2. Crystorama
  3. 295-DB

Crystorama 295-DB User manual

  • Hello! I've reviewed the assembly instructions for the Crystorama Light 295-DB. This document provides a step-by-step guide on how to install and assemble the light fixture, including how to adjust the hanging height, connect wiring, and install the shades and diffuser. It also explains how to replace bulbs. I'm here to assist you with any questions you might have about this product.
  • What type of bulbs are required?
    Is this fixture suitable for damp locations?
    How can I replace the bulb?
ASSEMBLYINSTRUCTIONMODEL#295-DB
CRYST
RAMA
WARNING:
ElectricalDanger TurnPoweroff
WARNING: ThisproductcanexposeyoutoLead
whichisknowntothestateofCaliforniatocausecancer
and/orbirthdefectsorreproductiveharm.Formore
informationgotowww.P65Warnings.ca.gov
L I G H T I N GT H EW A YF O RS I X T YY E A R S
installedbyalicensedelectrician
inaccordancewiththeNational
Allelectricalcomponentsmustbe
ElectricCodeandtheappropriate
localelectricalcodes.
Youwillneed3-MediumBaseBulb
60WattsRecommended100WattsMax.
USELEDBULBSFOREXTENDEDUSE
Howtoinstall
Crystorama.com
This fixture is Dry rated
3.Determinethepreferredhangingheightandadjust
therequiredrods.
5.Slipcanopykitalongwireandthreaditintothetop
oftherodassembly.
7.Installthebulb(notincluded)intothesocket.
4.Feedthewiresthroughtherodsandconnectthem
together.
1.Separatethemountingplatefromthecanopykitby
removingthescrews.
2.Installthemountingplatetotheoutletboxusing
twooutletboxscrews.
6.Installcanopyontothemountingplate,andsecure
withthemountingscrews.
NIPPLE
TOPCOUPLING
BOTTOM
COUPLING
HEXNUT
SOCKET
GLASSDIFFUSER
PLASTICWASHER
BOTTOMFINIAL
ROD
CYLINDERNUT
TOPSHADE
BOTTOMSHADE
METALRING
(IFREPLACEDFROMTHEBOTTOM,YOUNEEDTOREMOVE
THEBOTTOMFINIALANDDIFFUSERTOREPLACETHEBULB.)
FROMTHETOPOPENINGOFSHADE,REPLACEPREVIOUS
BULBW/NEWBULB.
HOWTOREPLACEBULB:
5-7/8”
7/8”
10-1/2”
18”
ROD1
ROD2
6”
12”
1Pc
3Pcs
ROD2=
ROD1=
TOPSHADE
BOTTOMSHADE
17-3/4”
17-3/4”
5”
5”
52-3/4”
17-1/4”
GLASSDIFFUSER
8.Threadthenippleontothecouplingandadjust
thelengthofnippletofitwiththeglass.Tighten
itwithhexnut.
9.Slidetheglassdiffuserandtheplasticwasherover
thenipple,thensecurewiththebottomfinial.
CRYST
RAMA
L I G H T I N GT H EW A YF O RS I X T YY E A R S
PartNumber
PartNumbers
A.(1)-Mountinghardware
B.(1)-Mountingplate
G.(1)-TopshadeW17-3/4’’xH5’’ #XRF295DBSHA17.75IN
F.(3)-RodD5/8’’xL12’’ #XRF290DBROD12IN
C.(2)-mountingscrew
E.(1)-RodD5/8’’xL6’’ #XRF290DBROD6IN
ASSEMBLYINSTRUCTIONMODEL#295-DB
I.(1)-BottomshadeW17-3/4’’xH5’’ #XRF295DBBOTSHA17.75IN
Crystorama.com
D.(1)-CanopykitW5-7/8’’xH7/8’’ #XRF290DBCAN5.875IN
H.(6)-Cylindernut
A
B
CD
E
F
G
H
I
JK
L
M
N
O
K.(1)-Hexnut
O.(1)-Bottomfinial#XRF293DBFIN
M.(1)-Glassdiffuser#XRF295DIF17.25IN
L.(1)-Nipple
N.(1)-Plasticwasher
J.(1)-Metalring
/