LOCKWOOD (ASSA ABLOY) EL110 Technical Manual

Brand
LOCKWOOD (ASSA ABLOY)
Model
EL110
Type
Technical Manual

LOCKWOOD (ASSA ABLOY) EL110

The LOCKWOOD (ASSA ABLOY) EL110 is a cabinet lock designed for use in weather-protected areas. It is supplied in "Power-to-Open" configuration as the initial factory setting, but can be reconfigured to "Power-to-Lock" (Fail Safe).

The lock is powered by a 12 VDC, 24 VDC, or 48 VDC supply and draws 175 mA, 88 mA, or 45 mA respectively. It has a 5-year limited warranty against defects in manufacture, workmanship, or materials.

The EL110 is designed to be fitted into cabinets and lockers with swing or sliding doors and can be mounted on the inside of the cabinet. The lock and striker dimensions are shown in Fig. 3 of the installation instructions.

LOCKWOOD (ASSA ABLOY) EL110

The LOCKWOOD (ASSA ABLOY) EL110 is a cabinet lock designed for use in weather-protected areas. It is supplied in "Power-to-Open" configuration as the initial factory setting, but can be reconfigured to "Power-to-Lock" (Fail Safe).

The lock is powered by a 12 VDC, 24 VDC, or 48 VDC supply and draws 175 mA, 88 mA, or 45 mA respectively. It has a 5-year limited warranty against defects in manufacture, workmanship, or materials.

The EL110 is designed to be fitted into cabinets and lockers with swing or sliding doors and can be mounted on the inside of the cabinet. The lock and striker dimensions are shown in Fig. 3 of the installation instructions.

EL110 SERIES CABINET LOCK
INSTALLATION INSTRUCTIONS
DRAWINGS NOT TO SCALE. INFORMATION IN THIS DATASHEET MAY BE CHANGED WITHOUT NOTICE.
An ASSA ABLOY Group brand
IMPORTANT NOTE: Lock is designed to be fi tted into cabinets and lockers etc with swing or sliding doors.
Lock is supplied in “Power-to-Open” confi guration as the initial factory setting.
Striker may engage with lock from side or front.
Front Enagement : see Fig.1
Side Engagement : see Fig.2
Mount lock on inside of cabinet, connect wiring (see Electrical Specifi cation) and power up lock. Lock and striker
dimensions are shown in Fig.3. Allow suffi cient space betwen lock unit and cut-out for wires as bunching of wires
may cause unit to malfunction.
Adjust the striker horizontally and vertically to ensure the striker locking recess engages with locking pin in the
lock.
Open and close the door several times, and readjust striker if necessary to achieve a smooth closing operation.
Confi gure lock mode of operation (see Fig.4). Lock may need to be removed temporarily to be reconfi gured.
When lock and striker is in place, remove fi lm from double-sided tape on solenoid and affi x faceplate onto lock.
1.
2.
3.
4.
5.
6.
ELECTRICAL SPECIFICATIONS
Solenoid Leads Colour
Red
Blue
Black
Supply Voltage
12 VDC
24 VDC
48 VDC
Current Draw
175 mA
88 mA
45 mA
CAUTION! Incorrect supply voltage may cause damage not cov-
ered by warranty. Please check supply voltage with a suitable meter
to ensure it is within +/- 15% of the nominal voltage shown above
with the strike powered.
This product has been designed for use in weather protected areas
only. DO NOT OIL OR LUBRICATE.
Fig. 3 - Lock and Strike Dimensions
18
39.9
31
R4
4.5mm Horizontal
Adjustment
22.5
5mm Sliding
Vertical Adjustment
55
13.5
21.5
30
72.7
28
Fig. 1 - Front Engagement
37
To prevent over- or
under-travel, set
distance between
back mounting face
of lock and striker
to 37mm.
Striker
Lock
Fig. 2 - Side Engagement
11
To prevent over- or
under-travel, set
distance between
back mounting face of
striker and centre of
nearest fi xing hole of
lock to 11mm.
Lock
Striker
Fig. 4 - Changing Mode of Lock Operation
Remove two rear solenoid fi xing screws.
Remove solenoid, spring and wire.
Confi gure solenoid, spring and wire depending on the
lock mode required, as shown below.
•
•
•
For Power-to-Lock (Fail Safe), reinsert using the
two lower solenoid fi xing screw holes.
For Power-to-Open (Fail Secure), reinsert using
the two upper solenoid fi xing screw holes.
Wire
Long Spring
Short Spring
Power-to-Lock
(Fail Safe)
Power-to-Open
(Fail Secure)
DA0015, Issue 4: 2nd Apr 2007
ASSA ABLOY Australia
2/16 Atkinson Road
Taren Point 2229
NSW, Australia
www.assaabloyasiapacifi c.com
warranty
5 Year Limited Warranty
ASSA ABLOY Australia guarantees for a period of 5 years in accordance with Trimec’s Standard Warranty Conditions, against defects in manufacture, workmanship or materials, provided that all
electrical and mechanical installation requirements are adhered to as per this datasheet. All third party and consequential claims are expressly excluded from this warranty.
  • Page 1 1
  • Page 2 2

LOCKWOOD (ASSA ABLOY) EL110 Technical Manual

Brand
LOCKWOOD (ASSA ABLOY)
Model
EL110
Type
Technical Manual

LOCKWOOD (ASSA ABLOY) EL110

The LOCKWOOD (ASSA ABLOY) EL110 is a cabinet lock designed for use in weather-protected areas. It is supplied in "Power-to-Open" configuration as the initial factory setting, but can be reconfigured to "Power-to-Lock" (Fail Safe).

The lock is powered by a 12 VDC, 24 VDC, or 48 VDC supply and draws 175 mA, 88 mA, or 45 mA respectively. It has a 5-year limited warranty against defects in manufacture, workmanship, or materials.

The EL110 is designed to be fitted into cabinets and lockers with swing or sliding doors and can be mounted on the inside of the cabinet. The lock and striker dimensions are shown in Fig. 3 of the installation instructions.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents