Xerox Printer FS 5250 IPC User manual

WARNING:

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used

in accordance with the instruction manual, may cause interference to radio communications. It has

been tested and found to comply with the limits for a Class A computing device pursuant to Subpart

B of Part 15 of FCC Rules, which are designed to provide reasonable protection against such inter-

ference when operated in a commercial environment. Operation of this equipment in a residential

area is likely to cause interference in which case the user at his own expense will be required to take

whatever measures may be required to correct the interference.

EMC directive:

This product observes the rules and regulations of the EMC directive. If so required, a declaration of

conformity in local language stipulating the applied rules and regulations can be obtained.

Trademarks:

Company and product names mentioned in this datasheet are trademarks or registered trademarks of

their respective owners.

Xerox Electronic Documentation

Xerox FS 5250 /

Xerox FS 5250 IPC

User’s Guide

Doc. no. D60262 Revision 01

Solution for Xerox Printers

- 2 -

SAFETY NOTICE

Caution

Do not attempt to disable any safety features designed

for this equipment.

If this equipment is connected to an outlet that has been

incorrectly connected to the building wiring, serious

electric shock could be the result.

To protect yourself against electric shock, follow these instructions.

1. Connect the machine only to an outlet with the correct voltage. The correct voltage

appears from the information plate of the equipment.

2. Make sure that the equipment is turned off, before you connect or disconnect the power

cord or other cables.

3. Do not use the equipment in an area, where it can become wet.

4. Refer service or repairs to qualified personnel.

5. There may be increased risks of electric shock and personal injury in connection with

disassembling and servicing of this equipment. Professional service personnel should

understand this and take necessary precautions.

6. The safety features of some parts may not always be obvious. Therefore, spare parts

must have the identical or equivalent characteristics of the original parts.

7. The maintenance information for this equipment has been written for professional

service staff and is not intended for use by others.

8. Make sure that the power outlet is properly grounded.

Table of Contents

Xerox FS 5250, User’s Guide

- 3 -

Table of Contents

1. Introduction to the Xerox FS 5250.............................................................6

1.1. What is the Xerox FS 5250? ............................................................6

1.2. Printer Driver Selection ....................................................................6

2. Items Supplied.............................................................................................8

3. Product Features.........................................................................................9

4. Supported Control Units.............................................................................10

5. Installation Requirements...........................................................................11

5.1. Pre-Installation Requirements .........................................................11

5.1.1 National Language .............................................................. 11

5.1.2 EU or US Settings ............................................................... 12

5.2. Working Environment ......................................................................12

6. Connections and Installation of the Xerox FS 5250.................................13

6.1. The Rear Panel................................................................................13

Changing the Driver: ....................................................................15

6.2. Emulation.........................................................................................15

6.2.1 Via the Line .........................................................................15

6.2.2 Via the Address Switch .......................................................16

6.2.3 Address Setting...................................................................18

6.2.4 Dual Printer Emulation ........................................................18

6.3. Upgrading to IPDS ...........................................................................20

6.4. Connecting the Xerox FS 5250 to the Printer ..................................21

6.4.1 Connecting via Centronics output .......................................21

6.5. Connecting the Xerox FS 5250 to the System.................................22

6.5.1 TEST Function ....................................................................23

6.5.2 Timeout ...............................................................................24

7. Operation of the Xerox FS 5250.................................................................25

7.1. Top Panel of the Xerox FS 5250 ......................................................25

7.1.1 CU.......................................................................................25

7.1.2 PAR (Parallel input) ............................................................25

7.1.3 SER (Serial input/output) ....................................................26

7.1.4 READY (Printer Ready) ......................................................26

8. Function Selection via the Line..................................................................27

8.1. Syntax of an FSL Function............................................................... 27

8.2. The Escape Character .....................................................................28

8.3. Defining a Temporary Escape Character .........................................29

8.4. Removing Temporary Escape Character .........................................29

8.5. Defining a Permanent Escape Character ........................................30

8.6. Removing Permanent Escape Character.........................................30

8.7. Commands for Storing and Restoring Settings ................................ 32

8.8. Pass-Through Mode ........................................................................33

8.8.1 Pass-through mode - XES...................................................34

8.9. Transparency Mode Limitations .......................................................35

9. idaSetup - IPDS Programming....................................................................36

