VISUAL COMFORT S5177 User manual

Type
User manual

VISUAL COMFORT S5177 is a large linear lantern designed for indoor use. It features a stylish design with a canopy, mounting plate, and rods for easy installation. The fixture can accommodate multiple light bulbs, providing ample illumination for your living space. With its adjustable height and versatile design, the VISUAL COMFORT S5177 is a perfect choice for adding a touch of elegance to your home décor.

VISUAL COMFORT S5177 is a large linear lantern designed for indoor use. It features a stylish design with a canopy, mounting plate, and rods for easy installation. The fixture can accommodate multiple light bulbs, providing ample illumination for your living space. With its adjustable height and versatile design, the VISUAL COMFORT S5177 is a perfect choice for adding a touch of elegance to your home décor.

1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove mounting plate (B) from canopy (G) by removing collar
ring (H).
3. Using the mounting plate (B) as a guide, line up with the ceiling
and mark anchor positions.
4. Using a drill bit slightly smaller than the anchor, drill holes in the
marked positions. Install anchors (A) into the holes using hammer.
5. Install mounting plate (B) to junction box and secure with
mounting screws (C), then secure wood screws (D) to anchors (A).
6. Install canopy (G) to mounting plate (B) by securing with collar
ring (H).
7. Place top glass shades (J) onto top glass holders.
NOTE: It is recommended to have a helper assist in supporting the
fixture for steps 8-9.
8. Feed fixture wire and ground wire through bottom rods (I) and top
rods (F).
Presidio Large Linear Lantern
Item # S 5177
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
NOTICE:
Phillips Screwdriver Slotted Screwdriver Wire Strippers
Wire Cutters Hammer Pencil
Drill
Bulb not included
Q
A
BE
P
P
H
Diagram 1
H
C
D
I
P
J
K
M
N
O
F
G
I
PERSONS REQUIRED: Two
Presidio Large Linear Lantern
Item # S 5177
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
9. Connect bottom rods (I) to top rods (F), then attach to fixture loops (K)
and hooks (E). Secure links (P) at ends of rods.
NOTE: Ensure there is no tension on the wires. Cut excess wires,
being sure to leave enough to reach the junction box.
10. Separate two sides of molded wire, and strip insulation on each 5/8".
11. Loosen collar rings (H) and let canopy (G) slip down rods carefully.
12. Wrap fixture ground wire (bare copper) around the green grounding
screw (see diagram 1). Tighten. Continue fixture ground wire and
connect to supply ground wire (usually green or bare copper) using
wire nut (Q).
NOTE: It is imperative that the fixture is grounded.
13. Connect fixture neutral wire (ribbed) to the supply neutral wire
(usually white) using wire nut (Q).
14. Connect fixture hot wire (smooth with markings) to the supply hot
wire (usually black) using wire nut (Q).
CAUTION: Do not reverse the hot and neutral connections.
15. Make sure all wire connections are tight, then carefully tuck into the
junction box.
16. Install canopy (G) to mounting plate (B) by securing with collar
ring (H).
17. Remove rubber washers (N) and socket rings (Q) from the sockets,
then install glass shades (M) to socket holders and secure with
rubber washers (N) and socket rings (Q).
NOTE: Do not overtighten otherwise shade could become damaged.
18. Install light bulbs into the sockets.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do
not use abrasive or chemical agents.
NOTICE:
Bulb not included
Q
A
BE
P
P
H
Diagram 1
H
C
D
I
P
J
K
M
N
O
F
G
I
  • Page 1 1
  • Page 2 2

VISUAL COMFORT S5177 User manual

Type
User manual

VISUAL COMFORT S5177 is a large linear lantern designed for indoor use. It features a stylish design with a canopy, mounting plate, and rods for easy installation. The fixture can accommodate multiple light bulbs, providing ample illumination for your living space. With its adjustable height and versatile design, the VISUAL COMFORT S5177 is a perfect choice for adding a touch of elegance to your home décor.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI