KarliK ICUSB-7 User manual

Brand: KarliK

Model: ICUSB-7

Type: User manual

KarliK ICUSB-7 is a double USB charger designed to power up your smartphones, tablets, and other electronic devices quickly and efficiently. With a nominal input voltage of 100-240V and a maximum output power of 20W, it provides a powerful charge for your devices. It supports various charging protocols, including Apple, Samsung AFC, Huawei FCP, SCP, QC 2.0, and QC 3.0, ensuring compatibility with a wide range of devices.

USER MANUAL - ICUSB-7

DOUBLE USB CHARGER

Specification of ICUSB-7 double USB charger

The ICUSB-7 charger is intended to charge devices like smartphones, tablets and other electronic

equipment. Before connecting the device, check compliance of the charger with charging

parameters of the given device.

1 I 3

Specification

Number of USB ports (type C)

Nominal input voltage

100-240 V~ 50/60Hz

Nominal output current

ź5V/3A, 9V/2.22A, 12V/1.67A (when device is

connected to only one USB output)

ź5V/3.1A (in the case of connecting devices to

two outputs, the output current is divided

equally between each USB socket)

Maximum output power

20 W

Maximum power consumption in idle mode

0.1 W

Operating temperature and humidity

-10 ÷ +40 C; 20~90% RH

Storage temperature and humidity

-20 ÷ +85 C; 10~95% RH

Ingress protection degree

IP 20

53,90

45,50

2 I 3

Detection function of available charger protocols:

- when using only one USB-C output

APPLE

5V 2.4A

BC 1.2

DCP 5V 1.5A

SAMSUNG AFC

HUAWEI FCP

5V, 9V, 12V

SCP

QC 2.0

5V, 9V, 12V

QC 3.0

11.70V max

- when using both 2 x USB-C outputs

APPLE

BC 1.2

DCP 5V 1.5A

SAMSUNG AFC

HUAWEI FCP

SCP

QC 2.0

5V, 9V, 12V

QC 3.0

Warranty is granted for a period of 12 months of the date of purchase. The defective MCUSB-7 charger

along with the proof of purchase should be sent to the manufacturer or to the seller. Warranty does not

include mechanical damages, defects resulting from unauthorised repairs and improper use of the

product.

Warranty period will be extended for the duration of the repair.

Warranty conditions

ASSEMBLY INSTRUCTIONS

3 I 3

NOTE!

The connection to the installation should be done as shown in Figure 2. With improper connection, the

charger may be damaged or may work incorrectly.

The installation must be done by a person with sufficient qualifications, with power supply

disconnected, and must comply with national safety standards.

5. Set the assembly block in the box (9) with tabs or screws at the box (8).

3. Dismantle the USB charger modules (4).

4. Remove the spacer frame (5) from the assembly block (7). Pull away the block tabs or pull the frame

tightly to do this.

7. Insert the intermediate with the USB charger module (4) into the intermediate frame (5) and screw it

onto the mounting block (7) with the screw (2).

6. Connect the power cable to the terminal block of the USB charger module (see figure 2),

respectively the phase wire under the "L" terminal, the neutral wire under the "N" terminal.

8. Attach the label and glass pane.

1. Remove the glass panel (1) with the label applying a knife or a flat screwdriver in the recess (3).

2. Unscrew the screw (2) and pull out the adapter (3) together with the USB charger module (4). If

necessary, you can detach the USB charger module (4) from the adapter (3) by simultaneously

pressing the two movable clips on the USB charger module (4).

Fig. 1

Fig. 2

321

KarliK ICUSB-7 User manual

KarliK ICUSB-7 User manual

KarliK ICUSB-7 User manual

Related papers

Other documents