10. Programming the Xerox FS 5250 - Non-IPDS..........................................37

11. Selected FSL Functions............................................................................38

Introduction

Xerox FS 5250, User’s Guide

- 4 -

11.1. Paper Size .....................................................................................38

11.1.1 Trays .................................................................................38

11.1.2 Changing paper size .........................................................38

11.1.3 Saving the command.........................................................40

11.1.4 Changing paper size example ...........................................40

11.1.5 Other commands............................................................... 40

11.2. Paper Trays ...................................................................................41

11.2.1 Basic printer set-up ...........................................................41

11.2.2 Changing paper trays ........................................................41

11.2.3 Other commands............................................................... 42

11.3. Page Format ..................................................................................42

11.3.1 Formats.............................................................................42

11.3.2 Changing Page Format .....................................................43

Saving the command....................................................................43

11.3.3 Changing page format example ........................................44

11.3.4 Other commands............................................................... 44

11.4. Automatic Page Orientation ...........................................................45

11.4.1 Automatic Page Orientation Chart ....................................46

Explanation to the chart on Automatic Page

Orientation.........................................................................47

11.5. Fonts.............................................................................................. 48

11.5.1 Selecting Fonts - PCL..................................................48

What to consider ............................................................... 48

Changing font ....................................................................49

11.5.2 Default GFID Table ........................................................... 50

11.5.3 Scaleable Fonts ................................................................ 52

11.5.4 Defining Fonts - PCL ...................................................53

What you need to know .....................................................54

Font definition example .....................................................58

Other commands............................................................... 58

11.5.5 Selecting Fonts - XES..................................................58

What to consider ............................................................... 58

Changing font ....................................................................59

Changing font example......................................................59

Other commands............................................................... 59

11.5.6 Defining Fonts - XES...................................................60

What you need to know .....................................................60

Font definition....................................................................60

CPI / GFID Relation........................................................... 64

COR CPI / GFID Relation..................................................64

11.6. Optional Scaling ............................................................................64

Font definition example .....................................................65

Other commands............................................................... 65

11.7. Duplex Printing ..............................................................................66

11.7.1 System or interface? .........................................................66

11.7.2 What to consider ............................................................... 66

11.7.3 Binding option ...................................................................67

11.7.4 Selecting duplex printing ...................................................68

11.7.5 Orientation ........................................................................68

Introduction

Xerox FS 5250, User’s Guide

- 5 -

Duplex selection example, PCL.........................................69

Duplex selection example, XES ........................................69

11.8. Output Data ...................................................................................70

11.9. Port Share Option ..........................................................................72

11.9.1 Sending the commands from the system ..........................74

11.9.2 Sending the commands from the PC.................................75

Printer sharing example ....................................................75

12. Programming via Shareport......................................................................76

12.1. Activating the Y249 Engineering Function .....................................76

12.2. Deactivating the Y249 Engineering Function ................................ 77

12.3. Limitations when Y249 is active .....................................................77

12.4. Updating firmware..........................................................................77

13. PC Support Virtual Printer........................................................................78

14. Error Messages..........................................................................................79

14.1. Recoverable Errors ........................................................................79

14.2. Non-Recoverable Hardware Errors................................................81

Appendix A: Supported Setup Functions......................................................82

XES Mode............................................................................................... 82

PCL Mode............................................................................................... 84

Quick Reference Guide to the Supported FSL Functions .......................86

Appendix B: Test Printout..............................................................................100

Appendix C: Use of Xerox FS 5250 Serial Port (Out)...................................102

Appendix D: Related Manuals........................................................................103

Index.................................................................................................................104

Introduction

Xerox FS 5250, User’s Guide

- 6 -

1. Introduction to the Xerox FS 5250

This manual applies to the Xerox FS 5250 protocol converter. The Xerox FS

5250 supports twinax Centronics and RS232 inputs. The default output is

Centronics.

