

any other equipment.

Overview

• Introduction

• Safety

• What you need to know before starting

1.1 Introduction

Function

The interface plate m akes it possible to ﬁx two projectors onto each other.

BACK UP

PROJECTOR

MASTER

PROJECTOR

RLM

HDX, CLM, SLM

FLMHDX

Special bolt +

Lock washer

Long bolt

Spacer

Stacking point

Washer

Spacer

Short bolt +

Lock washer

Special bolt +

Lock washer

HDX

SLM

CLM

HDX

SLM

CLM

FLM

RLM

FLM

RLM

FLM

HDX

RLM

SLM

CLM

HDX

RLM

Image 1-1

One projector can be us ed as a m aster projector and the other one as a backup projector. The b ackup projector and m aster projector

can not be of the same type.

Following types of projectors c an be used as a master projector:

• HDX

•FLM

Following types of projectors c an b e used as a backup projector:

•RLM

• HDX (only if the ma ster projector is a FLM projector)

•CLM

•SLM

Order info & content of the kit

When ordering the Interface plate for HDX and F LM, refer to article number R9864050.

The table below gives a n ov erview of the content of the kit.

Article n um ber Description Quantity Image

R5905082 This installation manual 1 image 1-2

R871541 Interface plate 1 image 1-3

G115800 S hort bolt (M10x20) 3 image 1-4

A556248 Long bolt ( M10x 50) 4 image 1-5

R819157 Stacking point 4 image 1-6

R5905082 INTERFACE PLATE 17/05/2011 3

1. Interface plate

Article n um ber Description

Quan tity

Image

R858106

Spacer

7 image 1-7

R871542

Special bolt

8 image 1-8

V367513 Lock washer 8 image 1-9

Z3675541 Washer 3 image 1-10

Image 1-2 Image 1-3 Image 1-4

Image 1-5 Image 1-6 Image 1-7

Image 1-8 Image 1-9 Image 1-10

1.2 Safety

Safety instructions

Read and heed the following warnings and cautions.

R5905082 INTERFACE PLATE 17/05/2011

1. Interface plate

WARNING: The procedures below may only be performed by Barco trained and qualiﬁed technicians.

WARNING: Do not use the interface plate anymore if the blind rivet nuts becam e loose. Using the interface

plate with loose blind rivet n uts can cause a suspended pro jector to f all dow n an d cause serious injury or

dea th.

1.3 What you need to know before starting

WARNING: Do not use the interface plate anymore if the blind rivet nuts becam e loose. Using the interface

plate with loose blind rivet n uts can cause a suspended pro jector to f all dow n an d cause serious injury or

dea th.

How does the special bolt work?

A spec ial customized bolt (reference 1, image 1-11) with a partly reduced diameter is used. Drive the bolt in the blind rivet nut

(reference 2, image 1-11) until it comes loose again.

Image 1-11

How to lock a stacking point?

Lock a stacking point by rotating the ring a quarter turn clockwise w hile pushing it downwa rds u ntil the ring it clicks in (image 1-12).

A B

C D

Image 1-12

R5905082 INTERFACE PLATE 17/05/2011 5

1. Interface plate

6 R5905082 INTERFACE PLATE 17/05/2011

2. Using a HDX as master projector

2. USING A HD X AS MASTER PR OJECTOR

2.1 Using a RLM as backup projector — standing conﬁguration

Necessary tools

17 m m open-end wrench

How to setup?

1. Prepare the interface plate:

a) Install the 4 lock washers and 4 special bolts (reference 1, image 2-1) on the interface plate in the holes m arked with “HDX”.

Drive in the spe cial bolts until they come loose again according to the principle explained above.

Image 2-1

b) Place 4 spacers (reference 2, image 2 -2) on the holes marked with “RLM”. Insert 4 special bolts with lock washer from the

underside of the plate. H and-tighten the 4 special bolts and release them back for 1 turn.

Image 2-2

2. Position the interface plate on top of the HD X projector. Make sure the 4 special bolts (reference 3, image 2-3) on the interface

plate match the b uilt-

in nuts (reference 4, image 2-3) on the HDX projector. Tighten the 4 special bolts.

R5905082 INTERFACE PLATE 17/05/2011

2. Using a HDX as master projector

Image 2-3

3. Place the m ultifunctional frame (reference 5 , image 2-4) on t

op of the HDX projector w ith interface plate. Drive the s pacers

(reference 2, image 2-4) in the multifunctional frame by turning them anticlockwise with a 17mm open-end wre nch. Tighten the

4 special bolts (reference 6, image 2-4) to secure the spacers.

Image 2-4

4. Install the RLM projector in the multifunctional frame (image 2-5). F or d etailed information, consult the installation m anual of the

multifunctional frame.

R5905082 INTERFACE PLATE 17/05/2011

2. Using a HDX as master projector

Image 2-5

2.2 Using a RLM as backup projector — suspended conﬁguration

Necessary tools

17 m m open-end wrench

How to setup?

1. Install the HDX projector on the bo ttom carry handle (image 2-6). Fo r detailed information, consult the installation manual of the

HDX projector.

Image 2-6

2. Perform the same steps as d escribe

d in "Using a RLM as backup pro jector — standing conﬁguration", page 7 .

3. Turn the stack upside down and suspend the HDX bottom carry h andle from a truss. Both projectors will be suspended upside

down.

CAUTION: The multifunctional f rame from the RLM projector is not designed to carry a HDX projector. Do not

suspend the conﬁguration from the multifunction frame. Doing so can cause serious injury or death.

2.3 Using a CLM as backup projector — standing conﬁguration

Necessary tools

• 17 m m open-end wrench

• 8 mm Allen wrench

R5905082 INTERFACE PLATE 17/05/2011

2. Using a HDX as master projector

How to setup?

1. Prepare the interface plate:

a) Install the 4 lock washers and 4 special bolts (reference 1, image 2-7) on the interface plate in the holes m arked with “HDX”.

Drive in the spe cial bolts until they come loose again according to the principle explained above.

Image 2-7

b) Place 3 stacking points (reference 2, image 2-8) on the ho les marked with “ CLM”. Insert 3 long bolts an d tighten.

Image 2-8

2. Position the interface plate on top of the HD X projector. Make sure the 4 special bolts (reference 3, image 2-9) on the interface

plate match the b uilt-in nuts (reference 4, image 2-9) on the HDX projector. Tighten the 4 special bolts.

Image 2-9

10 R5905082 INTERFACE PLATE 17/05/2011

2. Using a HDX as master projector

3. Place the CLM projector with carry handle (reference 5, image 2-10) on top of the HDX projector w ith interface plate. M ake su re

the stacking points match together (reference 6, image 2-10).

Image 2-10

4. Lock the stacking points.

2.4 Using a CLM as backup projector — suspended conﬁgurat

ion

Necessary tools

• 17 m m open-end wrench

• 8 mm Allen wrench

How to setup?

1. Install the HDX projector on the bottom carry handle (image 2-11). For detailed information, consult the installation m anual of the

HDX projector.

Image 2-11

2. Perform the same steps as d escribed in "Using a CLM as backup projector — standing conﬁgur ation", page 9 .

3. Turn the stack upside down and suspend the HDX bottom carry h andle from a truss. Both projectors will be suspended upside

down.

R5905082 INTERFACE PLATE 17/05/2011

2. Using a HDX as master projector

2.5 Using a SLM as backup projector — standing conﬁguration

Necessary tools

• 17 m m open-end wrench

• 8 mm Allen wrench

How to setup?

1. Prepare the interface plate:

a) Install the 4 lock washers and 4 special bolts (reference 1 , image 2-12) on the interface plate in the holes marked with “HDX”.

Drive in the spe cial bolts until they come loose again according to the principle explained above.

Image 2-12

b) Place 3 stacking points (reference 2, im age 2-13) on the holes marked with “SLM”. Insert 3 long bolts and tighten.

Image 2-13

2. Position the interface plate on top of the HDX projector. M ake su re the 4 special bolts (reference 3, image 2-14) on the interface

plate match the built-in nuts (reference 4, image 2-14) on the HDX pro jector. Tighten the 4 special bolts.

R5905082 INTERFACE PLATE 17/05/2011

2. Using a HDX as master projector

Image 2-14

3. Place the SLM projector with carry handle (reference 5, image 2-15) on top of the HDX projector with interface plate. Make sure

the stacking points m atch together (reference 6, imag e 2-15

Image 2-15

4. Lock the stacking points.

2.6 Using a SLM as backup projector — suspended conﬁguration

Necessary tools

• 17 m m open-end wrench

• 8 mm Allen wrench

How to setup?

1. Install the HDX projector on the bottom carry handle ( image 2-16). F or detailed information, consult the installation manua l of

the HDX projector.

R5905082 INTERFACE PLATE 17/05/2011

2. Using a HDX as master projector

Image 2-16

2. Perform the same steps as d escribed in "Using a SLM as backup projector — standing conﬁguration", page 12 .

3. Turn the stack upside down and suspend the HDX bottom carry h andle from a truss. Both projectors will be suspended upside

down.

R5905082 INTERFACE PLATE 17/05/2011

3. Using a FLM as master projector

3. USING A FLM AS M ASTER PROJECTOR

3.1 Using a HDX as backup projector — standing conﬁguration

Necessary tools

• 17 m m open-end wrench

• 8 mm Allen wrench

How to setup?

1. Prepare the interface plate:

a) Place 3 spacers with washer (reference 2, image 3-1) on the interface plate on the holes marked with “FLM”. Hand-tighten

the 3 bolts with lock washers (reference 1, image 3-1) and release them back for 1 turn.

Image 3-1

b) Place 4 stacking points (reference 3, imag

e 3-2) on the ho les marked with “HDX”. Insert 4 long bolts and tighten.

Image 3-2

2. Position the interface plate on top of the FLM projector. Make sure the 3 spacers (reference 4, image 3-3) on the interface plate

match the built-in nuts (reference 5, im age 3-3) on the FLM projector. Tigh ten the 3 spacers.

Secure the interface plate on the FLM projector by tightening the 3 bolts with lock washer.

R5905082 INTERFACE PLATE 17/05/2011

3. Using a FLM as master projector

Image 3-3

3. Place the HD X projector with carry handle (reference 6, image 3-4) on top of the FLM projector w ith interface plate. M ake sure

the stacking points match together (reference 7, image 3-4).

Image 3-4

4. Lock the stacking points.

3.2 Using a HDX as backup projector — suspended conﬁguration

Necessary tools

• 17 m m open-end wrench

• 8 mm Allen wrench

How to setup?

1. Perform the same steps as d escribed in "Using a HDX as backup pro jector — standing conﬁguration", page 15.

2. Turn the stack upside down and suspend the FLM projector from a truss. Both projectors will be suspended upside down.

R5905082 INTERFACE PLATE 17/05/2011

Page is loading ...

Barco Projector adapter plate Installation guide

Barco Projector adapter plate Installation guide

Barco Projector adapter plate Installation guide

Related papers

Other documents