Electrolux EQBL30AS User manual

Brand: Electrolux

Model: EQBL30AS

Type: User manual

This manual is also suitable for

user manual

Integrated BBQ 600/300mm

INTBBQ600/300_Jun11.indd 1 30/06/11 11:52 AM

2 contents electrolux integrated bbq 600/300mm

Congratulations

Congratulations and thank you for choosing our barbecue.

We are sure you will ﬁnd your new appliance a pleasure to

use. Before you use the appliance, we recommend that you

read through the entire user manual, which provides the

description of the appliance and its functions.

To avoid the risks that are always present when you use a

gas appliance, it is important that the appliance is installed

correctly and that you read the safety instructions carefully

to avoid misuse and hazards.

We recommend that you keep this instruction booklet

for future reference and pass it on to any future owners.

After unpacking the appliance please check it is not damaged.

If in doubt, do not use the appliance but contact your local

Electrolux Customer Care Centre.

CONDITIONS OF USE

This appliance is intended to be used in household and

similar applications such as:

• Farm houses

• By clients in holiday apartments and other residential

type environments.

Contents

• Important safety instructions 3

• Product Description 4

• Contents of Integrated BBQ 600/300mm 7

• Assembling the barbecue 8

• Gas specications 9

• Gas connection detail 9

• Natural gas installation 10

• Universal LPG installation 11

• Gas bottle safety information 12

• Leak test procedure 12

• Installation warnings 13

• Installation instructions 13

• Gas requirements 17

• Fitting the slimline lid or roasting hood 17

• Options for conguration of hotplates and grills 18

• Operating instructions 18

• Using the roasting hood 19

• Lid safety leg – slimline lid only 19

• Cleaning and care 20

• Maintenance 21

• Troubleshooting 21

• Notes 22

• Warranty 23

INTBBQ600/300_Jun11.indd 2 30/06/11 11:52 AM

electrolux integrated bbq 600/300mm important safety instructions 3

before you call

Please ensure you read the instruction manual fully

before you call for service, or a full service fee could

be applicable.

warning

This appliance MUST be installed and serviced by a

qualiﬁed licensed person only.

Improper installation, adjustment, alteration or maintenance

can cause injury or property damage. Please contact

your nearest Electrolux Service Department for additional

information or assistance for an approved installer.

NOTE TO THE INSTALLER

THIS MANUAL MUST REMAIN WITH THE OWNER FOR

FUTURE REFERENCE

warning

IF YOU SMELL GAS, do not attempt to light the barbecue.

Locate the leak and re-tighten the leaking joint. Carry out

the Leak Test procedure as described in this manual. If the

leak persists, turn off the gas supply and call Electrolux

Service or a Licensed Gas Fitter.

warning

Do not lean over barbecue when lighting.

Do not leave the barbecue unattended when alight.

Do not delay lighting once the gas has been turned on.

Do not store or use aerosol cans in the vicinity of

the barbecue.

Do not store ammable liquids in the vicinity of

the barbecue.

Do not use caustic or abrasive based cleaners

on the barbecue.

Do not operate the barbecue with the cover on.

Do not attempt to dismantle or adjust the

control valves.

Do not attempt to dismantle or adjust the regulator.

Do not test for leaks with a naked ame.

Do not modify the construction of this appliance or

modify the injector orice size.

Do not obstruct any ventilation of the barbecue.

Do not allow children to operate or play near

the barbecue.

caution

This barbecue is supplied set up for Natural Gas and

is labelled accordingly. A Universal LPG conversion

kit is available for purchase from Electrolux Service

or Spare Parts. Conversion of this unit to Universal

LPG must be carried out by a qualied licensed

person and a Certicate of Compliance must be

issued to the owner on completion of the

installation and conversion.

Important safety instructions

For your safety please read this user manual carefully

before operating your barbecue and store in a handy place

for later reference. Pass the user manual on to possible

new owners of the barbecue.

The symbols you will see in this booklet have these meanings:

warning

This symbol indicates information concerning your

personal safety

caution

This symbol indicates information on how to avoid

damaging the barbecue

tips and information

This symbol indicates tips and information about use

of the barbecue

environmental tip

This symbol indicates tips and information about

economical and ecological use of the barbecue

This symbol indicates never to do this

This symbol indicates always do this

environmental tip

Information on disposal for users

• Most of the packing materials are recyclable.

Please dispose of those materials through your local

recycling depot or by placing them in appropriate

collection containers.

• If you wish to discard this product, please contact

your local authorities and ask for the correct method

of disposal.

INTBBQ600/300_Jun11.indd 3 30/06/11 11:52 AM

4 product description electrolux integrated bbq 600/300mm

Product description EQBH60AS

1 Roasting hood

2 Temperature indicator

3 Burner controls

4 Warming racks

5 Grill

6 Hotplate

7 Gas connection point

INTBBQ600/300_Jun11.indd 4 30/06/11 11:52 AM

electrolux integrated bbq 600/300mm product description 5

Product description EQBL60AS

1 Slimline lid cover

2 Burner controls

3 Grill

4 Hotplate

5 Gas connection point

6 Pivoting leg

INTBBQ600/300_Jun11.indd 5 30/06/11 11:52 AM

6 product description electrolux integrated bbq 600/300mm

Product description EQBL30AS

1 Slimline lid cover

2 Burner control

3 Ribbed hotplate

4 Gas connection point (not illustrated)

5 Pivoting leg

INTBBQ600/300_Jun11.indd 6 30/06/11 11:52 AM

electrolux integrated bbq 600/300mm contents of integrated bbq 7

Contents of 600mm Integrated Barbecue Contents of 300mm Integrated Barbecue

item description qty

• EQB3BAS –

30cm mobile base

• EQB3LAS –

Small ﬂat lid with

mounting brackets

• Ribbed hotplate 1

• Rear heat shield 1

• Oil reservoir 1

• Hose 1

• Natural Gas

regulator

• Natural Gas hose 1

• Regulator mounting

bracket

Plastic bag containing

this instruction book,

match holder and chain,

trim panel screws,

regulator mounting

screws, and a blue

ﬁbre washer

item description qty

• EQB6BAS –

60cm built in base

• EQB6HAS –

Roasting hood and

warming racks

• EQB6LAS –

Flat lid with

mounting brackets

• Grills 2

• Hotplate 1

• Rear heat shield 1

• Flame tamers 2

• Oil reservoirs 2

• Natural Gas

installation pipe

• Natural Gas

regulator

• Natural Gas hose 1

Plastic bag containing

this instruction book,

match holder and chain,

trim panel screws and

2 blue ﬁbre washers

INTBBQ600/300_Jun11.indd 7 30/06/11 11:52 AM

8 assembling the bbq electrolux integrated bbq 600/300mm

Assembling the Barbecue

1. Remove packaging & remove all components

from packaging.

2. Attach rear heat shield to rear of unit by inserting the

top tabs into the rear holes and sliding the shield down.

3. Position ﬂame tamers (60cm model only) into desired

locations (under where grill sections will be ﬁtted) and ﬁx

back edge of the ﬂame tamer into rear of barbecue body

4. Ensure left and right hand oil reservoirs are ﬁtted

correctly at front of barbecue.

5. Place cooking plates into desired positions ensuring

that the ﬂame tamers are under the grill sections.

NOTE:

Ensure that all cooking plates are orientated correctly so

that the surface is sloping forward to allow oil to drain into

oil reservoirs.

6. After installation in a bench, attach a slimline lid or

roasting hood as described in “Fitting the slimline lid

or roasting hood” section of this manual.

INTBBQ600/300_Jun11.indd 8 30/06/11 11:52 AM

electrolux integrated bbq 600/300mm gas speciﬁcations 9

model EQBH60AS &

EQBL60AS

EQBL30AS

Gas type Natural

gas

Universal

LPG

Natural

gas

Universal

LPG

Maximum gas

consumption

46 MJ/h 46 MJ/h 11.5 MJ/h 11.5 MJ/h

Injector oriﬁce

diameter (mm)

1.50 0.90 1.50 0.90

Number of

injectors

4 4 1 1

Regulator

pressure

1.00kPa* 2.75kPa 1.00kPa* 2.75kPa

NOTE:

• This appliance MUST be installed and serviced by

a qualiﬁed licensed person only.

• This product is intended for outdoor use only.

• This product must be installed as per instructions

which requires the installation of venting to enable

the barbecue to operate correctly. Failure to provide

adequate ventillation for supply of air to the appliance

may result in poor burner performance or excessive

heat build-up within the mounting enclosure.

• Ventillation holes in the unit must not be obscured

by installation.

* The outlet pressure at the natural gas regulator will be

lower with all burners operating. Burner pressure should

read 1.0kPa with one burner operating and approximately

0.90kPa with four burners operating.

For conversion to Universal LPG a conversion kit will need

to be purchased from Electrolux Spare Parts.

EQBH60AS & EQBL60AS

EQBL30AS

Gas Speciﬁcations Gas connection detail

INTBBQ600/300_Jun11.indd 9 30/06/11 11:52 AM

10 natural gas installation electrolux integrated bbq 600/300mm

Preparing the unit for Natural Gas installation

This barbecue is supplied set up for Natural Gas and

is labelled accordingly. A Universal LPG conversion

kit is available from Electrolux Spare Parts if required.

Conversion of this unit to Universal LPG must be carried

out by a qualiﬁed licensed person.

A Certiﬁcate of Compliance must be issued to the owner

on completion of the installation and conversion.

EQBH60AS & EQBL60AS

1. Fitting the Natural Gas installation pipe

• Fit the pipe ensuring the blue sealing washer is in place.

Do not over-tighten.

2. Fitting the regulator

• Fit the regulator ensuring the blue sealing washer

is in place and the arrow indicating gas ﬂow direction

is correct. Do not over-tighten.

3. Fit the hose

• Apply thread tape or sealant to the male thread on the

hose and screw into the regulator. Do not over-tighten.

barbecue gas inlet

sealing washer

regulator – ensure arrow is

pointing in the right direction

1/2” BSP tapered thread hose

– thread tape required

natural gas installation pipe

4. Fit to mains

• Connect the bayonet end to mains.

EQBL30AS

1. Fit ﬂexible black hose to the gas inlet. Do not over-tighten.

2. Fit the brass adaptor to the black ﬂexible hose. Do not

over-tighten.

3. Fit the regulator to the adaptor with ﬁbre washer

ensuring that ﬁbre washer seated correctly into adaptor.

Do not over-tighten.

4. Fit the hose to the regulator

• Apply thread tape or sealant to the male thread on the

hose and screw into the regulator. Do not over-tighten.

gas hose 500mm

brass adaptor

sealing washer

securing bracket

1/2” BSP tapered

thread hose – thread

tape required

regulator – ensure

arrow is pointing in

the right direction

5. Secure regulator using bracket supplied

6. Fit to mains

• Connect the bayonet end to mains.

7. Ensure routing of gas supply hose prevents the hose from

contacting hot surfaces of burner base or burner box.

8. Complete leak test of ﬁnal assemby. (refer to page 12)

Natural Gas installation

INTBBQ600/300_Jun11.indd 10 30/06/11 11:52 AM

electrolux integrated bbq 600/300mm universal LPG installation 11

Preparing the unit for Universal LPG installation

This barbecue is supplied set up for Natural Gas and is

labelled accordingly. A Universal LPG conversion kit is

available from Electrolux Spare Parts to enable conversion

to Universal LPG and connection to a 9kg bottle.

Remote ULPG supply

The barbecue can be plumbed into a remote or

household ULPG supply. Never connect the barbecue

to an unregulated supply, ensure supply pressure at the

barbecue is 2.75kPa. Electrolux strongly recommends that

a manual shut off valve be installed in the gas supply line in

an accessible position so that gas can be turned off in the

event of an emergency, or during servicing.

NOTE:

Conversion of this unit to Universal LPG must be carried

out by a qualiﬁed licensed person and a Certiﬁcate of

Compliance must be issued to the owner on completion

of the installation and conversion. The components are:

For models EQBH60AS & EQBL60AS

• Hose and regulator assembly

• Small plastic bag containing 4 brass injectors (0.90mm)

• 1 Universal LPG sticker

• 1 brass adaptor

• 1 sealing washer

For models EQBL30AS

• Hose and regulator assembly

• Small plastic bag containing 1 brass injector (0.90mm)

• 1 Universal LPG sticker

1. Change the injectors

• Remove the front cover.

• Remove the burner retaining clips as shown.

remove spring clip

by rotating over

burner tube end

front cover

• Unscrew and replace the injector nipples located in the

end of each tube feeding the burners. The Universal LPG

injectors have a 0.90mm diameter oriﬁce in them. They

appear substantially smaller than the Natural Gas injectors.

LPG injector

• Re-fasten the clip to retain the tube in the burner.

Do not over tighten or distort supply tube.

• Fit the front cover back on and fasten screws.

2. Adjust the turndown setting on the valve

• Remove the knobs from the valves.

• Remove rubber grommets from control panel holes.

• For each valve rotate the valve rotation limiting screw

anti-clockwise using a Philips head screw driver until

valve shaft is able to be rotated more than 180°

(approx 3 turns).

Valve rotation

limiting screw

• Re-t grommets and knobs

3. For EQBH60AS & EQBL60AS only, connect the adaptor

to the barbecue gas inlet. Ensure the blue sealing

washer is in place. Do not over tighten.

4. Connect the hose. Do not over tighten.

5. Following connection to gas bottle, conduct a leak test

for all joints made (refer leak test procedure page 12).

6. Light all burners and one at a time set the burner to the

lowest setting and check a small steady ﬂame is achieved.

EQBH60AS & EQBL60AS

barbecue gas inlet

sealing washer

brass adaptor

LPG hose and

regulator assembly

EQBL30AS

LPG hose and regulator assembly

gas inlet

7. Replace the ‘gas type’ sticker

• Locate the ‘Natural Gas’ sticker located on or near the gas

inlet and remove it. Put the Universal LPG sticker in its place.

Universal LPG installation

INTBBQ600/300_Jun11.indd 11 30/06/11 11:52 AM

12 gas bottle safety & leak test electrolux integrated bbq 600/300mm

• This appliance is designed to use a Universal LPG

9kg (20 lbs) gas cylinder.

• The gas cylinder must be made and marked in

accordance with speciﬁcations for LPG cylinders.

• It is recommended to turn off the cylinder valve when

the appliance is not in use.

• Gas cylinders must be stored in an approved housing

out of reach of children.

• When disconnecting the gas bottle ensure that all the

control valves are in the ‘OFF’ position.

• Remove the bottle from any housing in which it may be

stored before disconnection.

• When reconnecting the hose to the bottle, ensure that

all connections are tight before replacing in the storage

compartment.

• Carry out a leakage check as detailed on this page after

each re-connection.

• Ensure all gas valves are in the ‘OFF’ position.

• In a small container, mix a solution of water and

detergent or soap.

• After connection of the hose, turn on the valve at the

gas bottle or mains as appropriate.

• Using a brush apply the solution to the gas connection

points and look for bubbles forming.

• Bubbling will indicate a leak.

• Turn off the valve and re-tighten the joint. Repeat the

leak test.

• If the leak persists, turn off the gas at the isolation valve

and contact a licensed gas ﬁtter to correct.

EQBH60AS & EQBL60AS

check for leaks

check hose for signs of

abrasions, cracks or leaks

EQBL30AS

leak test points

Gas bottle safety information Leak test procedure

INTBBQ600/300_Jun11.indd 12 30/06/11 11:52 AM

electrolux integrated bbq 600/300mm installation 13

Installation warnings Installation instructions

warning

• This appliance shall only be used in an above ground,

open air situation with natural ventilation without

stagnant areas, where gas leakage and products of

combustion are rapidly dispersed by wind or natural

convection. This barbecue has been designed for

outdoor use only. Refer to diagrams below.

• Never install this barbecue inside any building,

garage, shed or breezeway or inside a boat, caravan

or recreational vehicle. This is to prevent the possibility

of ﬁre, carbon monoxide poisoning or asphyxiation.

• Any enclosure in which this appliance is installed

shall comply with one of the following:

– An enclosure with walls on all sides, but at least one

permanent opening at the ground level and

no overhead covering.

– Within a partial enclosure that includes an overhead

cover and no more than 2 walls.

– Within a partial enclosure that includes an overhead

cover and more than 2 walls, the following shall apply:

– at least 25% of the total wall area is completely open

and at least 30% of the remaining wall area is open

and unrestricted.

• In the case of balconies, at least 20% of the total of

the side, back and front wall areas shall be and remain

open and unrestricted.

Outdoor area example 1

Outdoor area example 2

Outdoor area example 3

Outdoor area example 4

Outdoor area example 5

Choosing a location

• This appliance must not be installed on any combustible

material. A minimum clearance from any combustible

material is 450mm.

• The vertical clearance above the cooking surface to

any combustible materials must be at least 600mm.

• This appliance must be installed in accordance with

Australian Standards AS4557 and AS5601 and in

accordance with the local authority.

• When using LPG in an enclosure ventilation must be

provided. Gas is highly explosive and can cause serious

injury and damage to property if allowed to accumulate

and then be ignited.

