VISUAL COMFORT S 2189 User manual

Type
User manual

VISUAL COMFORT S 2189 is a versatile wall lantern suitable for both indoor and outdoor use, particularly in wet locations. It features a sturdy construction with a mounting plate for secure installation and a lantern that can be easily attached and detached. The fixture includes all necessary hardware for hassle-free assembly and installation. With its classic design, the VISUAL COMFORT S 2189 adds a touch of elegance to any space while providing reliable illumination.

VISUAL COMFORT S 2189 is a versatile wall lantern suitable for both indoor and outdoor use, particularly in wet locations. It features a sturdy construction with a mounting plate for secure installation and a lantern that can be easily attached and detached. The fixture includes all necessary hardware for hassle-free assembly and installation. With its classic design, the VISUAL COMFORT S 2189 adds a touch of elegance to any space while providing reliable illumination.

1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove mounting plate (B) from fixture body (G) by removing side
screws (F).
3. Remove lantern (I) from fixture body (G) by removing side screws (H).
4. Using mounting plate (B) as a guide, line up with the junction box
and mark anchor positions.
5. Using a drill bit slightly smaller than the anchor, drill holes in the
marked positions. Install anchors (A) into holes using the hammer.
6. Install mounting plate (B) to junction box and secure with mounting
screws (D), then secure wood screws (C) to anchors (A).
7. Wrap fixture ground wire (green) around the green grounding
screw (see diagram 1). Tighten. Continue fixture ground wire and
connect to supply ground wire (usually green or bare copper) using
wire nut (E).
NOTE: It is imperative that the fixture is grounded.
8. Connect fixture neutral wire (white) to the supply neutral wire
(usually white) using wire nut (E).
9. Connect fixture hot wire (black) to the supply hot wire (usually
black) using wire nut (E).
CAUTION: Do not reverse the hot and neutral connections.
10. Make sure all wire connections are tight, then carefully tuck into the
junction box.
Halle Petite Wall Lantern
Item # S 2189
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
NOTICE:
Phillips Screwdriver Slotted Screwdriver Drill
Hammer Pencil
Diagram 1
A
G F
I
H
B
EC
D
Bulb not included
Diagram 2
Drain hole
Halle Petite Wall Lantern
Item # S 2189
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
11. Install fixture body (G) to mounting plate (B) and secure with side
screws (F).
12. Install light bulb into the socket.
13. Install lantern (I) to fixture body (G) and secure with side screws (H).
NOTE: For wet location installation drain hole must be positioned at
bottom of fixture frame. See diagram 2.
FOR OUTDOOR/WET LOCATION INSTALLATION:
14. Using silicon compound, apply a small bead where backplate meets
the wall to prevent water from entering.
NOTE: Large gaps will need to be corrected before applying
silicon compound.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do
not use abrasive or chemical agents.
NOTICE:
Diagram 1
A
GF
I
H
B
EC
D
Bulb not included
Diagram 2
Drain hole
  • Page 1 1
  • Page 2 2

VISUAL COMFORT S 2189 User manual

Type
User manual

VISUAL COMFORT S 2189 is a versatile wall lantern suitable for both indoor and outdoor use, particularly in wet locations. It features a sturdy construction with a mounting plate for secure installation and a lantern that can be easily attached and detached. The fixture includes all necessary hardware for hassle-free assembly and installation. With its classic design, the VISUAL COMFORT S 2189 adds a touch of elegance to any space while providing reliable illumination.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI