Alcatel-Lucent Service Aggregation Router 7705 Installation guide

Alcatel-Lucent 7705

SERVICE AGGREGATION ROUTER | RELEASE 6.0.R1

ETHERNET/GIGABIT ETHERNET ADAPTER CARD INSTALLATION GUIDE

Alcatel-Lucent Proprietary

This document contains proprietary information of Alcatel-Lucent and is not to be

disclosed or used except in accordance with applicable agreements.

Alcatel-Lucent assumes no responsibility for the accuracy of the information presented, which is subject to change

without notice.

Alcatel, Lucent, Alcatel-Lucent and the Alcatel-Lucent logo are trademarks of Alcatel-Lucent. All other trademarks

are the property of their respective owners.

Disclaimers

Alcatel-Lucent products are intended for commercial uses. Without the appropriate network design engineering,

they must not be sold, licensed or otherwise distributed for use in any hazardous environments requiring fail-safe

performance, such as in the operation of nuclear facilities, aircraft navigation or communication systems, air traffic

control, direct life-support machines, or weapons systems, in which the failure of products could lead directly to

death, personal injury, or severe physical or environmental damage. The customer hereby agrees that the use, sale,

license or other distribution of the products for any such application without the prior written consent of Alcatel-

Lucent, shall be at the customer's sole risk. The customer hereby agrees to defend and hold Alcatel-Lucent harmless

from any claims for loss, cost, damage, expense or liability that may arise out of or in connection with the use, sale,

license or other distribution of the products in such applications.

This document may contain information regarding the use and installation of non-Alcatel-Lucent products. Please

note that this information is provided as a courtesy to assist you. While Alcatel-Lucent tries to ensure that this

information accurately reflects information provided by the supplier, please refer to the materials provided with any

non-Alcatel-Lucent product and contact the supplier for confirmation. Alcatel-Lucent assumes no responsibility or

liability for incorrect or incomplete information provided about non-Alcatel-Lucent products.

However, this does not constitute a representation or warranty. The warranties provided for Alcatel-Lucent products,

if any, are set forth in contractual documentation entered into by Alcatel-Lucent and its customers.

This document was originally written in English. If there is any conflict or inconsistency between the English

version and any other version of a document, the English version shall prevail.

7705 SAR Ethernet/Gigabit Ethernet Adapter Card Installation Guide 3

Table of Contents

Preface..................................................................................................................................................... 9

About This Guide..................................................................................................................................................9

List of Technical Publications ..........................................................................................................................9

Warnings and Notes ...........................................................................................................................................10

Audience.............................................................................................................................................................11

Information Symbols...........................................................................................................................................11

Technical Support...............................................................................................................................................12

Overview................................................................................................................................................ 13

In This Chapter ...................................................................................................................................................13

Overview of the 8-port Ethernet Adapter Card and 8-port Gigabit Ethernet Adapter Card ................................14

8-port Ethernet Adapter Card Versions .........................................................................................................14

8-port Gigabit Ethernet Adapter Card Versions.............................................................................................15

Installing Adapter Cards ...................................................................................................................... 17

In This Chapter ...................................................................................................................................................17

Power Consumption ...........................................................................................................................................18

Provisioning Requirements.................................................................................................................................19

Provisioning an Adapter Card.............................................................................................................................20

Configuration Example ..................................................................................................................................21

Removing an Adapter Card Configuration..........................................................................................................23

Installation Procedures .......................................................................................................................................24

Warnings and Notes......................................................................................................................................24

Installing or Replacing an Adapter Card........................................................................................................25

Installing or Replacing an Adapter Card on the 7705 SAR-8 ...................................................................27

Installing or Replacing an Adapter Card on the 7705 SAR-18 .................................................................30

SFPs....................................................................................................................................................... 35

In This Chapter ...................................................................................................................................................35

Installing and Removing SFPs ...........................................................................................................................36

Warnings and Notes .....................................................................................................................................36

Fiber Cable Preparation ................................................................................................................................37

Locking Mechanisms.....................................................................................................................................37

SFP Support..................................................................................................................................................38

Bidirectional SFPs....................................................................................................................................46

T3/E3 SFP................................................................................................................................................46

Installing SFPs ..............................................................................................................................................47

Removing and Replacing SFPs ....................................................................................................................47

Connector and LED Descriptions ....................................................................................................... 49

In This Chapter ...................................................................................................................................................49

8-port Ethernet Adapter Card Connectors and LEDs .........................................................................................50

8-port Gigabit Ethernet Adapter Card Connectors and LEDs.............................................................................53

Table of Contents

4 7705 SAR Ethernet/Gigabit Ethernet Adapter Card Installation Guide

7705 SAR Ethernet/Gigabit Ethernet Adapter Card Installation Guide 5

List of Tables

Preface..................................................................................................................................................... 9

Table 1 Information Symbols ....................................................................................................................11

Installing Adapter Cards ...................................................................................................................... 17

Table 2 Power Consumption for 8-port Ethernet Adapter Cards ...............................................................18

Table 3 Power Consumption for 8-port Gigabit Ethernet Adapter Card .....................................................18

Table 4 8-port Ethernet Adapter Card Installation and Removal Features ................................................28

SFPs....................................................................................................................................................... 35

Table 5 SFPs for the 8-port Ethernet Adapter Card and 8-port Gigabit Ethernet Adapter Card ................38

Table 6 T3/E3 Configured Settings ............................................................................................................47

Connector and LED Descriptions ....................................................................................................... 49

Table 7 8-port Ethernet Adapter Card Features ........................................................................................50

Table 8 RJ-45 Port Pinouts—RJ-45 Female ..............................................................................................52

Table 9 8-port Gigabit Ethernet Adapter Card Features ............................................................................53

List of Tables

6 7705 SAR Ethernet/Gigabit Ethernet Adapter Card Installation Guide

7705 SAR Ethernet/Gigabit Ethernet Adapter Card Installation Guide 7

List of Figures

Installing Adapter Cards ...................................................................................................................... 17

Figure 1 7705 SAR-8 CSM and Adapter Card Slot Identification.................................................................26

Figure 2 7705 SAR-18 CSM and Adapter Card Slot Identification...............................................................26

Figure 3 Removing an 8-port Ethernet Adapter Card from the 7705 SAR-8................................................27

Figure 4 Installing an 8-port Ethernet Adapter Card on the 7705 SAR-8.....................................................29

Figure 5 Removing an 8-port Gigabit Ethernet Adapter Card from a 7705 SAR-18 ....................................31

Figure 6 Installing an 8-port Gigabit Ethernet Adapter Card on a 7705 SAR-18 .........................................32

Connector and LED Descriptions ....................................................................................................... 49

Figure 7 8-port Ethernet Adapter Card Connectors and LEDs ....................................................................50

Figure 8 RJ-45 Connector Pin Orientation ...................................................................................................51

Figure 9 8-port Gigabit Ethernet Adapter Card Connectors and LEDs ........................................................53

List of Figures

8 7705 SAR Ethernet/Gigabit Ethernet Adapter Card Installation Guide

7705 SAR Ethernet/Gigabit Ethernet Adapter Card Installation Guide 9

Preface

About This Guide

This guide provides site preparation recommendations and step-by-step procedures to install,

remove, and replace an 8-port Ethernet Adapter card or an 8-port Gigabit Ethernet Adapter

card on the 7705 SAR-8 and 7705 SAR-18. After the hardware installation process is

completed, see List of Technical Publications for information about the boot process,

software configuration, and Command Line Interface (CLI) information to configure system

and network parameters.

List of Technical Publications

The 7705 SAR OS documentation set is composed of the following guides:

• 7705 SAR OS Basic System Configuration Guide

This guide describes basic system configurations and operations.

