B-K lighting Yukon - Indirect Installation guide

Brand
B-K lighting
Model
Yukon - Indirect
Type
Installation guide

B-K lighting Yukon - Indirect is a steplight with integral LED driver suitable for wet locations. It has a die-cast aluminum housing with a powder coat finish and a frosted polycarbonate lens. The Yukon - Indirect is available in two sizes, small and large, and can be installed in concrete or wood surfaces. It comes with a 10-year warranty.

Here are some of the features and possible use cases for the B-K lighting Yukon - Indirect:

  • Suitable for wet locations, making it ideal for outdoor use in areas that are exposed to rain or snow.
  • Die-cast aluminum housing with a powder coat finish provides durability and resistance to corrosion.

B-K lighting Yukon - Indirect is a steplight with integral LED driver suitable for wet locations. It has a die-cast aluminum housing with a powder coat finish and a frosted polycarbonate lens. The Yukon - Indirect is available in two sizes, small and large, and can be installed in concrete or wood surfaces. It comes with a 10-year warranty.

Here are some of the features and possible use cases for the B-K lighting Yukon - Indirect:

  • Suitable for wet locations, making it ideal for outdoor use in areas that are exposed to rain or snow.
  • Die-cast aluminum housing with a powder coat finish provides durability and resistance to corrosion.
RELEASED
9/10/2020
REFERENCE NUMBER
INS-2817-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
TOOLS
NEEDED:
By Others
5/32” Allen Wrench
Waterproof Wire Connectors
Hand Held Drill 1/4 inch Drill Bit
YK - Yukon Indirect
Warning High Voltage Hot Surface
Yukon - Indirect
Integral Driver - LED
Standard Installation
· Suitable for wet locations
IMPORTANT LISTINGS AND CERTIFICATIONS
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel with appropriate personal protective
equipment must perform all servicing of this product.
• Before wiring to power supply and during servicing, turn off and
lock out power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL
SAFETY AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part,
as this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body.
• Replace LED assembly only with correct wattage and type
of power supply appropriate for LED assembly.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause
an unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY
TO PERSONS IMPORTANT
SAFETY INSTRUCTIONS
Lighted fixture is HOT!
WARNING - To reduce the risk of
FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing LED.
Fix ture ge ts HOT quickly! Contact only switch/plug when
turning on. Do not touch hot lens, guard, or enclosure.
Keep fixture away from materials that may burn.
Do not operate the luminaire fitting with a missing or
damaged shield. Do not touch the source at any time.
Use a soft cloth or gloves. Oil from skin may cause
damage.
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION
INSTRUCTIONS
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
RELEASED
9/10/2020
REFERENCE NUMBER
INS-2817-00
1. Remove 4 wing nuts and plastic sleeve from
housing and save for later use.
4. Drill four 1/4” holes at desired position on
concrete form. Please use 1-1 template
provided on page 4.
1. Remove plastic sleeve and all-threads by
removing wing nuts from housing.
2. Knock out one of the knockouts on the back
or side of the housing and install conduit (by
others).
5. Insert all-treads though the four 1/4” holes
drilled on the concrete form and hand tighten
the 4 wing nuts previously removed on step 1.
2. Remove faceplate from fixture by lifting from
the bottom up and save for later use.
3. Remove backplate by lifting strait up.
3. Insert plastic sleeve into housing previously
removed on step 1.
Phase 1 - Rough in
Phase 2 - Finish Installation
Yukon - Indirect
Integral Driver - LED
Standard Installation
4. Make watertight connections from line voltage to
fixture leads using waterproof wire connectors.
All line voltage connections must be
made in compliance with the National
Electrical Code. Failure to do so will
void warranty.
Fixture
LINELINE
GROUNDGROUND
COMCOM
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
RELEASED
9/10/2020
REFERENCE NUMBER
INS-2817-00
5. Once wiring is completed insert fixture into
housing.
6. Hand tighten screws using a 5/32” allen
wrench.
7. Insert Faceplate previously removed on Step
2.
8. Next insert faceplate previously removed on
step 2.
Yukon - Indirect
Integral Driver - LED
Standard Installation
FIXTURE
LINE
COM
GROUND
DIM +
DIM -
(0-10 Wiring Diagram)
All line voltage connections must be
made in compliance with the National
Electrical Code. Failure to do so will
void warranty.
Tamper Resistant Option
1. Tighen two #8-32 stainless steel set screws at
the bottom of the faceplate with a 5/64” allen
wrench.
.250
4.00
3.00
NOTES: Full Scale Anchor Bolt Template
WARNING!
Template must print at proper scale.
Verify dimensions prior to use.
!
WARNING!
Template must print at proper scale.
Verify dimensions prior to use.
!
.250
4.00
3.00
DRAWING NUMBER
Yukon - Indirect Commercial Steplight
D001620 TEMPLATE
9/10/20
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING AND ITS RECEIPT OR POSSESSION
DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR
SELL ANYTHING IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN
AUTHORIZATION OF B-K LIGHTING IS STRICTLY FORBIDDEN.
ALL DIMENSIONS INDICATED ON THIS SUBMITTAL ARE NOMINAL. CONTACT TECHNICAL SALES IF YOU
REQUIRE MORE STRINGENT DIMENSIONAL SPECIFICATIONS.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

B-K lighting Yukon - Indirect Installation guide

Brand
B-K lighting
Model
Yukon - Indirect
Type
Installation guide

B-K lighting Yukon - Indirect is a steplight with integral LED driver suitable for wet locations. It has a die-cast aluminum housing with a powder coat finish and a frosted polycarbonate lens. The Yukon - Indirect is available in two sizes, small and large, and can be installed in concrete or wood surfaces. It comes with a 10-year warranty.

Here are some of the features and possible use cases for the B-K lighting Yukon - Indirect:

  • Suitable for wet locations, making it ideal for outdoor use in areas that are exposed to rain or snow.
  • Die-cast aluminum housing with a powder coat finish provides durability and resistance to corrosion.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents