Toro TX 427 and TX 525 Snow Thrower Power Kit, Compact Tool Carrier Installation guide

Type
Installation guide
FormNo.3441-209RevB
TX427andTX525SnowThrowerPowerKit
CompactToolCarrier
ModelNo.144-2512
InstallationInstructions
Installation
PreparingtheMachine
1.Parkthemachineonalevelsurface.
2.Lowertheloaderarms.
3.Shutofftheengineandremovethekey.
4.Openthehoodandsecureitwiththeproprod.
RemovingtheFusePanel
TX525Only
1.Pullthehairpincotterfromthebottomendofthe
hoodprop-rodandslidetheproprodoutofthe
retainingbracketsandtheprop-rodtab.
g004984
Figure1
1.Prop-rodtab4.Retaining
bracket—bottom
2.Retainingbracket—top5.Hairpincotter
3.Proprod
2.Removethe4screwssecuringthefusepanel
andthenpullthepaneloutanduptoremoveit.
g004985
Figure2
1.Fusepanel
2.Screw
©2020—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.T oro.com.
OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved
*3441-209*
Installingthe12VReceptacle
WARNING
Usingadrillwithoutpropereyeprotectionmayallowdebristoentertheeye,causinginjury.
Whendrillingorcarryingoutotheroperation,alwaysweareyeprotection.
1.Markanddrillahole(1-5/32inchdiameter)intothecontrolinthelocationshowninFigure3orFigure4.
Note:Ifyoudonothavea1-5/32inchdrillbit,usea1-1/8inchdrillbittodrilltheholeandthengrind
theholetoexpandit.
g331119
Figure3
TX427
g331151
Figure4
TX525
2.Removethelockingringfromthe12Vreceptacle.
3.Installthe12Vreceptacleintheholeandsecureitwiththelockingring.
g331165
Figure5
1.Lockingring2.12Vreceptacle
2
InstallingtheWire
Harnesses
g333594
Figure6
1.WireharnessinstalledonTX4272.WireharnessinstalledonTX525
1.Installthepostconnectorsfromtheportwire
harnesstothepostsonthe12Vreceptacle.
g311406
Figure7
1.Negative(-)connector3.Positive(+)connector
2.Negative(-)post4.Positive(-)post
2.Connecttheportwireharnesstoanoutgoing
powerconnector(endwith2connectors)ofthe
splitterharness.
g331130
Figure8
1.Portwireharness
3.Splitterharness
2.Outgoingpower
connectors
4.Accessoryconnectorof
machinewireharness
3.Connecttheotherendofthesplitterharnessto
anaccessoryconnectoronthemachinewire
harness.
Note:Ifnoconnectorsareopenonthemachine
wireharness,unpluganaccessoryfromthe
machinewireharnessandplugitintotheother
outgoingpowerconnectorofthesplitterharness.
4.FortheTX525,installthefusepanel.
Note:ReversetheprocedureforRemovingthe
FusePanel(page1).
5.Closethehood.
3
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Toro TX 427 and TX 525 Snow Thrower Power Kit, Compact Tool Carrier Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI