Andrew ValuLine Installation guide

Brand: Andrew

Model: ValuLine

Type: Installation guide

to antenna

hand tighten nuts

INSTALLATION

DURING MOUNT

PROTECTIVE CAP

DO NOT REMOVE

evenly and torque

nuts (4) to

22Nm (16.2lb-ft)

to a vertical pipe of diameter 48-115mm

(1.9-4.5").

The mount also provides adjustment in the

ranges of ±25° fine elevation and

±180° (±10° fine) azimuth.

experienced personnel Andrew installation

practices.

unsafe installation

responsibility for the results of improper or

Andrew disclaims any liability or

maintenance and condition of equipment.

personnel to verify proper installation,

inspected once a year by qualified

personnel. antenna systems should be

instructions have been written for such

Notice

The installation, maintenance, or removal of

antenna systems requires qualified,

Description

This antenna consists of a 0.2-metre(20cm)/

0.3-metre (1ft)/ 0.6-metre (2ft) reflector,

radome, feed and offset tower mount.

The mount is designed to attach the antenna

When fitting

Apply loctite (8)

to threads

before fitting

Visit our Web site at www.andrew.com or contact your local Andrew Wireless Solutions representative for more information.

102222

Bulletin

Version Rev EREStatus

102222

BRE01

Bulletin

RevStatusModel Version

Version RevStatus

0.2m(20cm), 0.3m(1ft) & 0.6m(2ft)

ValuLine Antenna Mount

1 of 2page

Installation Instructions

A CommScope Company

GRE

Andrew Institute offers installation training.

Andrew Wireless Solutions

Andrew Wireless Solutions is a trademark of CommScope. All trademarks identified by

® or ™ are registered trademarks or trade-

marks, respectively, of CommScope. This document is for planning purposes only and is not intended to modify or supplement any

Other Europe: +44 592 782 612

U.K.: 0800 250055

or 1-888-235-5732

U.S.A., Canada, Mexico: 1-800-255-1479

Customer Service 24 hours

specifications or warranties relating to Andrew Wireless Solutions products or services.

www.andrew.com

Notice: Andrew disclaims any liability or responsibility for the results of improper or unsafe installation, inspection, maintenance, or removal practices.

Aviso: Andrews no acepta ninguna obligacion ni responsabilidad como resultado de practicas incorrectas o peligrosas de instalacion, inspecci6n, mantenimiento o retire.

Avis : Andrew decline toute responsabilite pour les consequences de procedures d'installation, d'inspection, d'entretien ou de retrait incorrectes ou dangereuses.

Hinweis: Andrew lehnt jede Haftung Oder Verantwortung fur Schaden ab, die aufgrund unsachgemaBer Installation, Uberprufung, Wartung Oder Demontage auftreten.

Atencao: A Andrew abdica do direito de toda responsabilidade pelos resultados de praticas inadequadas e sem seguranca de instalacao, inspecao, manutengao ou remocao.

Awertenza: Andrew declina eventual! responsabilita denvanti dell'esecuzione di procedure di installazione, ispezione, manutenzione e smontaggio improprie o poco sicure.

0.3m (1ft) Application

(Single Pole version shown)

mount Kit (item 2)

* Part of Pre-assembled

(item 7- Protective Caps)

Rotate to adjust Azimuth

DO NOT REMOVE

Azimuth (top & bottom)

Slacken bolts 1/2 turn to adjust

elevation

Rotate to adjust

to adjust Elevation

slacken bolts 1/2 turn

Table 1 Antenna Parts list

Item Description Qty

1 1ft or 2ft Reflector Assembly 1

2 Pre-Assembled Mount Kit

3 M10x35 c'sk skt hd screw, SS

4 M10 Nut

5 M10 Lockwasher

6 M10 Flatwasher 4*

7 Protective Cap 4*

8 Loctite, tube 1/2ml 1*

9 Allen key fo M10 c'sk screws 1*

10 Conductive grease, tube

Table 2. Fastener Torque Specifications

Torque Values in Nm (lb.ft) for

each fastener

Fastener

Size

M5 M6 M8 M10 M12 16

Stainless

Steel

4.5

(3.3)

7.7

(5.7)

18.7

(13.8)

39.2

(28.9)

65.1

(48)

161

(118.7)

Galvanised

Steel

2.7

(2)

4.5

(3.3)

11.1

(8.1)

(16.2)

(28)

(70.1)

Antenna

offset Left

0.2m(20cm), 0.3m(1ft) & 0.6m(6ft)

102222

BRE01

Bulletin

RevStatusModel Version

Version RevStatus

2 of 2page

Installation Instructions

A CommScope Company

GRE

Andrew Institute offers installation training.

Andrew Wireless Solutions

Awertenza: Andrew declina eventual! responsabilita denvanti dell'esecuzione di procedure di installazione, ispezione, manutenzione e smontaggio improprie o poco sicure.

Visit our Web site at www.andrew.com or contact your local Andrew Wireless Solutions representative for more information.

Andrew Wireless Solutions is a trademark of CommScope. All trademarks identified by

Other Europe: +44 592 782 612

U.K.: 0800 250055

or 1-888-235-5732

U.S.A., Canada, Mexico: 1-800-255-1479

Customer Service 24 hours

® or ™ are registered trademarks or trade-

marks, respectively, of CommScope. This document is for planning purposes only and is not intended to modify or supplement any

specifications or warranties relating to Andrew Wireless Solutions products or services.

www.andrew.com

Notice: Andrew disclaims any liability or responsibility for the results of improper or unsafe installation, inspection, maintenance, or removal practices.

Aviso: Andrews no acepta ninguna obligacion ni responsabilidad como resultado de practicas incorrectas o peligrosas de instalacion, inspecci6n, mantenimiento o retire.

Avis : Andrew decline toute responsabilite pour les consequences de procedures d'installation, d'inspection, d'entretien ou de retrait incorrectes ou dangereuses.

Hinweis: Andrew lehnt jede Haftung Oder Verantwortung fur Schaden ab, die aufgrund unsachgemaBer Installation, Uberprufung, Wartung Oder Demontage auftreten.

Atencao: A Andrew abdica do direito de toda responsabilidade pelos resultados de praticas inadequadas e sem seguranca de instalacao, inspecao, manutengao ou remocao.

ValuLine Antenna Mount