Triton Systems FT5000 Xscale Series Owner's manual

CORPORATE HEADQUARTERS: RMA (RETURN MATERIAL AUTHORIZATION)

R

ETURN A DDRESS:

522 E. Railroad Street 21405 Avenue “B”

Long Beach, MS 39560 Long Beach, MS 39560

PHONE: (228) 868-1317

FAX: (228) 868-0437

MODEL FT5000

A

UTOMATED TELLER MACHINE

SITE PREPARATION AND

INSTALLATION GUIDE

VERSION 4.0

TDN 07100-00004D 02/2006

COPYRIGHT NOTICE

TRITON WHERE MONEY COMES FROM, TRITON WAVES, DOVER and DO-

VER logo are registered trademarks of Delaware Capital Formation, Inc., a wholly-owned

subsidiary of Dover Corporation.

2

FEDERAL COMMUNICATIONS COMMISSION (FCC) COMPLIANCE

Statement of Compliance: This equipment complies with Part 68 of the FCC rules.

Located in the control area of the Automated Teller Machine (ATM) is the product

label. This label lists the FCC registration number and ringer equivalence number of

the unit. If requested, this information must be provided to the telephone company.

USCO/FIC Codes: When ordering service from the telephone company for the

FT5000 ATM, the following information should be supplied:

Universal Service Order Code (USOC): RJ-11C

The Facility Interface Code (FIC): 02LS2

Plug and Jack: The plug and jack used to connect this equipment to premise wiring

and telephone network must comply with the applicable FCC Part 68 rules and

requirements adopted by ACTA. A compliant telephone cord and modular plug is

provided with this product. The telephone cord is designed to be connected to a

compatible modular jack that is also compliant.

Ringer Equivalent Number (REN): The REN is used to determine the number of the

devices that may be connected to a telephone line. Excessive RENs on a telephone

line may result in the devices not ringing in response to an incoming call. In most but

not all areas, the sum of the RENs should not exceed five (5). To be certain of the

number devices that may be connected to a line, as determined by the local RENs,

contact the local telephone company.

Harm to the Network: If the FT5000 ATM causes harm to the telephone network, the

telephone company will notify the customer that a temporary discontinuous of

service may be required. If advanced notice is not possible, the telephone company

will notify the customer as soon as possible. You will be advised of your right to file

a complaint with the FCC if you believe it’s necessary.

Notification of Changes in Telephone Company Equipment: The telephone company

may make changes in its facilities, equipment, operations, or procedures that could

affect the operation of the equipment. If this happens, the telephone company will

provide advanced notice in order for you to make necessary modifications to maintain

uninterrupted service.

FT5000 - SITE PREPARATION AND INSTALLATION GUIDE

** CAUTION **

Changes or modifications not expressly approved by Triton

Systems could void the regulatory compliance approval

and the warranty. Use of this product in a manner other

than those described in this manual may result in personal

injury!

3

If the equipment is causing harm to the network, the telephone company may request

that you disconnect the equipment until the problem is resolved. Repairs should be

made only by qualified factory representatives.

Party Lines: The FT5000 ATM must not be used on party lines.

Alarm Equipment: The FT5000 ATM should have its own dedicated phone line. Do

not install the FT5000 on the same line as alarm equipment.

Electrical Safety Advisory: telephone companies report that electrical surges, typically

lightening transients, are very destructive to customer equipment connected to AC

power sources. This has been identified as a major nationwide problem. A

commercially available, power surge suppressor, is recommended for use with the

FT5000 to minimize damage in the event of an electrical surge.

CANADIAN IC COMPLIANCE

NOTICE:

The Industry Canada label identifies certified equipment. This certification means

that the equipment meets telecommunications network protective, operational and

safety requirements as prescribed in the appropriate terminal equipment technical

requirements document(s). The department does not guarantee the equipment will

operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be

connected to the facilities of the local telecommunications company. The equip-

ment must also be installed using an acceptable method of connection. The cus-

tomer should be aware that compliance with the above conditions may not prevent

degradation of service in some situations.

Repairs to certified equipment should be coordinated by a representative desig-

nated by the supplier. Any repairs or alterations made by the user to this equipment,

or equipment malfunctions, may give the telecommunications company cause to

request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections

of the power utility, telephone lines, and internal metallic water pipe system, if present,

are connected together. This precaution may be particularly important in rural areas.

Caution: Users should not attempt to make such connections themselves, but should

contact the appropriate electric inspection authority, or electrician, as appropriate.

FT5000 - SITE PREPARATION AND INSTALLATION GUIDE

Repairs and Returns: If telecom compatibility trouble is experienced with the FT5000

ATM, you may contact for repairs and warranty information: Triton at 1-228-868-

1317

Triton Systems of Delaware, Inc.

522 East Railroad Street

Long Beach, MS 39560

4

NOTICE:

The REN assigned to each terminal device provides an indication of the maximum

number of terminals allowed to be connected to a telephone interface. The termina-

tion on an interface may consist of any combination of devices subject only to the

requirement that the sum of the RENs of all the devices does not exceed 5.

AVIS:

L’étiquette d’Industrie Canada identific le matériel homologué. Cette étiquette certifie

que le matériel est conforme aux normes de protection, d’exploitation et de sécurité

des réseaux de télécommunications, comme le prescrivent les documents concernant

les exigences techniques relatives au matériel terminal. Le Ministère n’assure toutefois

pas que le matériel fonctionnera à la satisfaction de l’utilisateur.

Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le raccorder

aux installations de 1’entreprise locale de télécommunication. Le maté-riel doit

également être installé en suivant une méthode acceptée de raccordement. L’abonné

ne doit pas oublier qu’il est possible que la comformité aux conditions énoncées ci-

dessus n’empêche pas la dégradation du service dans certaines situations.

Les réparations de matériel homologué doivent être coordonnées par un représentant

désigné par le fournisseur. L’entreprise de télécommunications peut demander à

I’utilisateur de débrancher un appareil à la suite de réparations ou de modifications

effectuées par l’utilisateur ou à cause de mauvais fonctionnement.

Pour sa propre protection, l’utilisateur doit s’assurer que tous les fils de mise à la

terre de la source d’énergie électrique, des lignes téléphoniques et des canalisations

d’eau métalliques, s’fl y en a, sont raccordés ensemble. Cette précaution est

particulièrement importante dans les régions rurales. Avertissement: L’utilisateur ne

doit pas tenter de faire ces raccordements lui-même; il doit avoir recours à an service

d’inspection des installations électriques, ou à un électricien, selon le cas.

FT5000 - SITE PREPARATION AND INSTALLATION GUIDE

UNITED KINGDOM

This equipment has been approved in accordance with Council Decision 98/482/EC

for pan-European single terminal connection to the Public Switched Telephone

Network (PSTN). However, due to differences between the individual PSTNs pro-

vided in the different countries, the approval does not, of itself, give unconditional

assurance of successful operation on every PSTN network termination point. In the

event of problems, contact your equipment supplier in the first instance. This unit

uses only Dual-Tone Multi-Frequency (DTMF) address signaling.

5

EMISSIONS (EMI)

This device complies with Part 15 of the FCC rules. Operation is subject to the

following two (2) conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that

may cause undesired operation.

Note:

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to Part 15 of FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference

in which case the user will be required to correct the interference at his own expense.

Changes or modifications to this unit not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

CANADIAN EMISSION REQUIREMENTS

This digital apparatus does not exceed the Class A limits for radio noise emissions

from digital apparatus set in the Radio Interference Regulations of the Canadian

Department of Communications. This Class A digital apparatus complies with

Canadian ICES-003.

Le present appareil numerique n’emet pas de bruits radioelectriques depassant les

limites applicables aux appareils numeriques de la Class A prescrites dans le Reglement

sur le brouillage radioelectrique edicte par le ministere des Communications du

Canada. Cet appareil numerique de la classe A est conforme a la norme NMB-003

Canada.

UK / AUSTRALIAN EMISSION REQUIREMENTS

Warning:

This is a Class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

FT5000 - SITE PREPARATION AND INSTALLATION GUIDE

AVIS:

L’indice d’équivalence de la sonnerie (IES) assigné à chaque dispositif terminal

indique le nombre maximal de terminaux qui peuvent étre raccordés à une interface.

La terminaison d’une interface téléphonique peut consister en une combinaison de

quelques dispositifs, à la seule condition que la somme d’indices d’équivalence de

la sonnerie de tous les dispositifs n’exède pas 5.

6

FT5000 - SITE PREPARATION AND INSTALLATION GUIDE

What’s in This Installation Guide

This Installation Guide provides information for the preparation and installation of

the FT5000 ATM. It contains requirements for site preparation, electrical specifica-

tions, and cabinet accessibility that comply with all relevant codes, laws and regu-

lations. The Installation Guide is divided into the following sections:

 Introduction. Summarizes the basic steps that must be completed to physically

install a FT5000 ATM. Configuration of operating parameters is not covered!

Refer to the applicable Configuration and/or Service Manual for instructions

on configuring the operating parameters.

 ATM Installation for Accessibility. Describes the basic Americans with

Disabilities Act (ADA) requirements for ATM location and access. Note: These

are the general requirements that should be applicable to most installation

locations. Please verify the specific requirements with the state where the

ATM is to be installed, prior to installation. For state contact information, you

may call the ADA information line at 1-800-514-0301.

 ATM Environmental Precautions Checklist. Describes the general

environmental precautions considered when installing the ATM. To help ensure

proper operation of the ATM, ensure the environmental criteria listed in this

checklist are met.

 Site Preparation/Installation. Describes site preparation for exterior wall or

vestibule locations. Instructions provide dimensions/clearances needed to

install the FT5000 and procedures for installing the cabinet and front fascia.

NEW - Optional platforms (“plinths”) available in 2 sizes expediate raising

the unit, if needed. [ P/N 06100-00071 (2-3/8") and P/N 06100-00072 (4-

3/4")] Also, cabinets now come with their own leveling feet .

 Power and Communication. Describes how to connect the ATM to the facility

power and telephone connections.

 Dispensing Mechanism Installation. Describes how to install/remove the

dispensing mechanism into the ATM security cabinet.

 Installing the Rear Service Panel (RSP). Describes how to install and connect

the RSP to the cabinet sleeve.

 TCP/IP (Ethernet) Cable Installation. Describes where to install the

10Base-T CAT-5 cable for Ethernet communication.

 VSAT Cable Installation. Describes where to install the optional VSAT cable.

7

FT5000 - SITE PREPARATION AND INSTALLATION GUIDE

INTRODUCTION

This document contains the information necessary for the preparation and

installation of a FT5000 Triton ATM. It’s important that the site complies with the

requirements specified in this document. In addition, electrical wiring and

mechanical systems must also comply with all relevant laws and regulations.

The site must be prepared by the customer or his agent who is fully conversant

with the requirements of installing through-the-wall ATM equipment. The

responsibility for ensuring that the site is prepared in compliance with this

document remains with the customer.

For information and guidance only, a list is provided in general terms of those

matters for which the customer is responsible. The list is not intended to be

comprehensive and in no way modifies, alters, or limits the responsibility of the

customer for all aspects of adequate site preparation.

1. Location of the equipment and site preparation.

2. Site wiring (power, communication).

3. Location of other equipment that may cause electrical, electromagnetic, or

heat induced interference.

4. Make building alterations to meet wiring and other site requirements.

5. Install all communication cables, wall jacks, and associated hardware.

6. Provide and install necessary power distribution boxes, conduits and

grounds.

7. Ensure all applicable codes, regulations and laws (electrical, building, safety)

are adhered to.

8. Ensure the environmental requirements of this unit are met.

9. Install the unit at a height which meets the ADA accessibility regulations

for the state/country installed.

THIS PAGE INTENTIONALLY LEFT BLANK

8

FT5000 - SITE PREPARATION AND INSTALLATION GUIDE

9

ATM INSTALLATION FOR ACCESSIBILITY

A Guide to the New ADA-ABA Accessibility Guidelines

FT5000 - SITE PREPARATION AND INSTALLATION GUIDE

On July 23, 2004, the U.S. Access Board, an independent Federal agency,

issued updated accessibility guidelines for new or altered facilities covered by

Americans with Disabilities Act and the Architectural Barriers Act. These

guidelines address a wide range of facilities in the private and public sectors.

Presented here is an overview of the new guidelines that also highlights sig-

nificant changes.The following guidelines (305 and 308) pertain to floor/

ground space and reach ranges.

When will the new guidelines take effect?

The Board’s guidelines are not mandatory on the public, but instead serve as

the baseline for enforceable standards (which are) maintained by other Federal

agencies. In this respect, they are similar to a model building code in that they

are not required to be followed except as adopted by an enforcing authority.

Under the ADA, the Department of Justice (and in the case of transit facilities,

the Department of Transportation) are responsible for enforceable standards

based on the Board’s guidelines. These agencies will update their ADA stan-

dards based on the new guidelines. In doing so, they will indicate when the new

standards are to be followed. Several other agencies (the General Services Ad-

ministration, Department of Defense, Department of Housing and Urban Devel-

opment, and the U.S. Postal Service) hold a similar responsibility for standards

used to enforce the ABA.

Existing Facilities

The ADA and ABA guidelines cover new construction and planned alterations

and generally do not apply to existing facilities except where altered. Facilities

built or altered according to earlier versions of the ADA or ABA standards will

not necessarily have to meet the updated version except where they are subse-

quently altered or renovated. The Department of Justice, which regulates re-

quirements for existing facilities under the ADA, intends to address coverage of

facilities built or altered according to the original ADA standards in its rulemaking

to update the standards. It will also address facilities retrofitted under ADA

provisions for existing facilities, such as the requirement for barrier removal in

places of public accommodation. With respect to ABA facilities, the Board has

clarified in the guidelines that facilities built to earlier ABA standards are subject

to the new requirements only in relation to planned alterations.

10

ATM INSTALLATION FOR A CCESSIBILITY

305 Clear Floor or Ground Space

305.1 General. Clear floor or ground space shall comply with 305.

305.2 Floor or Ground Surfaces. Floor or ground surfaces of a clear floor or

ground space shall comply with 302. Changes in level are not permitted.

EXCEPTION: Slopes not steeper than 1:48 shall be permitted.

305.3 Size. The clear floor or ground space shall be 30 inches (760 mm) mini-

mum by 48 inches (1220 mm) minimum.

305.4 Knee and Toe Clearance. Unless otherwise specified, clear floor or

ground space shall be permitted to include knee and toe clearance com-

plying with 306.

305.5 Position. Unless otherwise specified, clear floor or ground space shall be

positioned for either forward or parallel approach to an element.

305.6 Approach. One full unobstructed side of the clear floor or ground space

shall adjoin an accessible route or adjoin another clear floor or ground

space.

Figure 305.3 Clear Floor or Ground Space

Figure 305.5 Position of Clear Floor or Ground Space

11

FT5000 - SITE PREPARATION AND INSTALLATION GUIDE

305.7 Maneuvering Clearance. Where a clear floor or ground space is located

in an alcove or otherwise confined on all or part of three sides, additional

maneuvering clearance shall be provided in accordance with 305.7.1 and

305.7.2.

305.7.1 Forward Approach. Alcoves shall be 36 inches (915 mm)wide mini

mum where the depth exceeds 24 inches (610 mm).

Figure 305.7.1 Maneuvering Clearance in an Alcove, Forward Approach

305.7.2 Parallel Approach. Alcoves shall be 60 inches (1525 mm) wide mini-

mum where the depth exceeds 15 inches (380 mm).

Figure 305.7.2 Maneuvering Clearance in an Alcove, Parallel Approach

308 Reach Ranges

308.1 General. Reach ranges shall comply with 308.

308.2 Forward Reach.

308.2.1 Unobstructed. Where a forward reach is unobstructed, the high forward

reach shall be 48 inches (1220 mm) maximum and the low forward reach

shall be 15 inches (380 mm) minimum above the finish floor or ground.

12

ATM INSTALLATION FOR A CCESSIBILITY

Figure 308.2.1 Unobstructed Forward Reach

308.2.2 Obstructed High Reach. Where a high forward reach is over an obstruc-

tion, the clear floor space shall extend beneath the element for a distance

not less than the required reach depth over the obstruction. The high for-

ward reach shall be 48 inches (1220 mm) maximum where the reach depth

is 20 inches (510 mm) maximum. Where the reach depth exceeds 20 inches

(510 mm), the high forward reach shall be 44 inches (1120 mm) maxi-

mum and the reach depth shall be 25 inches (635 mm) maximum.

Figure 308.2.2 Obstructed High Forward Reach

308.3 Side Reach.

308.3.1 Unobstructed. Where a clear floor or ground space allows a parallel ap-

proach to an element and the side reach is unobstructed, the high side

reach shall be 48 inches (1220 mm) maximum and the low side reach

shall be 15 inches (380 mm) minimum above the finish floor or ground.

EXCEPTIONS: 1. An obstruction shall be permitted between the clear floor or

ground space and the element where the depth of the obstruction is 10 inches (255

mm) maximum.

2. Operable parts of fuel dispensers shall be permitted to be 54 inches (1370 mm)

maximum measured from the surface of the vehicular way where fuel dispensers are

installed on existing curbs.

13

14

FT5000 - SITE PREPARATION AND INSTALLATION GUIDE

Figure 308.3.1 Unobstructed Side Reach

308.3.2 Obstructed High Reach. Where a clear floor or ground space allows a

parallel approach to an element and the high side reach is over an obstruc-

tion, the height of the obstruction shall be 34 inches (865 mm) maximum

and the depth of the obstruction shall be 24 inches (610 mm) maximum.

The high side reach shall be 48 inches (1220 mm) maximum for a reach

depth of 10 inches (255 mm) maximum. Where the reach depth exceeds

10 inches (255 mm), the high side reach shall be 46 inches (1170 mm)

maximum for a reach depth of 24 inches (610 mm) maximum.

EXCEPTIONS: 1. The top of washing machines and clothes dryers shall be permit-

ted to be 36 inches (915 mm) maximum above the finish floor.

2. Operable parts of fuel dispensers shall be permitted to be 54 inches (1370 mm)

maximum measured from the surface of the vehicular way where fuel dispensers are

installed on existing curbs.

Figure 308.3.2 Obstructed High Side Reach

15

ATM INSTALLATION FOR

ACCESSIBILITY

1. This document supersedes all other

information provided by Triton for

ATM installation for accessibility.

2. Information provided in this

manual is based on federal guide-

lines (ADA Accessibility Guidelines

for Buildings and Facilities –

ADAAG)as amended through

January 1998. You should verify it

has not been amended. States may

also have accessibility codes.

These codes may be more restric-

tive than the federal guidelines.

Please verify this with the state

where the ATM is to be installed

prior to installation. For state con-

tact information, you may call the

ADA information line.

3. For countries other than the US,

please use the guidelines for ac-

cessibility for that country.

4. A complete copy of the ADAAG

referred to here can be found at

http://www.access-board.gov. In-

cluded in this document is the sec-

tion of the ADAAG specifically for

ATMs. For additional information

on floor surfaces and other

ADAAG requirements, please see

the complete specification.

4.34 Automated Teller Machines.

4.34.1 General. Each machine re-

quired to be accessible by 4.1.3

shall be on an accessible route and

shall comply with 4.3.4.

4.34.2 Clear Floor Space. The auto-

mated teller machine shall be lo-

cated so that clear floor space com-

plying with 4.2.4 is provided to al-

low a person using a wheelchair to

make a forward approach, a parallel

approach, or both to the machine.

4.34.3 Reach Ranges.

(1) Forward Approach Only. If only a

forward approach is possible, operable

parts of all controls shall be placed within

the forward reach range specified in

4.2.5.

(2) Parallel Approach Only. If only a

parallel approach is possible, operable

parts of controls shall be placed as fol-

lows:

(a) Reach Depth Not More Than 10

inches (255 mm). Where the reach

depth to the operable parts of all con-

trols as measured from the vertical plane

perpendicular to the edge of the unob-

structed clear floor space at the farthest

protrusion of the automated teller ma-

chine or surround is not more than 10

inches (255 mm), the maximum height

above the finished floor or grade shall

be 54 inches (1370 mm).

ATM INSTALLATION FOR A CCESSIBILITY

16

FT5000 - SITE PREPARATION AND INSTALLATION GUIDE

(b) Reach Depth More Than 10 inches

(255 mm). Where the reach depth to

the operable parts of any control as mea-

sured from the vertical plane perpen-

dicular to the edge of the unobstructed

clear floor space at the farthest protru-

sion of the automated teller machine or

surround is more than 10 inches (255

mm), the maximum height above the fin-

ished floor or grade shall be as follows:

(3) Forward and Parallel Approach. If

both a forward and parallel approach

are possible, operable parts of controls

shall be placed within at least one of the

reach ranges in paragraphs (1) or (2) of

this section.

SNOITACIFICEPSYTILIBISSECCA

HTPEDHCAERTHGIEHMUMIXAM

sehcnI sretemilliM sehcnI sretemilliM

01552450731

110822/1350631

21503355431

310332/1255331

415532/1150131

51083155921

615042/1055821

71034050721

815542/1945521

9158

4945421

020152/1840321

125352/1745021

22065745911

325852/1640811

42016640711

EXCEPTION: Where a function can be

performed in a substantially equivalent

manner by using an alternate control,

only one of the controls needed to per-

form that function is required to comply

with this section. If the controls are iden-

tified by tactile markings, such markings

shall be provided on both controls.

4.34.4 Controls. Controls for user

activation shall comply with 4.27.4.

4.34.5 Equipment for Persons with

Vision Impairments. Instructions and

all information for use shall be made ac-

cessible to and independently usable

by persons with vision impairments.

(20) Where automated teller ma-

chines (ATMs) are provided, each ATM

shall comply with the requirements of

4.34 except where two or more are pro-

vided at a location, then only one must

comply.

EXCEPTION: Drive-up-only automated

teller machines are not required to com-

ply with 4.27.2, 4.27.3 and 4.34.3.

4.2.4* Clear Floor or Ground

Space for Wheelchairs.

4.2.4.1 Size and Approach. The mini-

mum clear floor or ground space re-

quired to accommodate a single, sta-

tionary wheelchair and occupant is 30

inches by 48 inches (760 mm by 1220

mm) (see Fig. 4a). The minimum clear

floor or ground space for wheelchairs

may be positioned for forward or paral-

lel approach to an object (see Fig. 4b

and 4c). Clear floor or ground space for

wheelchairs may be part of the knee

space required under some objects.

(4) Bins. Where bins are provided for

envelopes, waste paper, or other pur-

poses, at least one of each type pro-

vided shall comply with the applicable

reach ranges in paragraph (1), (2), or (3)

of this section.

17

4.2.4.2 Relationship of Maneuvering

Clearance to Wheelchair Spaces. One

full unobstructed side of the clear floor

or ground space for a wheelchair shall

adjoin or overlap an accessible route or

adjoin another wheelchair clear floor

space. If a clear floor space is located in

an alcove or otherwise confined on all

or part of three sides, additional maneu-

vering clearances shall be provided as

shown in Fig. 4(d) and 4(e).

4.2.4.3 Surfaces for Wheelchair

Spaces. Clear floor or ground spaces

for wheelchairs shall comply with 4.5.

4.2.5* Forward Reach. If the clear

floor space only allows forward ap-

proach to an object, the maximum high

forward reach allowed shall be 48 inches

(1220 mm) (see Fig. 5(a)). The minimum

low forward reach is 15 inches (380 mm).

If the high forward reach is over an ob-

struction, reach and clearances shall be

as shown in Fig. 5(b).

4.2.6* Side Reach. If the clear floor

space allows parallel approach by a per-

son in a wheelchair, the maximum high

side reach allowed shall be 54 inches

(1370 mm) and the low side reach shall

be no less than 9 inches (230 mm) above

the floor (Fig. 6(a) and 6(b)). If the side

reach is over an obstruction, the reach

and clearances shall be as shown in Fig

6(c).

Figure 4a. Clear floor space.

Figure 4b. Forward approach.

Figure 4c. Parallel approach.

ATM INSTALLATION FOR A CCESSIBILITY

18

FT5000 - SITE PREPARATION AND INSTALLATION GUIDE

For a front approach, where the depth

of the alcove is equal to or less than 24

inches (610 mm), the required clear floor

space is 30 inches by 48 inches (760 mm

by 1220 mm).

For a side approach, where the depth of

the alcove is equal to or less than 15

inches (380 mm), the required clear floor

space is 30 inches by 48 inches (760 mm

by 1220 mm).

Figures 4d. Clear Floor Space in

Alcoves.

For a front approach, if the depth of the

alcove is greater than 24 inches (610 mm),

then in addition to the 30-inch (760 mm)

width, a maneuvering clearance of 6

inches (150 mm) in width is required.

For a side approach, where the depth of

the alcove is greater than 15 inches (380

mm), then in addition to the 48-inch (1220

mm) length, an additional maneuvering

clearance of 12 inches (350 mm) is

required.

Figures 4e. Clear Floor Space in

Alcove.

19

Figure 6a. Parallel approach - side

reach.

Figure 6b. Parallel approach - high/

low side reach.

Figure 5a. Forward reach, unobstructed.

Figure 5b. Forward reach, obstructed.

ATM INSTALLATION FOR A CCESSIBILITY

20

Figure 6c. Side reach, obstructed.

Figure 7. ADA access dimensions for through-

the-wall ATM.

Ground exterior

Floor Interior

Rear Service Panel

aerAsseccApacidnaHedistuO

"84

)mm9121(

-ssorcA-

"03

)mm267(

-peeD-

*

derusaeM

foretnecmorf

lenaPlortnoC

*aicsaF

FT5000 - SITE PREPARATION AND INSTALLATION GUIDE

Page is loading ...

Triton Systems FT5000 Xscale Series Owner's manual

Triton Systems FT5000 Xscale Series Owner's manual

Related papers

Other documents