Southern Enterprises FA580700TX User manual

1

SOUTHERN ENTERPRISES INC.

This product has been engineered for easy installation and is

constructed for durability. Please take the time to read through

and follow these assembly instructions.

YOU CAN INSTALL THIS ITEM.

WALL MOUNT FIREPLACE

FA580700TX

Suggested tools: Flat head screw driver, power drill, ¼” drill bit, 24” level, and a tape measure.

HARDWARE LIST

(1) FIREPLACE ASSEMBLY

1 PC

(2) FUEL CANISTER

HOLDER

3 PCS

(3)CANDLE HOLDER

1PC

(4)PLASTIC WALL ANCHOR

3PCS

(5) PAN HEAD SCREWS

3PCS

2

INSTALLATION INSTRUCTIONS

Please count, identify and compare parts to the hardware and parts list on the preceding page to be sure all parts are

present. You will also need a flat head screw driver, drill, ¼” drill bit, tape measure, and a 24” level. If any items are

missing, please contact our parts/ service department at 800-633-5096 or in Dallas 972-869-0111 from 9 AM to 4 PM

CDT Monday - Friday. Missing or damaged hardware and/ or parts will be replaced free of charge. WE DO NOT

SELL PARTS. WE DO NOT RECOMMEND MODIFYING PRODUCT (S) AND WE ARE NOT REPONSIBLE

FOR ANY DAMAGES DUE TO PRODUCT MODIFICATION (S).

DANGER

The fireplace will have open flames and will generate heat.

• Make sure to keep all combustible items away from the fireplace when the gel fuel is burning.

• DO NOT touch the fireplace when the gel fuel is burning.

• DO NOT mount the fireplace on a wall that is covered with wood paneling or wallpaper.

1. Locate the fireplace on a solid wall and at a comfortable height off the floor, normally eye level.

2. Measure the wall and mark the fireplace width and height. See Figure 1.

Figure 1 – Installation Measurements

25

-3/4

"

Eye Level

27"

3

3. Measure the wall and mark the location of the center of each of the three screw mounting holes. See Figure 2.

Using the level, make sure that all three marks are level on the wall.

Figure 2 – Screw Hole Location

4. Using the power drill and ¼” drill bit, drill three ¼” holes through the wallboard at the mounting hole marks.

NOTICE

Make sure not to drill into electrical wiring or plumbing pipes.

5. Insert one of the furnished plastic anchors into each of the three ¼” holes. See Figure 3. Make sure that the wall

anchor is flush with the wall.

NOTE – It may be necessary to use a small hammer to gently tap the anchor into place.

6. Using the flat head screwdriver, install one Pan Head Screw into each of the anchors. See Figure 3. Turn the screw

in until there is a gap of 5/8” between the head of the screw and the wall surface.

Figure 3 – Wall Anchor Installation

7. Install the fireplace (1, Figure 4) onto the three mounting screws using the mounting holes (2, Figure 4). The

5/8”

24-

3/4"

6-3/8"

7-1/8"

14-1/4"

Drill three 1/4" holes

into wall

23-5

/8"

4

proper and secure mounting of the fireplace is when the top edge of each of the mounting holes is resting securely

on the mounting screw (3, Figure 4).

NOTICE

Using the level, check to make sure that the fireplace is horizontally level and vertically plumb (straight up and

down).

2

3

1

Figure 4 – Install Fireplace

8. Remove the three fuel canister holders (2, Figure 5) from the fireplace and install one gel fuel canister (1, Figure 5)

into each of the holders.

5

NOTICE

• Make sure to remove the gel fuel canisters paper label (4, Figure 5)

before installing the canister into the holder.

• Shake the gel fuel canister before installing it into the canister holder.

Figure 5 –Fuel Canister Holder and Gel Fuel Canister

9. Install the gel fuel holders into the fireplace into the appropriate mounting hole (3, Figure 5) in the fireplace.

10. Following the instructions on the gel fuel canister, remove the lid (2, Figure 6) from the gel fuel canister (1, Figure

6), and using a long match, light the fuel in each of the canisters.

Figure 6 – Fuel Canister Installed

6

DANGER

• PROLONGED USE OF THE GEL FUEL IN THE FIREPLACE WILL CAUSE THE

FIREPLACE TO BECOME HOT AND POTENTIALLY CAN CAUSE BURNS IF TOUCHED.

• DO NOT BURN MORE THAN THREE CANISTERS OF FUEL AT ONE TIME.

• BEFORE LIGHTING THE FUEL, MAKE SURE THAT THE PAPER LABEL IS REMOVED

FROM EACH OF THE GEL FUEL CANISTERS.

• USE LONG MATCHES TO LIGHT EACH CANISTER OF FUEL.

• DO NOT TOUCH THE CANISTERS WITH BARE HANDS UNTIL THE FLAME HAS BEEN

EXTINGUISHED FOR 20 MINUTES.

• DO NOT BURN ANYTHING EXCEPT THE SPECIFIED CANISTERS OF GEL FUEL IN

THE FIREBOX.

• KEEP CHILDREN AWAY FROM THE FIREPLACE WHEN IN USE.

• KEEP FLAMABLE OBJECTS, SUCH AS CURTAINS OR DRAPERYS, AWAY FROM THE

FIREPLACE WHEN THE GEL FUEL HAS BEEN IGNITED.

●

MAKE SURE THE CUSTOMER DOES NOT PLACE ANY DECORATIVE ITEMS ON TOP

OF THE UNIT AT ANYTIME.

● DO NOT TOUCH THE UPPER PART OF THE UNIT WHILE IT IS STILL IN OPERATION

OR LIE.

● THE CANDLE HOLD HOLDER ACTS AS A COVER TO PUT OUT FIRE IF ONE WISHS

TO STOP THE FLAME.

7

Please count, identify and compare the unit’s parts against the hardware list shown on the first page of this

manual to be sure that all parts are present. Extra hardware may be included. If any items are missing, please

contact our parts/ service department at (800) 633-5096 9am-4pm Monday-Friday Central Time. Missing or

damaged hardware and/ or parts will be replaced free of charge. WE DO NOT SELL PARTS.WE DO NOT

RECOMMEND MODIFYING PRODUCT (S) AND WE ARE NOT RESPONSIBLE FOR ANY

DAMAGES DUE TO PRODUCT MODIFICATION (S).

"

PARTS REPLACEMENT FORM

Please count, identify and compare parts and hardware to the illustrated parts list that is included in this manual to be sure all

parts are present. It may help to separate the parts and label them to correspond with the part list. Extra hardware may be

included. If any items are missing, please contact our parts/service department at (800) 633-5096 or in Dallas (972) 869-0111/

9am – 4pm Mon-Fri Central time. Missing or damaged hardware and/ or parts will be replaced free of charge. WE DO NOT

SELL PARTS. WE DO NOT RECOMMEND MODIFYING PRODUCT(S) AND WE ARE NOT RESPONSIBLE FOR

ANY DAMAGES DUE TO PRODUCT MODIFICATION(S). If this product has been purchased from our retail affiliates

more than 9 months ago, we are under no obligation to provide parts or replacement merchandise. Parts will not be available

for items arriving fully assembled.

FA580700TX

Customer Name

PARTS

LETTER

PART

DESCRIPTION

QUANTITY

NEEDED

Street, City, State, Zip

Phone#

Please indicate where you purchased this item.

Store/website/catalog

/ /

SOUTHERN ENTERPRISES INC.

P.O. Box 59996 Dallas, Texas 75229

Please indicate color/size/style number

/ /

Southern Enterprises FA580700TX User manual

This manual is also suitable for

Southern Enterprises FA580700TX User manual

Related papers

Other documents