NOTE:

Both products: “Xerox FS 5250” and “Xerox FS 5250 IPC” will be

referred to as “Xerox FS 5250” unless specific reference is made to

the IPDS functionality of the Xerox FS 5250 IPC.

The manual describes how the Xerox FS 5250 is connected and operated.

We recommended that you read it before you start using the protocol

converter. Keep the manual in a safe place for future referen ce.

It is assumed that the reader has a basic knowledge and under standing of

IBM computer systems, especially the IBM 5250 Information Display System.

It is also assumed that the reader has adequate knowledge of the printer

which is going to be connected to the Xerox FS 5250 .

The Xerox FS 5250 can be used with most Xerox decentralised printers .

1.1. What is the Xerox FS 5250?

The Xerox FS 5250 is a protocol converter which enables most Low End or

Midrange Xerox printers (or other output device) to be connected to an IBM

computer system. See Supported Control Units for information on the IBM

systems to which the Xerox FS 5250 connects.

The printer or device should have a Centronics parallel connector in order to

be connected to the Xerox FS 5250 protocol converter.

1.2. Printer Driver Selection

With the Xerox FS 5250, you have the option of selecting between 2 printer

drivers: XES and PCL on the rear panel B, A, T -address switch.

Introduction

Xerox FS 5250, User’s Guide

- 7 -

NOTE:

PCL = factory default. "A" position

Note

Operation mode is outside the B, A, T position. If

you wish to operate in PCL mode, do not change

the default position of the switch!

XES

1

) = "B" position.

Note

To change the driver from default PCL to FSL,

you must follow the instructions in the section

“Changing the Printer Driver”

If you wish to change to the FSL driver, the printer driver must be selected

before you start the operation of the Xerox FS 5250 box. See the section on

“Changing the Printer Driver”.

For details as to the selecting of other output data types in XES mode, you

are referred to the chapter "Output Data".

1

The XES mode selection handles XDPM and XPPM data streams.

Items Supplied...

Xerox FS 5250, User’s Guide

- 8 -

2. Items Supplied...

Please check that your Xerox FS 5250 kit is complete. The complete

contents of the kit consists of the following items:

• Xerox FS 5250 box

• Wall plug power supply

• Parallel printer cable

• Auto-terminating twinax T-cable

• Xerox FS 5250 /Xerox FS 5250 IPC, User's Guide,

Document no. D60262 (electronic format)

• Xerox FS 5250 /Xerox FS 5250 IPC, Quick Guide,

Document no. D10262 (hardcopy format)

In addition the following accessories can be used:

• Printer cable, Centronics (Order no. 999023 030)

• Serial input cable (Order no. 999010 030)

• Serial output cable has to be ordered for the specific printer you are

going to connect to. Please contact your i-data dealer for more details.

(See also Appendix A)

• Printer sharing cable, Centronics (Order no. 999022-030)

IPC Upgrade Kit

• IPC option (for upgrade) (Order no. 293011-001)

Product Features

Xerox FS 5250, User’s Guide

- 9 -

3. Product Features

Non-IPC

• Support of 5224, 5225, 5256, 4234 printer emulations as alternatives to

3812/5219/3816

• Twinax setup via share port or twinax port

• Flash prom allowing downloading of new firmware via the twinax o r the

Centronics port

• Support of ida PSS

• Automatic input sharing between Twinax, Centronics and RS 232 input

ports

• Support of duplex printing

• Support of bar code printing

• Support of Automatic Page Orientation

If equipped with the optional IPC module:

• Support of IPDS printer emulation

• Support of additional non-IPDS emulation

Supported Control Units

Xerox FS 5250, User’s Guide

- 10 -

4. Supported Control Units

The Xerox FS 5250 will connect to the following control units :

• IBM /34

• IBM /36, all models

• IBM /38, all models

• IBM AS/400

• IBM 5294 and 5394 remote controllers

Installation Requirements

Xerox FS 5250, User’s Guide

- 11 -

5. Installation Requirements

This chapter gives a short description of the requirements for the installation

of the Xerox FS 5250.

When you have made certain that all the components have been included

and you have carried out the pre-installation tasks (see below) according to

your needs and requirements, you are ready for operation.

5.1. Pre-Installation Requirements

Prior to installation and connection you must first make sure that you have:

1. Set the desired national language - do this via the line (using function Y8).

2. Checked the paper size (EU / US) settings.

NOTE:

From the factory, the controller will come with the correct language

settings. Therefore, you will normally not have to alter any original

settings.

5.1.1 National Language

Via the Line

National language can be set via the line in function Y8.

To change the language in Y8, you will have to send the command below to

the Xerox FS 5250. You can do this either in a file you transmit to the printer

or by entering the command on your screen and make a local copy (print

screen).

%Y8,<number of new language>%

In function Y8 you can select the following languages:

Option Description

37 English (US) EBCDIC

256 International

273 Austrian/German

274 Belgian

Installation Requirements

Xerox FS 5250, User’s Guide

- 12 -

275 Brazilian

276 Canadian French

277 Danish/Norwegian

278 Finnish/Swedish

280 Italian

281 Japanese (English)

282 Portuguese

283 Spanish Speaking

284 Spanish

285 English (UK)

297 French

500 Multinational

871 Iceland

NOTE: Factory default depends on your initial order.

5.1.2 EU or US Settings

When you receive the Xerox FS 5250, the interface is already in the box and

is ready to connect to the system and to the printer. From the factory, the

Xerox FS 5250 is set up for either US (Letter) or European (A4) paper size

depending on what you specified when ordering the Xerox FS 5250.

5.2. Working Environment

The Xerox FS 5250 protocol converter can be installed in the following

environment:

• Temperature range from 10° - 40°

• Humidity between 8-80 %, non-condensing

• Power consumption: 120 and 220 Volt version - max. 21.5 VA

Connections and Installation

Xerox FS 5250, User’s Guide

- 13 -

6. Connections and Installation of

the Xerox FS 5250

This chapter starts with an overview of the functionality of the rear panel.

Then follows a description of how you connect the Xerox FS 5250 box to a

printer and finally how to connect it to a System.

NOTE:

Before you start the installation, make sure that you set the address

switch and the desired emulation. See the description in the section

"Emulation".

6.1. The Rear Panel

RS232

12-18 VDC.

0.7A

PARALLEL IN PARALLEL OUTADDR

+ --

B

A

T

6

5

4

3

2

0

1

A = PCL, B = XES

Xerox FS 5250 Rear Panel

PARALLEL OUT

The parallel output port can be connected to the parallel/Centronics in put

port on the target printer (parallel out cable is supplied with the kit).

PARALLEL IN

The parallel input port can be connected to the parallel/Centronics out put on

a PC or similar source which enables it to share the printer with the host. For

this connection you need a cable ending in a 25-pole D-Sub connector

(order no. 999022 030).

SERIAL IN/OUT

The serial port can be configured either as input or as output. Default

configuration is input.

Connections and Installation

Xerox FS 5250, User’s Guide

- 14 -

The serial input port is connected to the serial output on a PC or similar

source able to share the printer with the host.

For this connection you need a cable ending in a 25-pole RS connector

(order no. 999010 030).

To use the serial input, Function 24, " Data Input/Output Port Select "

must be set to zero (Centronics out, which is factory default).

You must also make the following settings on your PC to match the default

settings on the box:

Function Y15: Baud rate, set to 5 = 9600

Function Y16: Number of data bits, set to 8 = 8 bits

Function Y17: Parity, set to 1 = No Parity

Function Y18: Number of Stop Bits, set to 1 = 1 Stop Bit

If this is not possible, you must change the functions 15, 16, 17 and 18 on

the box to match the PC's values.

NOTE:

Programming of functions 15, 16, 17, 18 and 24 is not possible via the

serial port. These functions have to be programmed either via the

twinax or via the parallel input port.

TWINAX CONNECTOR

Before the twinax cable is connected, be sure to turn the box power OFF.

When power is turned off, plug the automatically terminating twinax T-cable

(twin BNC cable) into the socket on the rear panel and turn the connector

ring clockwise to lock.

ADDRESS SWITCH: EMULATION & PRINTER DRIVER SELECT

You use the address switch for:

• selecting/changing emulation, setting the address and for the generating

of test printouts. Tests can also be made via the line. See the section

TEST function for details. For details on emulation see the section

"Emulation".

• selecting/changing of printer driver. You have the option of selecting

between XES and PCL.

Y24 = 0 is also

used for

Centronics

output.

Connections and Installation

Xerox FS 5250, User’s Guide

- 15 -

If you wish to operate in default PCL mode, the box is ready to operate when

delivered. It is important that you do not change the position of the address switch.

Note that operation mode is outside of the B, A & T positions.

If you wish to select XES, you must follow the instructions in the below section

“Changing the Driver”.

Changing the Driver:

To change from PCL to XES driver, the rotary switch has to be in position T at

power on. Current printer driver is indicated on printout. Now turn the rotary

switch to position B (XES). New position is then indicated as “alternate printer

driver” (XES) on second printout. When correct position is obtained, turn rotary

switch away from B, A or T positions (any other position will do). Power the

converter OFF and ON again. The new driver is now active. (If you wish to

reinstall the PCL driver later on, repeat the above, setting the switch into the A

(PCL) position instead of the B (XES) position).

6.2. Emulation

If you wish to see the current emulation, you can generate a test print out by

turning the address switch to the T-position.

In Xerox FS 5250 you can select emulation in two ways. Either via the

address switch (see below) or you can do it via the line by activating FSL

function Y37 (only in PCL mode).

The following emulations are supported by the Xerox FS 5250:

IBM 3812 / 5219 / 3816

IBM 5224

IBM 5225

IBM 5256

IBM 4234

IBM 4245/6262

As default the Xerox FS 5250 will emulate IBM 3812/5219/3816.

As default the Xerox FS 5250 IPC will emulate IPDS

6.2.1 Via the Line

Selecting emulation via the line can be done in PCL only!

You can set the desired emulation in FSL function Y37.

Note that if you select emulation via function 37, you must physically write

the emulation. See the chart in the following for details.

Connections and Installation

Xerox FS 5250, User’s Guide

- 16 -

E.g. %Y37,5224%

will select emulation 5224

An option for dual printer emulation is also available for the Xerox FS 5250

when equipped with an IPDS upgrade module. See below for a description of

dual printer emulation.

This chart provides information on the emulations which can be selected in

the n1 parameter of function Y37.

In the column "Write" is stated what you physically have to write in this

parameter.

Non-IPDS IPDS

Y37,n1 Y37,n1

Write Emulation Write Emulation

3812 *3812/5219/

3816

3812 *3812/5219/

3816

5224 5224 5224 5224

5225 5225 5225 5225

5256 5256 5256 5256

4234 4234 4234 4234

4245 4245/6262 *IPDS *IPDS

4245 4245/6262

* default value

SCS printers

6.2.2 Via the Address Switch

Emulation selected on the address switch is described in the following.

The T-cable must be disconnected at the converter before changing

emulation.

Select emulation on the address switch as follows:

1. Switch off the box

2. Turn the address switch to the "T" position.

3. Switch on power to the box.

Connections and Installation

Xerox FS 5250, User’s Guide

- 17 -

4. When the Xerox FS 5250 is ready, it will eject a page with the follo wing

message:

"Current emulation is xxxx"

5. Set the desired emulation by turning the address switch to the position

defined in the chart in the following:

Non-IPDS IPDS

Selection Emulation Selection Emulation

*0 3812/5219/3816 0 3812/5219/3816

1 5224 1 5224

2 5225 2 5225

3 5256 3 5256

4 4234 4 4234

5 3812/5219/3816 *5 IPDS

6 4245/6262 6 4245/6262

* default value

SCS printers

6. A new message stating the current emulation will be printed after a few

seconds. Then power off the Xerox FS 5250.

7. Power on the Xerox FS 5250.

8. Turn to the "T" position again and check that the emulation has been

changed. (See the settings printout). See TEST Function.

9. Turn the switch back to the correct device address (consult your

system administrator if necessary).

10. Connect the twinax cable and power on the Xerox FS 5250 or follow

the procedure for setting the address via the switch. See the following

section.

