Intellinet Network IP Camera User guide

Brand: Intellinet

Model: Network IP Camera

Category: Security cameras

Type: User guide

Network IP Camera

User’s Guide R1.2

NETWORK IP CAMERA User’s Guide

Network IP Camera User’s Guide

Revision 1.2

Dated: SEP 2002

This Manual is for Intellinet Network IP Camera firmware version firm0030-161. If your

camera have the later version of firmware, please download the last updated user’s guide form

Intellinet’s homepage (www.intellinet-network.com)

FCC Compliance Statement

Caution: Any changes or modifications not expressly approved by the party responsible fo

compliance could void the user’s authority to operate the equipment.

OTE: This equipment has been tested and found to comply with the limits fo

a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

rotection against harmful interference when the equipment is operated in a commercial

environmental. This equipment generates, uses,, and can radiate radio frequency energy and, if no

installed and used in accordance with the instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at own expense.

Warning

This is a class “A” product. In a domestic environment, this product may cause radio interference

in which case the user may be required to take adequate measures.

Intellinet Network IP Camera contains portions of imaging code owned and copyrighted by Pegasus

NETWORK IP CAMERA User’s Guide

Important Notice

1. Camera surveillance laws may differ for each country. Therefore, please contact the local region

first to avoid any surveillance law violations and to apply for authorized purposes only.

2. Network IP Camera is for indoor use. Therefore note that the CMOS lens assembled to the

product can be damaged permanently if the camera lens is exposed to direct sunlight. When you

place Network IP Camera under the glaring light, we recommend using an iris lens. If your

application demands prolonged exposure to sunlight, you should consider to equip with a sun

visor.

3. Network IP Camera is not weatherproof. Therefore you should be well aware of environmental

specifications that are included in the manual. In case of outdoor use, where it needs additional

weather criteria, you should equip weatherproof case to protect Network IP Camera from water,

moisture, or temperature (higher or lower than specification). For Network IP Camera cleaning,

gently wipe with clean dry cloth.

4. Be sure to use a DC adapter that is provided by your dealer. Connecting Network IP Camera

directly to an AC current may cause electric damages to Network IP Camera.

5. Be caution in handling Network IP Camera for physical shocks may occur serious damage.

6. Be sure to attach Network IP Camera tight and stable to avoid any human injures when you

install Network IP Camera. Be cautious to locate on safety places where children are

unreachable.

7. If Network IP Camera does not operate properly, please contact the closest local Network IP

Camera distributor for after sales service. In all cases, you are prohibited to disassemble the

product. If so, intellinet is not responsible for malfunction nor service warranty.

