Star Micronics TUP992-24J1 User manual

Product Specifications Manual

TUP900 Series

Rev. 0.01

Star Micronics Co., Ltd.

Special Products Operating Division

Rev 0.01

TUP900 Series Specifications Manual

i

--- CONTENTS ---

1. GENERAL DESCRIPTION ...................................................................................................................1-1

2. PRINTER CONFIGURATION...............................................................................................................2-1

2-1 Basic Configuration...............................................................................................................................2-1

2-1-1 Thermal Mechanism Module ......................................................................................................2-1

2-1-2 Presenter Module .......................................................................................................................2-1

2-1-3 Control Board Module ................................................................................................................2-1

2-1-4 Power Connector Cable Module ................................................................................................2-1

2-1-5 Paper Roll Supply Module..........................................................................................................2-1

2-2 Selectable Options for Each Module ....................................................................................................2-1

3. BASIC SPECIFICATIONS ....................................................................................................................3-1

3-1 Printing Specifications ..........................................................................................................................3-1

3-2 Character Specifications and Bar Code Specifications ........................................................................3-2

3-2-1 STAR Line Mode ........................................................................................................................3-2

3-2-2 STAR Page Mode ......................................................................................................................3-3

3-3 Paper Specifications .............................................................................................................................3-4

3-3-1 Thermal Paper roll......................................................................................................................3-4

3-3-2 Black Mark Specifications ..........................................................................................................3-7

3-4 Thermal Mechanism Module ................................................................................................................3-9

3-4-1 Thermal Head.............................................................................................................................3-9

3-4-2 Auto-cutter..................................................................................................................................3-9

3-4-3 Paper Feed Motor ......................................................................................................................3-9

3-4-4 Sensors ......................................................................................................................................3-9

3-5 Presenter Module ...............................................................................................................................3-10

3-5-1 Feed Rollers .............................................................................................................................3-10

3-5-2 Paper Feed Motor ....................................................................................................................3-10

3-5-3 Sensors ....................................................................................................................................3-10

3-6 Paper Roll Supply Module ..................................................................................................................3-11

3-6-1 Paper Roll Holder .....................................................................................................................3-11

3-6-2 Near-end Sensor ......................................................................................................................3-11

3-7 Reliability Specifications .....................................................................................................................3-12

3-7-1 Thermal Mechanism Module ....................................................................................................3-12

3-7-2 Thermal Head...........................................................................................................................3-12

3-7-3 Auto-cutter................................................................................................................................3-12

3-7-4 Presenter Module .....................................................................................................................3-12

4. EXTERNAL SPECIFICATIONS............................................................................................................4-1

4-1 External Specifications .........................................................................................................................4-1

4-1-1 External Dimensions ..................................................................................................................4-1

4-1-2 External Drawings ......................................................................................................................4-1

4-1-3 Mass...........................................................................................................................................4-1

4-2 Operation Panel Specifications.............................................................................................................4-1

4-2-1 Switches.....................................................................................................................................4-1

4-2-2 LED ............................................................................................................................................4-1

4-3 Interface................................................................................................................................................4-1

4-4 DIP Switches ........................................................................................................................................4-1

5. ENVIRONMENT SPECIFICATIONS ....................................................................................................5-1

5-1 Temperature and Humidity ...................................................................................................................5-1

5-1-1 When Operating .........................................................................................................................5-1

5-1-2 When Stored (Excluding Paper roll) ...........................................................................................5-1

Rev 0.01

TUP900 Series Specifications Manual

ii

5-2 Static Electricity Tolerance (ESD).........................................................................................................5-2

5-3 AC Line Noise Tolerance......................................................................................................................5-2

5-4 Vibrations, Falling Shocks ....................................................................................................................5-2

5-4-1 Vibration Test (When Packaged) ...............................................................................................5-2

5-4-2 Drop Test (When Packaged)......................................................................................................5-2

5-5 Dust ......................................................................................................................................................5-2

6. SAFETY................................................................................................................................................6-1

6-1 Standard ...............................................................................................................................................6-1

7. USAGE EXAMPLE (LAYOUT EXAMPLE) ...........................................................................................7-1

7-1 Control Board Layout............................................................................................................................7-1

7-1-1 Control Board Layout 2 ..............................................................................................................7-1

7-1-2 Control Board Layout 3 ..............................................................................................................7-1

7-2 High Volume Paper Roll Supply (RHU-T900, Optional Part)................................................................7-1

7-2-1 Horizontal Layout .......................................................................................................................7-1

7-2-2 Vertical Layout............................................................................................................................7-1

8. SETTING UP THE PRINTER UNIT......................................................................................................8-1

8-1 Mounting the Units................................................................................................................................8-1

8-1-1 Mounting the Printer Unit............................................................................................................8-1

8-1-2 Mounting the High Volume Paper Roll Supply (RHU-T900).......................................................8-1

8-1-3 Mounting the Printer Unit and the High Volume Paper Roll Supply (RHU-T900).......................8-1

8-2 Mounting the High Volume Paper Roll Supply (RHU-T900) .................................................................8-1

8-3 Adjusting the Paper roll Holder Unit......................................................................................................8-2

8-3-1 Handling 111.5 mm Paper Width ...............................................................................................8-2

8-3-2 Handling 82 mm Paper Width ....................................................................................................8-2

8-3-3 Handling 79.5 mm Paper Width .................................................................................................8-2

8-4 Mounting the Friction Spring.................................................................................................................8-4

8-4-1 Using the Spring Base................................................................................................................8-4

8-4-2 When Not Using the Spring Base...............................................................................................8-4

8-5 Adjusting the Near End Sensor ............................................................................................................8-8

8-5-1 Adjusting to the Paper roll Width ................................................................................................8-8

8-5-2 Adjusting to the Paper roll Diameter Direction ...........................................................................8-8

9. HANDLING THE PRINTER UNIT.........................................................................................................9-1

9-1 Precautions Regarding Designs ...........................................................................................................9-1

9-2 Precautions for Handling ......................................................................................................................9-1

9-3 Precautions Concerning Safety ............................................................................................................9-2

9-4 How to Set the Paper roll......................................................................................................................9-3

9-5 Performing Maintenance.......................................................................................................................9-7

9-5-1 Cleaning the Thermal Head and Platen .....................................................................................9-7

9-5-2 Handling Recording Paper Jams................................................................................................9-7

9-5-3 How to Release the Cutter Lock.................................................................................................9-7

10. Control board module (TBD900 Series) .......................................................................................... 10—1

11. Power connector cable module (PBD-9) ......................................................................................... 11—2

Rev 0.01

TUP900 Series Specifications Manual

1-1

1. GENERAL DESCRIPTION

The TUP900 series is a direct line thermal printer capable of high speed printing that employs a thermal

line dot printing system and is composed of a unit comprising thermal paper roll storage. This type is used,

embedded in electronic devices such as games, ATM, and information kiosks.

Model Name Display Directions

TUP9 9 2 – 24 J1

Installed Fonts None: Standard models

J1: Japanese Characters

Power Specifications 24: 24 VDC

Mechanism Type 2: Standard

Printer Type 9: Presenter equipped with a recovery function

as standard.

TUP900 Series Thermal Unit Printer

Rev 0.01

TUP900 Series Specifications Manual

2-1

2. PRINTER CONFIGURATION

2-1 Basic Configuration

This unit is composed of modules. The configuration is shown below.

TUP992-24/TUP992-24J1 (Thermal line unit printers)

Thermal mechanism module (TMP900 Series)

Presenter module (PR900 Series)

Control board module (TBD900 Series)

Power connector cable module (PBD-9)

Paper roll supply module

2-1-1 Thermal Mechanism Module

This is composed of the printer mechanism portion that prints using a thermal head while paper is being fed,

and an auto-cutter mechanism that cuts the paper by command.

2-1-2 Presenter Module

The presenter module is composed of a mechanism that discharges and that recovers paper (such as

receipts) that has been printed and cut by the thermal mechanism module.

2-1-3 Control Board Module

This is the control board that controls the thermal mechanism and the presenter.

2-1-4 Power Connector Cable Module

This is composed of the connector portion that connects the optional power adapter set to the control board,

and the power switch.

2-1-5 Paper Roll Supply Module

This supports the thermal paper roll on a shaft and functions to supply paper to the thermal mechanism

module. This is also provided a damper roller unit to alleviate the shock caused by the inertia of the paper

roll when feeding the thermal paper.

2-2 Selectable Options for Each Module

This unit is used by mounting the following selectable options on each module.

The following table shows the options for each module.

Unit/Module Name Content of Option Part Number Part Name

30781430 PS60L-24A Adapter Set JP

30781440 PS60L-24A Adapter Set US

30781450 PS60L-24A Adapter Set EU

30781460 PS60L-24A Adapter Set UK

30781470 PS60L-24A Adapter Set AS

TUP992-24

TUP992-24J1

Power Adapter

30781480 PS60L-24A Adapter Set CH

High Volume Paper Roll

Supply

39590020 RHU-T900

Near-end Sensor 39590030 NEU-T900

Damper Roller 39591000 DRU-T900

TMP900 Series

Control Panel Board Unit 39591500 OPA-T900

39607400 IFBD-HD04

39607411 IFBD-HC04

39607420 IFBD-HU04

39607430 IFBD-HN04

I/F

39607440 IFBD-HE04

TBD900 Series

Power Connector Cable 39206500 PBD-9

Rev 0.01

TUP900 Series Specifications Manual

3-1

3. BASIC SPECIFICATIONS

3-1 Printing Specifications

(1) Print Method: Direct Thermal Line Printing

(2) Dot Configuration: 832 dots/line

(3) Dot Density: 8 dots/mm (203 DPI)

(4) Printing Region: Maximum 104 mm (See figure below)

Notes 1) The mechanism can handle paper widths of 79.5 ±0.5 to 111.5 ±0.5 mm. However, it is

recommended that a print layout is set that allows plenty of print margin on the left and right

sides for the paper that is used. Also, the standard position of printing to the paper width is

center of the paper width.

Left and right margins in the printing region are recommended to be a minimum of 3.75 mm.

2) When using a paper width that is less than the maximum print width of the head (104 mm),

consider the recording paper feeding state so that the print region does not leave both edges

of the recording paper.

(5) Print Format: Maximum 69 columns (12 × 24 fonts)

Maximum 34 columns (24 × 24 Chinese character fonts)

(Only on Chinese character models)

(6) Character Space: Programmable

(7) Print Speed: 1) HS mode Maximum 150 mm/s

2) LQ mode Maximum 110 mm/s

3) HQ mode Maximum 60 mm/s

4) Two Color Printing Mode Maximum 60 mm/s

Note 1) Printing speed varies according to the processing speed of the controller and the temperature

control using the head thermistor.

(8) Paper Feed: Thermal Mechanism Module Friction Feed Method

Presenter Module Roller Friction Feed Method

(9) Paper Feed Pitch: 0.125 mm (1 step on the paper feed pulse motor)

(10) Line Width: 4 mm, 3 mm

(11) Cuttable Sheet Length: 75 to 300 mm

(12) Print Head: Line Thermal Head

(13) Presenter: With Recovery Function

(14) Emulation: Star Line Mode

Star Page Mode

111.5 ±0.5 mm (Maximum paper width)

104 mm (Maximum print region, 832 dots) 3.75 mm3.75 mm

0.125 mm

Fig. 3.1.4 Print Region

Rev 0.01

TUP900 Series Specifications Manual

3-2

3-2 Character Specifications and Bar Code Specifications

3-2-1 STAR Line Mode

Item Contents

Standard Specifications Alphanumeric Characters 95 Characters

Expanded Graphics 128 Characters

International Characters 32 Characters

Alphanumeric Characters 95 Characters

Expanded Graphics 128 Characters

JIS Level-1 Kanji Set (Note

1)

3489 Characters

JIS Level-2 Kanji Set

(Note 1)

3388 Characters

Special Symbols 83 Characters

Japanese Language

Chinese Characters

Single Byte Characters 282 Characters

Alphanumeric Characters 95 Characters

Character Type

Chinese Language

Character Specifications

Chinese Characters

(Note 2)

7189 Characters

Alphanumeric Characters 12 × 24 dots (W × H)

IBM Graphics 12 × 32 dots (W × H)

Single Byte Characters 12 × 24 dots (W × H) (When using Chinese Specifications)

Character

Configuration

Two Byte Chinese

Characters

24 × 24 dots (W × H) (When using Chinese Specifications)

12 × 24 dots Font 1.50 mm × 3.00 mm (W × H)

12 × 32 dots Font 1.50 mm × 4.00 mm (W × H)

Character

Dimensions

24 × 24 dots Font 3.00 mm × 3.00 mm (W × H)

Character Code

Table

40 Code Pages

Bar Codes UPC-A

UPC-E

JAN/EAN8

JAN/EAN13

ITF

CODE39

CODE93

CODE128

CODABAR (NW-7)

Notes 1) JIS level-1 and level-2 kanji sets conform to JISx0208-1983. They correspond to SHIFT-JIS code.

2) Conforms to GB8312

Rev 0.01

TUP900 Series Specifications Manual

3-3

3-2-2 STAR Page Mode

Item Contents

Small Characters Alphanumeric Characters

and Others

220 Characters

International Characters 32 Characters

Alphanumeric Characters

and Others

220 CharactersStandard

Characters

International Characters 32 Characters

Single Byte

Characters

Alphanumeric Characters

and Others

158 Characters

Alphanumeric Characters 95 Characters

Expanded Graphics 128 Characters

JIS Level-1 Kanji Set (Note

1)

3489 Characters

JIS Level-2 Kanji Set

(Note 1)

3388 Characters

Special Symbols 83 Characters

Japanese

Language

Chinese

Characters

Single Byte Characters 282 Characters

Alphanumeric Characters 95 Characters

Chinese Character

Chinese

Characters

Chinese Characters

(Note 2)

7189 Characters

Alphanumeric Characters

and Others

128 CharactersBold Characters

International Characters 32 Characters

Character Type

OCR Characters Alphanumeric Characters

and Others

103 Characters

Small Characters 8 × 16 dots (W × H)

Standard

Characters

16 × 24 dots (W × H)

Single Byte

Characters

12 × 24 dots (W × H) (When using Chinese Specifications)

Two Byte Chinese

Characters

24 × 24 dots (W × H) (When using Chinese Specifications)

Bold Characters 24 × 32 dots (W × H)

Character

Configuration

OCR Characters 16 × 24 dots (W × H)

8 × 16 dots Font 1.00 mm × 2.00 mm (W × H)

12 × 24 dots Font 1.50 mm × 3.00 mm (W × H)

16 × 24 dots Font 2.00 mm × 3.00 mm (W × H)

24 × 24 dots Font 3.00 mm × 3.00 mm (W × H)

Character

Dimensions

24 × 32 dots Font 3.00 mm × 4.00 mm (W × H)

Character Code

Table

2 Code Pages

Bar Codes UPC-A

UPC-E

JAN/EAN8

JAN/EAN13

ITF

CODE39

CODE93

CODE128

CODABAR (NW-7)

Notes 1) JIS level-1 and level-2 kanji sets conform to JISx0208-1983. They correspond to SHIFT-JIS code.

2) Conforms to GB8312

Rev 0.01

TUP900 Series Specifications Manual

3-4

3-3 Paper Specifications

3-3-1 Thermal Paper roll

(1) Paper Width: 79.5 ±0.5 mm to 111.5 ±0.5 mm

(Rolled Dimensions: 80 +0.5/-1 to 112 +0.5/-1 mm)

(2) Paper Thickness: 65 to 150 µm

(3) Paper roll Outer Diameter: Maximum φ150 mm

Note 1) Use of optional parts enables up to φ254 mm.

