VISUAL COMFORT CHO2935AI-CG User manual

Type
User manual

VISUAL COMFORT CHO2935AI-CG is a Fresno Medium 2-Light 3/4 Wall Lantern designed for outdoor or wet locations. It requires two light bulbs (not included) and features a sturdy construction with a mounting plate, support cable, and ground wire for secure installation. The lantern's elegant design includes glass panels, metal bars, and screws for easy assembly. With its stylish appearance and weather-resistant properties, this lantern is an excellent choice for illuminating your outdoor spaces.

VISUAL COMFORT CHO2935AI-CG is a Fresno Medium 2-Light 3/4 Wall Lantern designed for outdoor or wet locations. It requires two light bulbs (not included) and features a sturdy construction with a mounting plate, support cable, and ground wire for secure installation. The lantern's elegant design includes glass panels, metal bars, and screws for easy assembly. With its stylish appearance and weather-resistant properties, this lantern is an excellent choice for illuminating your outdoor spaces.

Fresno Medium 2-Light 3/4 Wall Lantern
Item # CHO 2935
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
NOTICE:
TOOLS REQUIRED (NOT INCLUDED):
1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove mounting plate (B) from fixture (G) by removing screws (F).
3. Using mounting plate (B) as a guide, line up with the junction box and
mark anchor positions.
4. Using a drill bit slightly smaller than the anchor, drill holes in the
marked positions. Install anchors (A) into the holes using hammer.
5. Install mounting plate (B) to the junction box and secure with
mounting screws (D), then secure wood screws (C) to anchors (A).
6. Run support cable through hole on back of mounting plate (B).
Loosen cable lock and install to end of support cable. Insert cable
through the other side of cable lock and tighten ends with a screwdriver
to secure. (See diagram 1)
7. Wrap fixture ground wire (bare copper) around the green grounding
screw (see diagram 2). Tighten. Continue fixture ground wire and
connect to supply ground wire (usually green or bare copper) using
wire nut (E).
NOTE: It is imperative that the fixture is grounded.
8. Connect fixture neutral wire (white) to the supply neutral wire (usually
white) using wire nut (E).
9. Connect fixture hot wire (black) to the supply hot wire (usually
black) using wire nut (E).
CAUTION: Do not reverse the hot and neutral connections.
US
M
L
I
D
S
E
T
Phillips Screwdriver Slotted Screwdriver Drill
Hammer Pencil
Diagram 1
Diagram 2
Diagram 3
E F G
J
H
KL
I
DCB
Bulbs not included
A
Fresno Medium 2-Light 3/4 Wall Lantern
Item # CHO 2935
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
NOTICE:
10. Make sure all wire connections are tight, then carefully tuck into the
junction box.
11. Install fixture (G) to mounting plate (B) and secure with screws (F).
12. Install light bulbs into the sockets.
13. Remove metal bars (H) from fixture frame by removing screws (I)
as shown in diagram 3.
14. Install glass panels (K) to fixture frame by securing with metal
bars (H) and screws (I) using provided wrench (J).
NOTE: Do not overtighten otherwise glass could become damaged.
15. Install glass panel (L) to fixture frame by securing with metal
bars (H) and screws (I) using provided wrench (J).
NOTE: Do not overtighten otherwise glass could become damaged.
FOR OUTDOOR/WET LOCATION INSTALLATION:
16. Using silicon compound, apply a small bead where backplate meets
the wall to prevent water from entering.
NOTE: Large gaps will need to be corrected before applying
silicon compound.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do
not use abrasive or chemical agents.
US
M
L
I
D
S
E
T
Diagram 1
Diagram 2
Diagram 3
E F G
J
H
KL
I
DCB
Bulbs not included
A
  • Page 1 1
  • Page 2 2

VISUAL COMFORT CHO2935AI-CG User manual

Type
User manual

VISUAL COMFORT CHO2935AI-CG is a Fresno Medium 2-Light 3/4 Wall Lantern designed for outdoor or wet locations. It requires two light bulbs (not included) and features a sturdy construction with a mounting plate, support cable, and ground wire for secure installation. The lantern's elegant design includes glass panels, metal bars, and screws for easy assembly. With its stylish appearance and weather-resistant properties, this lantern is an excellent choice for illuminating your outdoor spaces.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI