ADTRAN MX408 Job Aid

Brand: ADTRAN

Model: MX408

Category: Gateways/controllers

Type: Job Aid

jobAid

DESCRIPTION

TheMX408ePseudowireGateway(MX408e)providesthe

requisiteinterfacesandswitchingbetweena10/100Ethernetor

GigEnetworkporttofourclient10/100Ethernetportsandeight

DSX‐1orE1TDMports.TheDSX‐1/E1portsarealleightDSX‐1

portsoralleightE1portsandcannotbe

mixedamongtheeight

ports.TheMX408eprovidespseudowireconnectionsbetweenthe

networkandclientDSX‐1/E1portsandEthernetswitching

betweenthenetworkandclient10/100Ethernetports.

NetworkportsconsistofanRJ‐4510/100Ethernetjackanda

SmallForm‐factorPluggable(SFP)cageforaGigESFP

module.

Thefourclient10/100EthernetportsareequippedwithRJ‐45

jacks.TheeightDSX‐1orE1portsareRJ‐48Cjackssupporting

4‐wireDSX‐1sorE1s(TransmitTip,TransmitRing,ReceiveTip,

andReceiveRing).

TheMX408efrontpanel(refertothefigureabove)alsoprovides

a

moduleslotforfutureapplications.Intheeventthatamoduleis

notdeployedintheMX408e,ablankpanel(P/N1189699G1)is

installed.

Features

TheMX408ehasthefollowingfeatures:

 GigEcopper/fiberSFPor10/100EthernetNetworkports

 Fourclient10/100Ethernetports

 EightclientDSX‐1orE1short‐haul,intrabuildingports

 DB‐9craftport(RS‐232)

 FrontpanelLEDs

 Moduleslotforfutureapplications

 Dual–48VDC(±24VDC)powerinputs

 18rearpanelwire‐wrappostsforAlarmRelaysandAux

Inputs

SFPS

CAUTION

Duetocompliancecertificationrequirements,useonlySFPs

approvedbyADTRANwiththeMX408e.ADTRANcannot

certifysystemintegritywithotherSFPs . Toensureco mpatibility,

refertothedocumentationprovidedwitheachSFP.

MX408e

Pseudowire Gateway

TheMX408eisnotfactory‐equippedwithSFPs.Recommended

SFPsarelistedinthefollowingtable.

ADTRAN P/N Description

1184561P1 1000Base‐LX,1310nm,singlemode,2fiberoperation,

10kmmaximumopticaldistance

1184561PG1 1000Base‐LX,1310nm,singlemode,2fiberoperation,

10kmmaximumopticaldistance

1184561P3 1000Base‐SX,850nm,multi‐mode,2fiberoperation,

500metermaximumopticaldistanceusing50μm

multi‐modefiber,300metermaximum

opticaldista nce

using62.5μmulti‐modefiber

1184561PG3 1000Base‐SX,850nm,multi‐mode,2fiberoperation,

500metermaximumopticaldistanceusing50μm

multi‐modefiber,300metermaximumopticaldista nce

using62.5μmulti‐modefiber

1184561P4 1000Base‐T,copper,4‐wire,100meteroverCAT5UTP

cable

1184562P5 1000Base‐ZX,1550nm,

singlemode,2fiberoperation,

80kmmaximumopticaldistance

1184562PG5 1000Base‐ZX,1550nm,singlemode,2fiberoperation,

80kmmaximumopticaldistance

1442110G1 1000Base‐LX,1490nmtransmitter,1310nmreceiver,

singlefiberoperation,10kmmaximumopticaldis‐

tance

1442110G2 1000Base‐LX,1310nmtransmitter,1490nmreceiver,

singlefiberoperation,

10kmmaximumopticaldis‐

tance

1442120G1 1000Base‐LX,1490nmtransmitter,1310nmreciever,

singlefiberoperation,20kmmaximumopticaldis‐

tance

1442120G2 1000Base‐LX,1310nmtransmitter,1490nmreciever,

singlefiberoperation,20kmmaximumopticaldis‐

tance

1442140G1 1000Base‐LX,1490nmtransmitter,1310nmreciever,

singlefiberoperation,40

kmmaximumopticaldis‐

tance

1442140G2 1000Base‐LX,1310nmtransmitter,1490nmreciever,

singlefiberoperation,40kmmaximumopticaldis‐

tance

1442320G1 1000Base‐LX,1310nm,singlemode,2fiberoperation,

20kmmaximumopticaldistance

1442340G1 1000Base‐LX,1310nm,singlemode,2fiberoperation,

40kmmaximumopticaldistance

CLEI: COM7V00E_ _

Product P/N: 1189608G1

Issue Date: August 2015

Document P/N: 61189608G1-22D

ACT ALM

ACO

MODULE

1234 56781234

CRAFT

10/100

MODULE

DSX-1/E1

MX408e

1189608G1

10/100

NETWORK

2 61189608G1-22D

6. ConnecttheCRIT(critical),MAJOR,andMINORalarmleads

fromthefuseandalarmpaneltotheCommon(C),Normally

Open(NO),andNormallyClosed(NC)wire‐wrapterminals

ontheMX408erearpanelasrequired.

7. Connecttheauxiliaryinputs,labeled

AUX INPUTS,as

required.TheMX408eauxiliaryinputsconnectasfollows:

 AUXINPUTterminals1and2connecttoAlarm1

 AUXINPUTterminals3and4connecttoAlarm2

 AUXINPUTterminals5and6connecttoAlarm3

 AUXINPUTterminals7and8connecttoAlarm4

 AUXINPUTterminal9isnotconnected

FRONT PANEL LEDS

Label Status Description

NETWORK

(GE & 10/100)





Off

Green

Yellow

Nolink

Linkisup

TransmitorReceiveactivity

10/100

(Clients 1 - 4)





Off

Green

Yellow

Nolink

Linkisup

TransmitorReceiveactivity

DSX-1/E1

(1 - 8)





Off

Green

Yellow

Flashing

Yellow

Red

FlashingRed

FlashingRed

(1second)

Portisdisabled

Portisenabledandinnormal

operation

Locallyoriginatedtestinprogress

Remotelyoriginatedtestinprog‐

ress

Non‐criticalDSX‐1/E1defectin

progress(forexample,AIS,RAI)

CriticalDSX‐1/E1defect

(non‐criticalsystemdefect;for

example,

LOS,LOF)

Singlecodeviolationorburstof

codeviolationsjustoccurred

ACT



/



/



Green

Green/Yellow

(alternating)

Yellow

Red/Yellow

(alternating)

Red

FlashingRed

Normaloperation

Normaloperationandconsole

open

Softwareupdateinprogress

Self‐testfailedandconsoleopen

Self‐testfailed

Cardhasfailed

ALM



Green

Yellow

Flashing

Yellow

Red

FlashingRed

Nocritical,major,orminoralarms

Activeacknowledgednon‐critical

alarm

Activeacknowledgedcritical

alarm

Majororminoralarminprogress

Criticalalarminprogress

MODULE





Off

Green

Red

FlashingRed

Modulenotinstalled

Modulenormaloperation

Modulealarm

Modulefailed

INSTALLATION

Afterunpackingtheunit,inspectitfordamage.Ifdamageis

noted,fileaclaimwiththecarrierandthencontactADTRAN.For

moreinformation,refertothewarranty.

Followthestepslistedbelowtowallmountorrackmount

theMX408e.

1. AttachmountingbracketstothesideoftheMX408einthe

correctorientation

foreitherrackmountorwallmountusing

thetwoscrewsprovidedforeachbracket.

WARNING

Donotupsetthestabilityoftheequipmentrackafterinstallation

iscomplete.

2. SecuretheMX408etotherackorwall.

 ForRackmount:SecuretheMX408etotheequipment

rackwiththeappropriatescrews.

 ForWallmount:Preparethemountingsurfaceby

attachingaboard(typicallyplywood,3/4”to1”thick)to

awallstudusingappropriatelagbolts.Securethe

MX408etotheplywoodusingtwo3/32”to1/8”wood

screwsatleast1”inlength.

3. Connecttheframegroundfromtheframegroundlug

onthe

upperrightrearpaneloftheMX408etotheequipmentrack

groundingscreworotherappropriategrounding

connection.

4. MakepowerconnectionstotheMX408e.

NOTE

Areadilyaccessibledisconnectde vice,suchasarackmount

fuseandalarmpanel thatissuitablyapprovedandrated,

shouldbeincorporatedintothefixedwiring.

Con necttoareliablygrounded–48VDCor±24VDCsource

whichiselectricallyisolatedfromtheACsource.

Thebranchcircuitovercurrentprot ectio nshouldbea2amp,

slow‐blowfuseorcircuitbreaker.

a. Determinewhichfusepairsaretosupplypowertothe

MX408e.

b. RemovethefusesfromtheAandBslotsforthepair.

c. Connect

RETA,PWR A,RETB,andPWRB tothepow e r

connector.

PWR referstorespective–48VDCor±24VDC

powersources,while

RET referstorespectivereturns.

5. Checkvoltagesandapplypower.

a. Usingavoltmeter,verifythattheoperatingvoltageis

withinthespecificationsforAorBpowerfeeds.For

moreinformation,refertotheSpecifications.

WARNING

Installingfusesinthefuseandalarmpanelatthisstageprovides

powertotheMX408epinsandconnectorsontherearpaneland

insidetheMX408e.Exercisecautiontoavoidelectricalshock.

b. Installappropriatefuses(2amp,slow‐blow)intheslots

inthefuseandalarmpanelthatservicestheMX408e.

61189608G1-22D 3

FRONT PANEL PUSHBUTTON

CONNECT AND LOGIN TO SYSTEM

ConnecttothefrontpanelRS‐232,DB‐9connectorlabeledCRAFT

tologonandprovisiontheMX408ebywayofVT100terminalor

VT100terminalemulationsoftwaresuchasHyperTerminalor

ProCommPlus.

CRAFTportdefaultsareasfollows:

 DataRate:Auto(upto115.2kbps)

 AsynchronousDataFormat:8‐databits,noparity,1‐stopbit,

andnoflowcontrol

Press

ENTERtoactivatetheCLI.

TheMX408ecanalsobeaccessedviaTelnetthroughanEthernet

interface.

10/100port(Ethernet)defaultsareasfollows:

 IPAddress:192.168.100.1

 SubnetMask:255.255.0.0

 DefaultGateway:192.168.1.1

NOTE

Thedefault usernameandpassword are “A D M I N ” and

“PASSWORD”inallcapitalletters.

MAINTENANCE

TheMX408edoesnotrequireroutinehardwaremaintenancefor

normaloperation.ADTRANdoesnotrecommendthatrepairsbe

attemptedinthefield.Repairservicesmaybeobtainedby

returningthedefectiveunittoADTRAN.Refertothewarranty

forfurtherinformation.Fieldsupportforsoftwareisprovided

throughupgradefacilities.

Label Description

ACO

ThefrontpanelACO(AlarmCutOff)switchdisablesthe

alarmindications.

SPECIFICATIONS

SpecificationsfortheMX408eareasfollows:

 Electrical

 MaximumInputCurrent:

 1amp@24VDC

 500mA@48VDC

 OperatingVoltageRange:

 –48VDCsystems:–42VDCto–56.7VDC

 ±24VDCsystems:±20VDCto±27VDC

 MaximumHeatDissipation:24watts

 Physical

 Height:1.75inches

 Width:17.25inches

 Depth:8.5inches

 Weight:5lbs,7oz

 Environmental

 OperatingTemperatureRange:–40°Cto+65°C

 StorageTemperatureRange:–40°Cto+85°C

 RelativeHumidity:95%noncondensing

SAFETY AND REGULATORY COMPLIANCE

RefertotheMX408ePseudowireGatewaySafetyandRegulatory

ComplianceNotice(P/N61189608G1‐17)fordetailedsafetyand

regulatoryinformation.

Warranty: ADTRAN will replace or repair this product within the warranty period if it does not

meet its published specifications or fails while in service. Warranty information can be

found online at www.adtran.com/warranty

ADTRAN CUSTOMER CARE:

From within the U.S. 1.800.726.8663

From outside the U.S. +1 256.963.8716

PRICING AND AVAILABILITY 1.800.827.0807

*61189608G1-22D*

C A U T I O N C A U T I O N !

SUBJECT TO ELECTROSTATIC DAMAGE

OR DECREASE IN RELIABILITY.

HANDLING PRECAUTIONS REQUIRED.

ADTRAN MX408 Job Aid

Brand: ADTRAN

Model: MX408

Category: Gateways/controllers

Type: Job Aid

Download PDF

report

ADTRAN MX408 Job Aid

ADTRAN MX408 Job Aid

Related papers

Other documents