NETWORK IP CAMERA User’s Guide

TABLE OF CONTENTS

PRODUCTION OVERVIEW 6

1.1 A

BOUT NETWORK IP CAMERA 6

1.2 MAIN FEATURES AND BENEFITS 7

2 PHYSICAL DESCRIPTION 8

2.1 C

ONTENTS 8

2.2 TOP VIEW AND DESCRIPTION 9

2.3 REAR VIEW AND DESCRIPTION 10

3 INSTALLATION SUMMARY, CONNECTING & PLACING 11

3.1 I

NSTALLATION SUMMARY 11

3.2 CONNECTING & PLACING 11

4 ASSIGNING IP ADDRESS & ACCESSING NETWORK IP

CAMERA’S HOMEPAGE 12

4.1 A

SSIGNING IP ADDRESS 12

4.2 ASSIGNING IP ADDRESS BY USING IP INSTALLER. 14

4.2.1 C

ONNECTING NETWORK IP CAMERA TO PC 14

4.2.2 IP INSTALLER 15

4.2.3 STARING A IP INSTALLER 15

4.3 A

SSIGNING IP ADDRESS BY USING HYPER TERMINAL 17

4.3.1 C

ONFIGURING HYPER TERMINAL 17

4.3.2 ASSIGNING IP ADDRESS 19

4.4 A

CCESSING NETWORK IP CAMERA HOMEPAGE 22

4.4.1 S

TARTING WEB BROWSER 22

4.4.2 LOGIN PAGE 22

4.4.3 NETWORK IP CAMERA’S HOMEPAGE 26

5 ADJUSTING THE CAMERA LENS 29

NETWORK IP CAMERA User’s Guide

5.1 ADJUSTING THE FOCUS 29

5.2 REPLACING THE LENS 30

6 CONFIGURING ADMINISTRATION TOOLS 31

6.1 A

DMINISTRATION TOOLS OVERVIEW 32

6.2 IMAGE CONFIGURATION 33

6.3 NETWORK CONFIGURATION 35

6.4 ADMIN, USER CONFIGURATION 35

6.5 EVENT TRIGGER CONFIGURATION 41

6.6 TIME CONFIGURATION 45

6.7 SYSTEM CONFIGURATION 46

7 PTZ CONTROL 48

APPENDIX 48

A. T

ECHNICAL SPECIFICATIONS 49

B. FAQ 51

C. T

ROUBLE SHOOTING 54

D. UTILIZING IP ADDRESSES ON LOCAL NETWORK 57

NTRODUCTION 57

IP CONSTRUCTION AND NETWORK CLASS 57

C CLASS NETWORK 58

E. U

PDATING NETWORK IP CAMERA’S NEWLY UPGRADED PROGRAM 61

OWNLOAD A NEWLY UPGRADED FIRMWARE 61

IDENTIFY THE VERSION OF FIRMWARE 61

UPGRADING THE NEWLY NETWORK IP CAMERA’S FIRMWARE 61

F. T

HE I/O CONNECTOR 63

G. RS 232 CABLE 64

H. H

IGH SPEED SOLUTIONS 65

I. REINSTATING THE FACTORY DEFAULT SETTINGS 67

J. GLOSSARY OF TERMS 69

NETWORK IP CAMERA User’s Guide

1 Production Overview

1.1 About Network IP Camera

Network IP Camera is the digital web server camera. This innovative camera combines a digital

camera and a network savvy computer to put live digital images on-line and make remote locations

immediately accessible through standard web browsers.

Network IP Camera is all-in-one equipped cutting-edge technology product, which contains digital

color camera, web-server functionality, optimized hardware for image compression, and physical

Ethernet connection. Therefore it does not need any extra S/W or H/W. Simply provide power and

connect Ethernet Cable.

Network IP Camera has wide range of applications to monitor places and objects. The most common

applications are construction area, important equipment, banks, hospital, amusement park, traffic

jammed highway, and baby care center. Therefore, you can conveniently monitor any place through

web browsers from the remote sites.

NETWORK IP CAMERA User’s Guide

1.2 Main Features and Benefits

Convenient Operation

Network IP Camera does NOT need the extra S/W such as a PC frame grabber nor interact with any

other server. The only software needed is Microsoft Internet Explorer 4.x or above and Netscape

Network IP Camera 4.x, which has web browser. The only step has to take is to assign a valid IP

address.

Open Standard Environment

Supporting TCP/IP networking, SMTP e-mail, HTTP and other Internet-related protocols; Network IP

Camera can be used in mixed operating system environment, such as, Windows, Unix, Mac and OS/2.

It integrates easily into other www/Intranet applications and CGI scripts.

Simple Administration

Using a standard Web browser, you can configure and manage Network IP Camera directly from its

own Web pages. And also, when a new firmware release becomes available, you can simply upgrade

all of your Network IP Camera products remotely over the network.

Various External Device Connection Supports

Supporting an auxiliary Input / Output Connector, you can connect your Network IP Camera to a

variety of external devices; such as, IR-sensors, switches, alarm relays. In combination with the

programmable alarming facilities, you can quickly develop various security applications that are

triggered on time or alarm-based events.