(4) Shaft Core Inner Diameter (mm)/Outer Diameter (mm):

When paper thickness is 65 to 100 µm:

Shaft core inner diameter: Min. 25.4 ±1 mm;

Shaft core outer diameter: Min. 31.4 ±1 mm

When paper thickness is 100 to 150 µm:

Shaft core inner diameter: Min. 50.8 ±1 mm;

Shaft core outer diameter: Min. 56.8 ±1 mm

Note 1) The tolerance value of the paper roll shaft core (paper tube) varies according to the

thickness of the paper that you use.

When using paper that is outside of the above specification ranges, paper jams may occur.

(5) Recommended Thermal Paper

Manufacturers

Manufacturer

Name

Quality Characteristics and Use

Paper

Thickness

(µm)

P220AG Normal Type 65

HP220A Long-storage Type 65

HP220AB-1 Long-storage Type 75

P220AB Normal Type for Cards and Tickets 85

P220AC-1 Normal Type for Cards and Tickets 95

P220AC Normal Type for Cards and Tickets 105

P220AD Normal Type for Cards and Tickets 130

P220AE-1 Normal Type for Cards and Tickets 150

PB670 2-color Type (Red/Black) 75

Mitsubishi

Paper

PB770 2-color Type (Blue/Black) 75

PD150R Normal Type 75

PD160R Long-storage Type 65/75

PD750R 2-color Type (Red/Black) 75

Oji Paper

Company

PD700R 2-color Type (Blue/Black) 75

P-320RB 2-color Type (Red/Black) 65KSP

P-320BB 2-color Type (Blue/Black) 65

Nippon Paper

Industries

TF50KS-E2C Normal Type 65

Note 1) Print density settings must be changed according to the type and thickness of the paper.

Density settings can be changed using the print density setting command <ESC> <RS> 'd'

n.

(6) Head Adjust Lever on the Thermal Mechanism Module

The TUP900 Series printers require that the head position be adjusted according to the thickness of the

paper to be used to ensure high quality printing. The head position is adjusted by changing the position

of the head adjustment lever.

See the table below to set to the optimum lever position.

• When 65 µm ≤ Paper Thickness < 100 µm: Normal Position

• When 100 µm ≤ Paper Thickness ≤ 150 µm: Position for Thick Paper

Rev 0.01

Head Adjust Lever

Fig. 3.3.1.6.A Normal Position

3-6

Fig. 3.3.1.6.B Position for Thick Paper

TUP900 Series Specifications Manual

Rev 0.01

TUP900 Series Specifications Manual

3-6

(7) Weight Shaft and Loop Guide on the Presenter Module

The TUP900 Series printers require the accessory weight shaft and loop guide for the thickness of the

paper to be used to ensure the smooth feeding of paper.

See the table below for the optimum mechanism status.

• When 65 µm ≤ Paper Thickness < 100 µm: Loop guide mounting required.

Weight shaft unnecessary

• When 100 µm ≤ Paper Thickness ≤

150 µm: Weight shaft mounting required.

Loop guide unnecessary

Note 1) Refer to the PR921-24-A product specifications manual for details regarding the mounting

position of the loop guide and the weight shaft and how to mount them.

(8) Pre-printing Range on the Backside of Recording Paper

When pre-printing to the backside of recording paper, it should meet the following specifications.

(9) Others

• Coloring Side: Roll outer side

• Trailing Edge Processing: Do not glue to fasten to paper roll and shaft core.

The trailing edge should not be folded.

Printing Direction

Min. 15 mm from Paper Edge

Paper Back Side

Pre-printing Prohibited Range

Printing Surface is Paper Back Side

25 (mm)

10 (mm)

Paper Width Center

Rev 0.01

TUP900 Series Specifications Manual

3-7

3-3-2 Black Mark Specifications

The following describes the recommended black mark specifications for printers that use the paper out

sensor as the black mark sensor.

(1) Black Mark Pitch (Dimension A)

Black mark pitch can be set to a dimension of A = 75 to 300 mm.

Note 1) Black mark pitches can be set to the above describe range, but it is recommended to use a

pitch that is at least 80 mm, in consideration of the variation in printing positions.

(2) Black Mark Dimensions

See the following drawings for the dimensions of black marks to be printed.

(3) PCS Value

The PCS value of black marks to be printed should be a minimum of 0.90.

Note 1) The PCS value of black marks can cause page skipping problems or improper page length

detection if they do not meet the aforementioned specifications.

For that reason, always ensure that the PCS value is met.

Printing Direction

Min. 15 mm

Paper Back Side

Printing Surface is Paper Back Side

Printing Range

1+1, -0.8 (mm)

2.5 ±2 (mm)

5 ±1

(mm)

A (mm)

Cutting Position

B (mm)

C (mm)

Rev 0.01

TUP900 Series Specifications Manual

3-8

(4) Top Margin (Dimension B)

Set the printing range, leaving plenty of top margin from the cutting position.

When not reversing paper feed, a top margin with a minimum total of 19 mm is recommended with the

distance of 15 mm from the thermal head heating elements to the cutting position and the empty paper

feed amount (1 line = 4 mm empty feed) considering the motor acceleration step.

If you want a smaller top margin setting, change the memory switch settings. However, in that case, it

is recommended to set the top margin of the empty paper feed amount (1 line = 4 mm empty feed)

considering the motor acceleration step.

Notes 1) If the top margin is not sufficiently taken, problems, such as the page being skipped, can occur.

So, you must set for plenty of top margin.

2) The setting of the printing range should not exceed the black mark pitch.

(5) Bottom Margin (Dimension C)

Set the printing range leaving plenty of bottom margin from the trailing edge of the printing range to the

black mark.

It is necessary to consider the printing precision of the black mark, the printing TOP accuracy (±2 mm of

the standard printing position), the setup ambient temperature of the printer, and part wear-out to set

the bottom margin. It is recommended that the following bottom margin be secured to set the printing

range.

Bottom Margin (Dimension C) ≥ 3 mm + (Dimension A × 3%)

Notes 1) If the bottom margin is not sufficiently taken, problems, such as the page being skipped, can

occur.

So, you must set for plenty of bottom margin.

2) The setting of the printing range should not exceed the black mark pitch.

(6) Example Setting of the Printing Region

The following shows a printing range setting example when not reverse feeding recording paper.

• When Black Mark Pitch (Dimension A) is 100 mm:

The top margin is set to 20 mm.

The bottom margin is set to 3 mm + (100 mm × 0.03) = 6 mm.

According to the above, it is necessary to set the printing range to less than 100 mm – 20 mm – 6

mm = 74 mm.

Note 1) If you have any questions regarding how to set the printing range for the black mark, consult

with STAR Micronics.

Rev 0.01

TUP900 Series Specifications Manual

3-9

3-4 Thermal Mechanism Module

3-4-1 Thermal Head

(1) Thermal Element Configuration: 2 elements/dot

(2) Number of Thermal Elements: 832 dots

(3) Thermal Element Scanning Density: 0.125 mm/dot (8 dots/mm)

(4) Average Resistance Value: 800 Ω ±3% (initial value)

(5) Drive Power Voltage: Head drive Vh 24 VDC ±10%

Driver IC Vdd 5 VDC ±5%

3-4-2 Auto-cutter

(1) Cutter Type: Separated, V-blade Guillotine Type

(2) Paper Cut States: Full cut

Note 1) The presenter model is standardly equipped with this type of cutter. It does not perform partial

cuts.

(3) Cut Duty: 1 Cut/within 3 seconds

Note 1) The auto-cutter life will notable shorten if it is not used within the above range.

(4) Cutter Position: The distance from the thermal head heating element positions (the printing position)

to the auto-cutter blade positions (the cutting position) is 15 ±0.5 mm.

3-4-3 Paper Feed Motor

(1) Format: 4 Phase PM Type Bipolar Stepping Motor

(2) Drive Voltage: 24 VDC ±10%

3-4-4 Sensors

(1) Head Temperature Detection: Thermistor

(2) Paper Out Detection: Reflective Type Photo-interrupter

(3) Platen Position Detection: Micro Switch

(4) Cutter Home Position Detection: Micro Switch

Note 1) A reflective photo-interrupter is used for the paper out sensor, so it can also be used as a

black mark sensor.

In such cases, some restrictions exist for black mark pitch detection.

Rev 0.01

TUP900 Series Specifications Manual

3-10

3-5 Presenter Module

3-5-1 Feed Rollers

(1) Feed Method: Friction Method

(2) Paper Feed Speed: 300 mm/s

Note 1) Paper feed speed varies according to the ambient environment and the thickness of the paper

used.

3-5-2 Paper Feed Motor

(1) Format: DC Brush Motor

(2) Drive Voltage: 24 VDC ±10%

3-5-3 Sensors

(1) Paper Sensor 1: Reflective Type Photo-interrupter

(2) Paper Sensor 2: Reflective Type Photo-interrupter

(3) Paper Sensor 3: Reflective Type Photo-interrupter

Rev 0.01

TUP900 Series Specifications Manual

3-11

3-6 Paper Roll Supply Module

3-6-1 Paper Roll Holder

(1) Paper roll Support Method: Shaft Support Method Using the Paper roll Holder (Fixed Shaft Unit)

(2) Paper Tube: Inner Diameter φ1 Inch Paper Tube (φ25.4 ±1 mm)

Inner Diameter φ2 Inch Paper Tube (φ50.8 ±1 mm)

Inner Diameter φ3 Inch Paper Tube (φ76.2 ±1 mm)

Note 1) The accessory components must be replaced to use each of the paper tubes.

(3) Paper Width Adjustment: 79.5 ±0.5 to 111.5 ±0.5 mm Adjustable to any width.

3-6-2 Near-end Sensor

(1) Format: Reflective Type Photo-interrupter

(2) Width Direction Adjustment: 79.5 ±0.5 to 111.5 ±0.5 mm Adjustable to handle any width.

(3) Cable Length: 870 ±15 mm

Note 1) The near-end sensor cable length is determined according to the combination of optional

parts.

Remove the cable bundle when changing the layout of the printer or when using the optional

parts and printer unit. Also, be careful when removing the cable not to damage its insulating

cover.

(4) Residual Paper Amount (For Reference):

The residual amount to detect is adjusted by moving the near-end

sensor unit in the paper roll diameter direction.

See the following table regarding the paper roll that is detected by the

near-end sensor.

Also, see Fig. 8.5.2.A. for the applicable reference position.

Notes 1) See section 8.5 for details regarding the near-end sensor position.

2) The printer unit is adjusted to the reference position 'a' when shipped from the factory.

Table 3.6.2.3 Paper roll Sensor Diameter (For Reference)

Reference Position

Sensor Diameter

(Paper roll Outer Diameter)

Residual Paper Amount

(Calculated Value)

Reference 'a' φ41.5 8 m

Reference 'b' φ67.5 42 m

Reference 'c' φ93.5 93 m

Notes 1) The residual paper amounts described in the table above are for reference. Always check

that actual conditions of use to use this device.

2) Residual paper amounts described in the table above are for reference when using the

following types of paper roll.

Paper tube inner diameter: φ25.4

Paper tube outer diameter: φ32.4

Paper thickness: 65 µm

Rev 0.01

TUP900 Series Specifications Manual

3-12

3-7 Reliability Specifications

3-7-1 Thermal Mechanism Module

(1) Life: 15 million lines

(2) MCBF: 37 million lines

Note 1) If the recommended paper is not used, the life of the printer cannot be guaranteed. Always

use the recommended paper types.

3-7-2 Thermal Head

(1) Life: Withstanding of wear: 100 km; Durability to Pulses: 100 million pulses

(2) Two-color Printing Life: Withstanding of wear: 50 km; Durability to Pulses: 50 million pulses

Notes 1) This assumes repeated printing sequences below the printing rate of 12.5% based on STAR's

evaluation standards document.

2) This is a standard for life when more than two adjacent dots are damaged on the head.

However, this excludes damage (scratches) caused by the adherence of foreign matter or

man-made damages.

3) When repeated printing under extremely high printing rates, the life of the thermal head will

notable decrease. Carefully consider your print format before printing.