• 7705 SAR OS System Management Guide

This guide describes system security and access configurations as well as event

logging and accounting logs.

• 7705 SAR OS Interface Configuration Guide

This guide describes card and port provisioning.

Note: Unless otherwise stated in this guide, 7705 SAR-8 also implies 7705 SAR-8 v2.

Note: This manual may contain some content that is not currently available in this release

but will be available in later maintenance releases. Please refer to the 7705 SAR OS 6.0.Rx

Software Release Notice, part number 3HE07992000xTQZZA, for information on features

supported in each load of the Release 6.0 software.

Warnings and Notes

10 7705 SAR Ethernet/Gigabit Ethernet Adapter Card Installation Guide

• 7705 SAR OS Router Configuration Guide

This guide describes logical IP routing interfaces, IP-based filtering, and routing

policies.

• 7705 SAR OS MPLS Guide

This guide describes how to configure Multiprotocol Label Switching (MPLS),

Resource Reservation Protocol for Traffic Engineering (RSVP-TE), and Label

Distribution Protocol (LDP).

• 7705 SAR OS Services Guide

This guide describes how to configure service parameters such as service access

points (SAPs), service destination points (SDPs), customer information, and user

services.

• 7705 SAR OS Quality of Service Guide

This guide describes how to configure Quality of Service (QoS) policy management.

• 7705 SAR OS Routing Protocols Guide

This guide provides an overview of dynamic routing concepts and describes how to

configure them.

• 7705 SAR OS OAM and Diagnostics Guide

This guide provides information on Operations, Administration and Maintenance

(OAM) tools.

Warnings and Notes

Observe the warnings and notes to avoid injury or router damage during installation and

maintenance. Follow the safety procedures and guidelines when working with and near

electrical equipment. Warning statements and notes are provided in each chapter.

Preface

7705 SAR Ethernet/Gigabit Ethernet Adapter Card Installation Guide 11

Audience

This guide is intended for network installers and system administrators who are responsible

for installing, configuring, or maintaining networks. This guide assumes you are familiar with

electronic and networking technologies.

Information Symbols

Table 1 describes symbols contained in this guide.

Table 1: Information Symbols

Symbol Meaning Description

Danger This symbol warns that improper handling and installation could result in bodily

injury. An electric shock hazard could exist. Before you begin work on this

equipment, be aware of hazards involving electrical circuitry, be familiar with

networking environments, and instigate accident prevention procedures.

Warning This symbol warns that improper handling and installation could result in equipment

damage or loss of data.

Caution This symbol warns that improper handling may reduce your component or system

performance.

Note This symbol provides additional operational information.

Class 1 laser products are identified in the adapter card installation guides. Only

approved Class 1 replaceable laser transceivers should be used with this product.

CLASS 1 LASER PRODUCT

Technical Support

12 7705 SAR Ethernet/Gigabit Ethernet Adapter Card Installation Guide

Technical Support

If you purchased a service agreement for your 7705 SAR-8 or 7705 SAR-18 and related

products from a distributor or authorized reseller, contact the technical support staff for that

distributor or reseller for assistance. If you purchased an Alcatel-Lucent service agreement,

check this link for instructions to contact Support personnel:

Web: http://support.alcatel-lucent.com

7705 SAR Ethernet/Gigabit Ethernet Adapter Card Installation Guide 13

Overview

In This Chapter

This chapter provides an introduction to the 8-port Ethernet Adapter card and 8-port Gigabit

Ethernet Adapter card used in the 7705 SAR-8 and the 7705 SAR-18:

• Overview of the 8-port Ethernet Adapter Card and 8-port Gigabit Ethernet Adapter

Card

Overview of the 8-port Ethernet Adapter Card and 8-port Gigabit Ethernet Adapter Card

14 7705 SAR Ethernet/Gigabit Ethernet Adapter Card Installation Guide

Overview of the 8-port Ethernet Adapter Card and

8-port Gigabit Ethernet Adapter Card

The 8-port Ethernet Adapter card has six RJ-45 ports and two small form-factor pluggable

(SFP) ports on its faceplate. The six RJ-45 ports are 10/100 Mb/s-capable ports that support

auto-sense and auto-negotiation.The two SFP ports are for 10/100/Gigabit Ethernet SFPs

(optical or electrical) and T3 SFPs. SFPs are hot-swappable input/output devices that plug

into the adapter card ports, linking the ports to fiber-optic or copper networks. See SFPs for

a list of supported SFP modules.

The 8-port Gigabit Ethernet Adapter card is designed to complement or replace the 8-port

Ethernet Adapter card in situations where greater processing power and higher throughput

capacity are required. The 8-port Gigabit Ethernet Adapter card has eight small form-factor

pluggable (SFP) ports on its faceplate. The eight SFP ports are for 10/100/Gigabit Ethernet

optical or electrical SFPs. See SFPs for a list of supported SFP modules.

The 8-port Gigabit Ethernet Adapter card is equipped with a universal -48 VDC to +24 VDC

power supply and is capable of a 1 or 2.5 Gb/s fabric interface. On the 7705 SAR-8, the card

supports a 1 Gb/s fabric interface. On the 7705 SAR-8 v2, the card supports a 1 or 2.5 Gb/s

fabric interface. Support for 2.5-Gb/s on the 7705 SAR-8 v2 requires use of the CSMv2. On

the 7705 SAR-18, the card supports a 2.5 Gb/s fabric interface.

8-port Ethernet Adapter Card Versions

There are two versions of the 8-port Ethernet Adapter card. The CLI identifier for version 1

is a8-eth and for version 2 it is a8-ethv2. Both versions are supported on the

7705 SAR-8. On the 7705 SAR-18, only version 2 is supported. The two versions are

identical except that version 2 adds support for synchronous Ethernet as a timing source, has

more memory for storage of MPLS labels, and supports a +24 VDC variant (+24 VDC power

is not supported on the 7705 SAR-18). For more information on synchronous Ethernet, refer

to the 7705 SAR OS Basic System Configuration Guide.

Note: Unless otherwise stated in this guide, the 8-port Gigabit Ethernet Adapter card

supports the same functions as the 8-port Ethernet Adapter card.

Overview

7705 SAR Ethernet/Gigabit Ethernet Adapter Card Installation Guide 15

8-port Gigabit Ethernet Adapter Card Versions

There are two versions of the 8-port Gigabit Ethernet Adapter card. The CLI identifier for

version 1 is a8-1gb-sfp and for version 2 it is a8-1gb-v2-sfp. Both versions are

supported on the 7705 SAR-8 and the 7705 SAR-18. The two versions are identical except

that version 2 has more memory to support larger tables, such as FIBs, ACLs, and so on.

Note:

• The electrical SFP (part number 3HE00062AA) does not support synchronous Ethernet

when used with version 2 of the 8-port Ethernet Adapter card.

• Unless otherwise stated in this guide, 8-port Ethernet Adapter card means both

versions.

Note:

• Unless otherwise stated in this guide, 8-port Gigabit Ethernet Adapter card means both

versions.

• Higher limits are supported only when all the adapter cards in a particular node are

equipped with hardware for larger table support.

Overview of the 8-port Ethernet Adapter Card and 8-port Gigabit Ethernet Adapter Card

16 7705 SAR Ethernet/Gigabit Ethernet Adapter Card Installation Guide

7705 SAR Ethernet/Gigabit Ethernet Adapter Card Installation Guide 17

Installing Adapter Cards

In This Chapter

This chapter provides information about installing and removing adapter cards on the

7705 SAR-8 and 7705 SAR-18.

This chapter provides information on the following topics:

• Power Consumption

• Provisioning Requirements

• Provisioning an Adapter Card

→ Configuration Example

• Removing an Adapter Card Configuration

• Installation Procedures

→ Warnings and Notes

→ Installing or Replacing an Adapter Card

Power Consumption

18 7705 SAR Ethernet/Gigabit Ethernet Adapter Card Installation Guide

Power Consumption

Table 2 lists the power consumption for the 8-port Ethernet Adapter card.

Table 3 lists the power consumption for the 8-port Gigabit Ethernet Adapter card.

For information such as power consumption, environmental specifications, and adapter card

physical specifications for the 7705 SAR-8 or 7705 SAR-18 hardware, refer to the “System

Specifications” section in the 7705 SAR-8 Chassis Installation Guide and the 7705 SAR-18

Chassis Installation Guide.

Table 2: Power Consumption for 8-port Ethernet Adapter Cards

Description Typical Power (W) Maximum Power (W)

8-port Ethernet Adapter card

version 1

17.5 W 20 W

8-port Ethernet Adapter card

version 2

16.8 W 20 W

Table 3: Power Consumption for 8-port Gigabit Ethernet Adapter Card

Description Typical Power (W) Maximum Power (W)

8-port Gigabit Ethernet Adapter card

(version 1 and version 2)

32.5 W 38 W

Installing Adapter Cards

7705 SAR Ethernet/Gigabit Ethernet Adapter Card Installation Guide 19

Provisioning Requirements

To configure cards and ports, you must be able to access the 7705 SAR-8 or 7705 SAR-18

by console or Telnet connection. Refer to the 7705 SAR-8 Chassis Installation Guide or

7705 SAR-18 Chassis Installation Guide for information and instructions on console and

Telnet connections.

The CSM does not require provisioning. However, the IOM, which is an integral part of the

CSM software module, must be activated before any adapter cards and port parameters can

be provisioned and configured. The IOM is activated using the card and card-type CLI

commands to specify its slot number and card type. Adapter cards must be provisioned before

their ports can be configured.

Provision components in the following order:

1. Card slot number (use the card command)

2. Card type

3. Adapter card slot number (use the mda command)

4. Adapter card type

5. Ports

Note: The following provisioning requirements apply to IOMs and adapter cards:

• IOMs are specified using the card and card-type commands (items 1 and 2 in the

list below).

• Adapter cards are provisioned and configured using the mda and mda-type commands

(items 3 and 4 in the list below).

Provisioning an Adapter Card

20 7705 SAR Ethernet/Gigabit Ethernet Adapter Card Installation Guide

Provisioning an Adapter Card

After the IOM has been activated on the CSM (Steps 1 and 2 below), continue in the config

context with the following CLI commands to provision the adapter card. The steps below

describe how to provision an 8-port Ethernet Adapter card version 1 in slots MDA 1 and 2 on

a 7705 SAR-8.

The 7705 SAR-8 supports up to 6 adapter cards and the 7705 SAR-18 supports up to

12 adapter cards in any combination that does not exceed the maximum. However, for a

network application, at least one of the installed cards must be a network-capable adapter

card. Within this maximum, up to six 8-port Ethernet Adapter cards or 8-port Gigabit

Ethernet Adapter cards can be configured on a 7705 SAR-8 chassis and up twelve 8-port

Ethernet Adapter cards version 2 or 8-port Gigabit Ethernet Adapter cards can be configured

on a 7705 SAR-18 chassis.

You can now install the adapter card. See Installing or Replacing an Adapter Card. If you

need to install an additional adapter card, continue the configuration process with Step 6

before installing the card:

Note:

1. The slot-number is always 1 and the card-type is always iom-sar.

Command Syntax Example

Step 1. card slot-number

1

card 1

Step 2. card-type card-type

1

card-type iom-sar

Step 3. mda mda-number mda 1

Step 4. mda-type mda-type mda-type a8-eth

Step 5. exit exit

Step 6. mda mda-number mda 2

Step 7. mda-type mda-type mda-type a8-eth

Step 8. exit exit

Page is loading ...

Alcatel-Lucent Service Aggregation Router 7705 Installation guide

Related papers

Other documents