Security

Network IP Camera includes a self-contained Web Server, which means that digital images

can be secured like any other Internet host. Data protection is normally implemented by your

Network Administrator using the unit’s security settings in combination with an organization’s

Internet firewall. The Administrator can decide whether individuals, groups, the whole

company or the whole world may access your camera. Network IP Camera supports multi-

user password protection

Compression and Performance

With an adaptive frame rate dependent on the prevailing lighting conditions, Network IP

Camera delivers JPEG images at up to 30 images per second,

NETWORK IP CAMERA User’s Guide

Complimentary Software

 IP installer – for quick installation of multiple units

 Multi-Viewer (for 4 camera View)

 Active X control (required for Microsoft Internet Explorer)

 Java Applet for use with Internet Explorer when Active X cannot be used.

2 Physical Description

2.1 Contents

Check all items packed inside the box as below.

ITEM DESCRIPTION REMARKS

Network IP

Camera

Network Camera

AC Adapter &

Power Cable

Input: Free voltage

Output: DC 12V, 1A

Black Cable

RS232 Cable

D-Sub 9pin Black Cable

GPIO Connector

GPIO Terminal Block Assembled

Lens

6mm, F1.8 C mount Assembled

User’s Guide

Network IP Camera User’s Guide Printed Material

Program CD

IP installer, Manual CD

Bracket

Wall & Table attached Bracket Iron Material

* You can use a general camera stand or tripod for Network IP Camera.

NETWORK IP CAMERA User’s Guide

2.2 Top View and Description

Image Capture LED (Red): This LED indicates the status of image capture. Image Capture LED

flashes while users are seeing the images from Network IP Camera’s homepages. When it flashes once,

it means that the one captured image sent to the user.

Power LED (Red): This LED indicates the status of power on. After the power is supplied to Network

IP Camera, this Red LED is on.

Operating Status LED (Green): This LED indicates Network IP Camera’s Operating status. After

power is supplied, it is on for the first 15-20 seconds, and then it blinks once at every one second as

long as the power is connected properly.

Network Packet Transmit LED (Green): This LED indicates the status of networking. After the

Ethernet cable is connected, it is on.

Power LED Ima

e Ca

ture LED

Ope

Status

LED

Netwo

rk P

NETWORK IP CAMERA User’s Guide

2.3 Rear View and Description

Power Connector: To supply power to Network IP Camera. Use it with AC Adapter together.

You are highly recommended to use AC Adapter provided by your dealer to avoid any possible

damage from electric shock.

Network Connector: To connect 10baseT Ethernet or 100Fast Ethernet cable.

GPIO Connector

: To connect external devices such as infrared Sensor or Alarm Sensor etc. use with

provided terminal block. Refer to chapter “Appendix F. I/O Connector ”

RS232 Cable Connector: To connect external devices such as external camera, pan/tilt/zoom

mechanism, etc. Refer to Chapter “Appendix G. RS 232 Cable”

Network Connector RS 232 Connector

Power Connector

GPIO Connector

NETWORK IP CAMERA User’s Guide

3 Installation summary, Connecting & Placing

3.1 Installation Summary

 Connect Ethernet and Power to Network IP Camera on local network for configurations

 Install a Installation program “IP-Installer” for Network IP Camera in to a PC on local network

 Assign an IP address to Network IP Camera and configure administrator’s conditions

 Place Network IP Camera for your purpose, and re-connect power and Ethernet

 Adjust the Focus

3.2 Connecting & Placing

 Connect Ethernet line to the Ethernet port in the rear of Network IP Camera

 Connect the power supply to a power supply port in the rear of Network IP Camera.

 Confirm that the power LED, Operating Status Indictor blinks.

 Place Network IP Camera appropriately for you purpose

WARNING

etwork IP Camera is for indoor use. The built in CMOS (Complementary Metal Oxide

Semiconductor) can be damaged permanently if the camera lens is exposed to direct sunlight.

When Network IP Camera is placed under glaring light, and iris lens is recommended.

If your application demands prolonged exposure to sunlight, consider using a sun visor.

NETWORK IP CAMERA User’s Guide

4 Assigning IP Address & Accessing Network IP Camera’s

Homepage

4.1 Assigning IP Address

To able to access Network IP Camera, you should assign an appropriate IP Address firstly.

Terminology

• IP Address:

IP address is an identification code for computers and devices on a TCP/IP network. Networks

Using TCP/IP protocol route messages based on the IP address of the destinations. Within a closed

network. IP addresses can be assigned at random as long as each one is unique. However,

connecting a private network to the Internet requires using registered IP address to avoi

duplicates.

IP address can be acquired from a network administrator or an Internet service provider.

unique MAC address can be found on the label at the bottom of each Network IP

e should be used if a

ediary between the Network IP Camera and PC

amera

UB is not necessary to connect Network IP Camera to a PC if a

• MAC (Ethernet) Address (Media Access Control Address)

MAC address is a hardware identification code that uniquely identifies each node of a network.

The MAC layer interfaces directly with the network media. Consequently, each type of netwo

media requires a different MAC layer. The MAC address of Network IP Camera is a 12-digit

number. A

Camera

• Direct (Non Crossover) UTP Cable:

A common UTP cable (Twisted Pair Category 5 Cable) to connect devices such as a PC or

Network IP Camera that has an Ethernet port (RJ-45 port). The direct cabl

HUB is used as an interm

• Crossover UTP Cable

A specially designed UTP cable to connect two devices directly like connecting a PC and C

through Ethernet port. A H

crossover cable is use

Important

• Must use the newly assigned IP address, do NOT use occupied IP address, and not use the

default or example IP address .

• It is highly recommended to assign IP address before you place Network IP Camera on remote

place or remote network. Otherwise, some errors may occur while assigning IP address

NETWORK IP CAMERA User’s Guide

-NOTE-

IP addresses with any connection

If the camera system is connected to the Internet, IP addressing is a potential

roblem. There are two types of IP address, static and dynamic. Internet access

through an ISP (I

nternet Service Provider) usually means a dynamic IP address, and

a static IP address is much more desirable for a camera system. With a static IP

address the camera system can be located and viewed by any browser by typing the

IP address as the location to open. But dynamic IP addresses chance, so the users

will have difficulty finding the camera. When connecting to a company network, a

dynamic address can be avoided easily. When connecting via an ISP, static IP

addresses carry additional charges, if they are available at all. Alternative schemes to

'redirect' user to the camera each time the IP address changes are possible, so this

area is likely to become easier in the future.

NETWORK IP CAMERA User’s Guide

4.2 Assigning IP address by using IP installer.

4.2.1 Connecting Network IP Camera to PC

At first, you need to install an IP installation program (IP Installer.exe) on your PC that is

connected on the same local network as Network IP Camera.

1) Connecting with direct cable (Non Crossover UTP cable)

In this case, you have to use a HUB to connect Network IP Camera and a PC to assign IP address or

you should have an Ethernet Cable to connect the Network IP Camera, and a PC that is already

connected with Ethernet Cable.

2) Connecting with Crossover UTP Cable

Use the crossover to directly connect Network IP Camera to a PC. This connection is to be used to

configure Network IP Camera.

*It is highly recommended that you assign IP address to Network IP Camera with crossover

cable.

User PC

Web-View

Ethernet HUB

Direct UTP

Cable

Connect Network IP Camera

to a PC through a HUB

User PC

Web-View

Ethernet HUB

Crossover UTP Cable

Connect Network IP Camera

directly to a PC through LAN

orts.

Direct UTP

Cable

NETWORK IP CAMERA User’s Guide

4.2.2 IP Installer

To install an IP address, you should use the IP Installer provided with Network IP Camera.

You can download its program through the web site (http://intellinet-network.com)

4.2.3 Staring a IP Installer

Firstly, install an IP-Installer program on your PC that is connected on the same local network

as Network IP Camera. And click it. You can only setup a Network IP Camera that is connected

on a local network.

①

Execute IP Installer after Network IP

Camera completes its booting (Wait

until the operating LED blinks every

in a second periodically).

② When the IP-installer is executed,

the panel shows every Network IP

Camera connected at the local network.

From the Network IP Camera listed,

select one to assign a new IP address

(Every Network IP Camera has factory

default IP address).

Note the MAC Address found on the

underside label of Network IP Camera.

To choose a Network IP Camera,

click on its list.

③ Enter the Admin’s ID and Password

in the blank (Default Admin’s ID and

Password are all “admin”) to assign

(or change) IP Address for Network IP

Camera and set up.