4) If the recommended paper is not used, the life of the printer cannot be guaranteed. Always

use the recommended paper types.

3-7-3 Auto-cutter

(1) Life: Must meet the number of cuts for the paper thickness.

Performs full cuts.

Paper thickness Life

65 µm to 100 µm One million cuts

100 µm to 150 µm Three-hundred thousand cuts

Note 1) If the recommended paper is not used, the life of the printer cannot be guaranteed. Always

use the recommended paper types.

3-7-4 Presenter Module

(1) Life: Ticketing operation can handle one million receipts.

Notes 1) This assumes repeated ticketing operations of 100 mm receipts, based on STAR's evaluation

standards document.

2) If the recommended paper is not used, the life of the printer cannot be guaranteed. Always

use the recommended paper types.

Rev 0.01

TUP900 Series Specifications Manual

4-1

4. EXTERNAL SPECIFICATIONS

4-1 External Specifications

4-1-1 External Dimensions

TUP992-24/TUP992-24J1: Width: 192 mm × Depth: 249.3 mm × Height: 179 mm

Note 1) These dimensions do not include paper roll or optional parts.

4-1-2 External Drawings

See Fig. 4.1.2 on the separate sheet.

4-1-3 Mass

2.84 ±0.02 kg

Note 1) Mass does not include paper roll or accessories (including optional parts).

4-2 Operation Panel Specifications

4-2-1 Switches

(1) POWER Switch: Turns the power of the main unit ON and OFF.

(2) SW 1: Feeds and discharges paper

Note 1) Be aware that the operation of the main unit may vary according to its conditions.

(3) SW 2: Clears errors

Note 1) Be aware that the operation of the main unit may vary according to its conditions.

4-2-2 LED

(1) LED 1: POWER: Green

(2) LED 2: ERROR: Red

4-3 Interface

No interface is included with this unit.

See section 2-2 for details on the optional interface card to use.

4-4 DIP Switches

Changeable on the top of the main unit (control board)

Notes 1) The direction for accessing the DIP switches may vary according to the layout of the control

board.

2) To access the DIP switches, it is necessary to remove the board chassis unit.

Rev 0.01

ries Specifications Manual

4-2

Fig. 4.1.2 External Dimensions Diagrams

TUP900 Se

Paper width center

4

b

a

80

94.6

90.1

17.1

249.3

117.5

102

3434

34

2

11

SW1

SW2

LED2

LED1

PULL

A

Paper width center

d

c

131.8

34

102

3434

88.188.1

9

176.2

6.8

192

(4)

(126.3)

17.1

1.5

84.8

32.4

58

133.7

116.6

17.1

146

179

73

(207)

DC24V

(117.1)

(13.7)

133.7

17.1

116.6

Rev 0.01

TUP900 Series Specifications Manual

5-1

5. ENVIRONMENT SPECIFICATIONS

5-1 Temperature and Humidity

5-1-1 When Operating

(1) Temperature: 0 to 50°C

However, printing is guaranteed at 5 to 50°C

(2) Humidity: 10 to 80% RH

However, there must be no condensation. Assumes 80% RH at 34°C

Note 1) When using the optional power adapter set, be aware that the operation guarantee range is

determined by the operating environment specifications of the power adapter set.

5-1-2 When Stored (Excluding Paper roll)

(1) Temperature: -20 to 60°C

(2) Humidity: 10 to 90% RH

However, there must be no condensation.

Note 1) The combination of 40°C and 90% RH (no condensation) is considered the worst values regarding

high temperatures and humidity.

0

10

20

30

40

50

60

70

80

Relative Humidity (%)

Ambient Temperature (°C)

010520304050

Fig. 5.1.1 Guaranteed Humidity Range

and

Guaranteed Printing Range

Guaranteed Operating Range

50

°

C 35% RH

40

°

C 58% RH

34

°

C 80% RH

Page is loading ...

Star Micronics TUP992-24J1 User manual

This manual is also suitable for

Star Micronics TUP992-24J1 User manual

Related papers

Other documents