1
SOUTHERN ENTERPRISES INC.
This product has been engineered for easy installation and is
constructed for durability. Please take the time to read through
and follow these assembly instructions.
YOU CAN INSTALL THIS ITEM.
WALL MOUNT FIREPLACE
FA580700TX
Suggested tools: Flat head screw driver, power drill, ¼” drill bit, 24” level, and a tape measure.
HARDWARE LIST
(1) FIREPLACE ASSEMBLY
1 PC
(2) FUEL CANISTER
HOLDER
3 PCS
(3)CANDLE HOLDER
1PC
(4)PLASTIC WALL ANCHOR
3PCS
(5) PAN HEAD SCREWS
3PCS
2
INSTALLATION INSTRUCTIONS
Please count, identify and compare parts to the hardware and parts list on the preceding page to be sure all parts are
present. You will also need a flat head screw driver, drill, ¼” drill bit, tape measure, and a 24” level. If any items are
missing, please contact our parts/ service department at 800-633-5096 or in Dallas 972-869-0111 from 9 AM to 4 PM
CDT Monday - Friday. Missing or damaged hardware and/ or parts will be replaced free of charge. WE DO NOT
SELL PARTS. WE DO NOT RECOMMEND MODIFYING PRODUCT (S) AND WE ARE NOT REPONSIBLE
FOR ANY DAMAGES DUE TO PRODUCT MODIFICATION (S).
DANGER
The fireplace will have open flames and will generate heat.
• Make sure to keep all combustible items away from the fireplace when the gel fuel is burning.
• DO NOT touch the fireplace when the gel fuel is burning.
• DO NOT mount the fireplace on a wall that is covered with wood paneling or wallpaper.
1. Locate the fireplace on a solid wall and at a comfortable height off the floor, normally eye level.
2. Measure the wall and mark the fireplace width and height. See Figure 1.
Figure 1 – Installation Measurements
25
-3/4
"
Eye Level
27"
3
3. Measure the wall and mark the location of the center of each of the three screw mounting holes. See Figure 2.
Using the level, make sure that all three marks are level on the wall.
Figure 2 – Screw Hole Location
4. Using the power drill and ¼” drill bit, drill three ¼” holes through the wallboard at the mounting hole marks.
NOTICE
Make sure not to drill into electrical wiring or plumbing pipes.
5. Insert one of the furnished plastic anchors into each of the three ¼” holes. See Figure 3. Make sure that the wall
anchor is flush with the wall.
NOTE – It may be necessary to use a small hammer to gently tap the anchor into place.
6. Using the flat head screwdriver, install one Pan Head Screw into each of the anchors. See Figure 3. Turn the screw
in until there is a gap of 5/8” between the head of the screw and the wall surface.
Figure 3 – Wall Anchor Installation
7. Install the fireplace (1, Figure 4) onto the three mounting screws using the mounting holes (2, Figure 4). The
5/8”
24-
3/4"
6-3/8"
7-1/8"
14-1/4"
Drill three 1/4" holes
into wall
23-5
/8"
4
proper and secure mounting of the fireplace is when the top edge of each of the mounting holes is resting securely
on the mounting screw (3, Figure 4).
NOTICE
Using the level, check to make sure that the fireplace is horizontally level and vertically plumb (straight up and
down).
2
3
1
Figure 4 – Install Fireplace
8. Remove the three fuel canister holders (2, Figure 5) from the fireplace and install one gel fuel canister (1, Figure 5)
into each of the holders.
5
NOTICE
• Make sure to remove the gel fuel canisters paper label (4, Figure 5)
before installing the canister into the holder.
• Shake the gel fuel canister before installing it into the canister holder.
Figure 5 –Fuel Canister Holder and Gel Fuel Canister
9. Install the gel fuel holders into the fireplace into the appropriate mounting hole (3, Figure 5) in the fireplace.
10. Following the instructions on the gel fuel canister, remove the lid (2, Figure 6) from the gel fuel canister (1, Figure
6), and using a long match, light the fuel in each of the canisters.
Figure 6 – Fuel Canister Installed
6
DANGER
• PROLONGED USE OF THE GEL FUEL IN THE FIREPLACE WILL CAUSE THE
FIREPLACE TO BECOME HOT AND POTENTIALLY CAN CAUSE BURNS IF TOUCHED.
• DO NOT BURN MORE THAN THREE CANISTERS OF FUEL AT ONE TIME.
• BEFORE LIGHTING THE FUEL, MAKE SURE THAT THE PAPER LABEL IS REMOVED
FROM EACH OF THE GEL FUEL CANISTERS.
• USE LONG MATCHES TO LIGHT EACH CANISTER OF FUEL.
• DO NOT TOUCH THE CANISTERS WITH BARE HANDS UNTIL THE FLAME HAS BEEN
EXTINGUISHED FOR 20 MINUTES.
• DO NOT BURN ANYTHING EXCEPT THE SPECIFIED CANISTERS OF GEL FUEL IN
THE FIREBOX.
• KEEP CHILDREN AWAY FROM THE FIREPLACE WHEN IN USE.
• KEEP FLAMABLE OBJECTS, SUCH AS CURTAINS OR DRAPERYS, AWAY FROM THE
FIREPLACE WHEN THE GEL FUEL HAS BEEN IGNITED.
●
MAKE SURE THE CUSTOMER DOES NOT PLACE ANY DECORATIVE ITEMS ON TOP
OF THE UNIT AT ANYTIME.
● DO NOT TOUCH THE UPPER PART OF THE UNIT WHILE IT IS STILL IN OPERATION
OR LIE.
● THE CANDLE HOLD HOLDER ACTS AS A COVER TO PUT OUT FIRE IF ONE WISHS
TO STOP THE FLAME.
7
Please count, identify and compare the unit’s parts against the hardware list shown on the first page of this
manual to be sure that all parts are present. Extra hardware may be included. If any items are missing, please
contact our parts/ service department at (800) 633-5096 9am-4pm Monday-Friday Central Time. Missing or
damaged hardware and/ or parts will be replaced free of charge. WE DO NOT SELL PARTS.WE DO NOT
RECOMMEND MODIFYING PRODUCT (S) AND WE ARE NOT RESPONSIBLE FOR ANY
DAMAGES DUE TO PRODUCT MODIFICATION (S).
"
PARTS REPLACEMENT FORM
Please count, identify and compare parts and hardware to the illustrated parts list that is included in this manual to be sure all
parts are present. It may help to separate the parts and label them to correspond with the part list. Extra hardware may be
included. If any items are missing, please contact our parts/service department at (800) 633-5096 or in Dallas (972) 869-0111/
9am – 4pm Mon-Fri Central time. Missing or damaged hardware and/ or parts will be replaced free of charge. WE DO NOT
SELL PARTS. WE DO NOT RECOMMEND MODIFYING PRODUCT(S) AND WE ARE NOT RESPONSIBLE FOR
ANY DAMAGES DUE TO PRODUCT MODIFICATION(S). If this product has been purchased from our retail affiliates
more than 9 months ago, we are under no obligation to provide parts or replacement merchandise. Parts will not be available
for items arriving fully assembled.
FA580700TX
Customer Name
PARTS
LETTER
PART
DESCRIPTION
QUANTITY
NEEDED
Street, City, State, Zip
Phone#
Please indicate where you purchased this item.
Store/website/catalog
/ /
SOUTHERN ENTERPRISES INC.
P.O. Box 59996 Dallas, Texas 75229
Please indicate color/size/style number
/ /
/