Note: System required for IP installer; Microsoft Windows9X/NT/2000

NETWORK IP CAMERA User’s Guide

④ Enter the IP address, Gateway address, Subnet Mask address, DNS Server address and Server IP

address that is assigned from network administrator in blank of “New IP address”, Gateway

Address and others. (When the addresses are not assigned properly, you cannot access Network IP

Camera remotely. Even on the local network, you are not able to access if you do not assign an IP

address to Network IP Camera properly).

⑤ Server IP Address represents an IP address of PC, which is being executed upgrade program when

you have Network IP Camera upgraded. (Please refer to Chapter ’E Updating Network IP

Camera’s newly upgraded Program).

After entering all addresses for Network IP Camera, click on “Change Network Configurations”

button.

⑥ The Success message shows up if all the

information is set up properly. Then click

“OK”button.

NOTE

After changing Network Configuration for Network IP Camera, It will take a little time to

reboot Network IP Camera

y itself so that you may access Network IP Camera’s

Homepage after checking the Operator LED blinks.

NETWORK IP CAMERA User’s Guide

4.3 Assigning IP Address by using Hyper Terminal

In case you do NOT assign IP address by using IP Installer, you can assign IP address by using

Hyper Terminal. In this case, you should configure Hyper Terminal condition first.

4.3.1 Configuring Hyper Terminal

Hyper Terminal is a basic program for Windows 9x/NT/2000. PC can communicate with

external devices through the serial port by using this program. The steps you should take to set

the Hyper Terminal are as follows in the case of Windows 2000 OS.

① Start  Programs  Accessories 

Communications  Hyper Terminal. Select

one among the icons and then enter an

appropriate name in the Name edit box.

② Select a serial port of PC, then click “OK”

button. (Usually COM1 or COM2 is

recommended)

NETWORK IP CAMERA User’s Guide

③ Configure bit/sec as 38400 and leave others as

default values.

④ The panel shows up like on the right side when

you configure properly. (If it doesn’t, please try

again from beginning)

NETWORK IP CAMERA User’s Guide

4.3.2 Assigning IP Address

Follow the below steps to assign IP address by using Hyper Terminal

① Execute “Hyper Terminal” on your PC

② Connect RS232 Cable to the serial port of PC that you have selected in ‘4.3.1 Configuring Hyper

Terminal’ and Network IP Camera serial port while Hyper Terminal is executed.

③ Supply the power to Network IP Camera.

④ After a while, the count down starts with the message “Press 'p' key to stop auto-boot or Load-

Default-Button under the NetCam for 3 seconds...”

At this time, press ‘p’ key. Then, [Network IP Camera Boot] prompt shows like the below image.

⑤ You can see Network Configuration while [Network IP Camera Boot] Prompt is running by

pressing ‘p’ key again.

NETWORK IP CAMERA User’s Guide

Here, inet on ethernet (e), host inet (h) and gateway inet (g) values are network configuration values.

You should change these values in most case. If you don’t know what value you should assign, refer to

the network administrator.

Inet on ethernet (e) is IP address and subnet mask address of Network IP Camera. IP address and

subnet mask addresses are separated by colon (:). For example, IP address is represented by decimal

numbers delimited by dot (.) like ‘192.168.1.27’. Hexadecimal numbers like ‘ffffff00’ in the case of

‘255.255.255.0’ represents subnet mask address. Note that the numbers of subnet mask value are not

delimited by dot. See the example in the above picture.

Host inet (h) is the address to which Network IP Camera tries to connect to upgrade its firmware

program in flash memory. Network IP Camera first search this host on the network on booting

sequence. For more information on Network IP Camera upgrade, refer to “E. Updating Network IP

Camera’s Newly upgraded Program”.

Page is loading ...

Intellinet Network IP Camera User guide

Brand: Intellinet

Model: Network IP Camera

Category: Security cameras

Type: User guide

Download PDF

report

Intellinet Network IP Camera User guide

Intellinet Network IP Camera User guide

Related papers

Other documents