Check whether the configuration complies with the requirements of your

installation and print jobs.

NOTE: Make sure that you have set the address switch before you switch

power on.

Connections and Installation

Xerox FS 5250, User’s Guide

- 18 -

6.2.3 Address Setting

via the address switch

To select the desired address using the rotary address switch follow these

steps. The steps 1 through 4 are mandatory, whereas the steps 4 through 6

are optional.

1. Power off the Xerox FS 5250.

2. Disconnect the T-cable

3. Set the address switch to the desired address. The options are 0-6.

4. Power on the Xerox FS 5250. The desired address will be set at this

point of time.

5. To verify the address turn the switch to the “T” position to print the

current settings printout.

6. Turn the switch back to the desired address number.

The default configuration of the Xerox FS 5250 can be used for most

application programs and uses. You should only change the address

and the emulation if necessary. Change only the rest of the settings if

you have special requirements.

6.2.4 Dual Printer Emulation

PCL only

With IPDS support in the Xerox FS 5250, you have the option of configuring

a second emulation on a different address.

You select a second emulation via the line in function Y37 and both

parameters (n1 and n2) in Y37 must be specified.

The parameter n1 sets the printer emulation. Note that you will have to

physically write the IBM printer number of the desired emulation. For IPDS,

you must write: *IPDS. Parameter n2 specifies the device address.

Connections and Installation

Xerox FS 5250, User’s Guide

- 19 -

NOTE:

The device address (n2) must be different from the address switch

setting or this command will only modify the primary printer emulation

without creating a secondary.

One non-IPDS and one IPDS emulation can be defined.

The secondary printer device will be deleted if you attempt to configure two

similar devices (e.g. two non-IPDS devices) or if Y37 is used without

specifying n2.

For this change to become effective, you must turn power to the converter off

for approx. 10 seconds and then back on.

Non-IPDS as primary emulation

If the primary printer emulation (set via the address switch) is set to non-

IPDS, you can set the second emulation via the twinax port activating Y37.

E.g.

Primary emulation: non-IPDS (set via address switch)

Second emulation: %Y37,*IPDS,6%%X1

You have now a non-IPDS primary emulation, and a second IPDS emulation

answering on device address 6.

As an alternative setup, you can also use the Centronics port activating

function Y249, Enter Engineering Mode.

E.g.:

Primary emulation: non-IPDS (set via address switch)

Second emulation: %Y249, password%

2)

%Y37,*IPDS,5%%X1

IPDS as primary emulation

If the primary emulation is set to IPDS (set via the address switch) the only

way to set a second emulation is through the Centronics port enabling

function Y249, Enter Engineering Mode. You must still set function Y37 to

the desired emulation.

E.g.

Primary emulation: IPDS (set via address switch)

Second emulation: %Y249,password%

%Y37,3812,1%%X1

2

As the password is sensitive information, please contact point of purchase for details

Connections and Installation

Xerox FS 5250, User’s Guide

- 20 -

With IPDS as primary emulation, you have now selected 3812 as second

emulation to answer on address 1.

NOTE:

If you wish to define 2 emulations, you are recommended to set the

primary emulation to non-IPDS.

6.3. Upgrading to IPDS

If you need to upgrade your Xerox FS 5250 with the IPC module, please follow

these instruction before proceeding with the installation.

1. Unscrew the 4 screws from the bottom of the converter.

2. Place you hands on each side of the box, bottom facing down and the rear

panel facing you. Carefully press open the top cover of the converter.

3. Place the IPC module (main component side facing up) on the PCB of the

box. Note that the connector has to be placed on top of the PCB’s

connector (to the right on the PCB).

4. Make sure the plastic supports fit in the holes of the IPC module.

5. Press the module gently into position and, while still facing the rear panel,

place the top cover precisely above the bottom cover so that all edges are

aligned. Press the top cover gently into a locked position.

6. Re-insert the screws and fasten.

7. Now proceed to the actual installation of the converter to the printer and

the system.

Page is loading ...

Xerox Printer FS 5250 IPC User manual

This manual is also suitable for

Xerox Printer FS 5250 IPC User manual

Related papers

Other documents