• This barbecue is intended to be built into a benchtop

with a minimum depth of 600mm.

• Avoid windy positions as this will affect cooking

performance and burner efﬁciency. If this situation

cannot be avoided some shielding may be necessary.

• If the chosen location is exposed to rain consideration

will need to be given for water drainage. Some of the

rain can drain through the benchtop hole and through

the product.

The mounting enclosure

• The barbecue requires a non-combustible barrier under

the barbecue to prevent excessive temperatures being

accessed. The barrier panel is to be placed 30mm

under the base of the unit. There are spacers added to

the bottom of the unit to prevent barrier panel being too

close to barbecue base. Refer to diagram next page.

• The mounting enclosure must be constructed from

non-combustible materials. Suitable materials for

construction include masonry, granite, marble,

Hardiplank

, Villaboard

, over a metal frame or tiles.

• This appliance requires venting in the enclosure, see

diagrams for details.

• This appliance can be mounted either in an island type

bench or a bench with a splashback. Please read the

speciﬁc requirements for each mounting situation.

• For ULPG use, cabinetry below the barbecue must

have low level ventilation to prevent the possibility of

ULPG accumulating.

Island style installation

• If the appliance is installed in an island mount, it can be

centrally positioned. Special attention should be given

to the overall size of the island top to consider the hood

open and overhang.

• The cut-out size required for models EQBH60AS &

EQBL60AS is 735mm x 502mm.

• The cut-out size required for model EQBL30AS is

440mm x 502mm (as shown on page 15).

both ends

open

open side at

least 25% of

total wall area

30% or more in total of

the remaining wall area

is open and unrestricted

open side at

least 25% of

total wall area

30% or more in total of

the remaining wall area

is open and unrestricted

INTBBQ600/300_Jun11.indd 13 30/06/11 11:52 AM

14 installation electrolux integrated bbq 600/300mm

bench width 600 min

539

464

202

590

538

464

202 212

warning

• This appliance requires venting. An open area as

indicated below must be allowed for. A suitable grille

can be ﬁtted if desired. This vent area is to allow air

into the enclosure for the correct combustion of gases

and for the correct exhausting of the products of

combustion. This vent must be 600mm x 25mm for

models EQBH60AS & EQBL60AS, and 300mm x 25mm

for model EQBL30AS. See location options on pg16.

Installing in a bench with a splashback

• The splashback must be made from a

non-combustible material.

• In the case of mounting this appliance against a wall

or fence it is imperative that care is taken to ensure

the isolation of combustible materials. All combustible

materials must be kept 450mm away from the barbecue.

• For roasting hood model there is a specic minimum

clearance required at the back of the barbecue between

the splashback and the bench cut-out of 73mm.

This is to allow clearance to open.

73 min to bench cut out

547

73 min to bench cut out

603

INTBBQ600/300_Jun11.indd 14 30/06/11 11:53 AM

electrolux integrated bbq 600/300mm installation 15

80 min

INTBBQ600/300_Jun11.indd 15 30/06/11 11:53 AM

16 installation electrolux integrated bbq 600/300mm

Venting options

There are two venting options that can be used. The ﬁrst is

in the front of enclosure (see diagram below for requirements).

The second is in the barrier panel below the barbecue.

If an LPG bottle is to be stored under the barbecue,

it must be isolated from the vent in the barrier panel.

Front vent option – to be located centrally to burner box

EQBL30AS

EQBH60AS & EQBL60AS

135

600

300

Base vent option (enclosure front removed for clarity) – to be located centrally to burner box

EQBL30AS

EQBH60AS & EQBL60AS

600

300

INTBBQ600/300_Jun11.indd 16 30/06/11 11:53 AM

electrolux integrated bbq 600/300mm gas requirements & ﬁtting 17

Gas requirements

Natural Gas requirements

• The enclosure must be constructed so that access

can be gained to the Natural Gas regulator at all times.

• For Natural Gas the gas supply is required to be

connected to 1.2m ﬂexible hose supplied and therefore

must be located within this distance.

• The exible hose has a quick connect gas coupling.

The corresponding mating ﬁtting will be required at

the gas supply end.

• For pipe sizing requirements for supply pipe refer

to AS5601.

Universal LPG Requirements

warning

• If an LPG bottle is to be stored in the enclosure under

the barbecue unit, it must be isolated from the barbecue

unit with a non-combustible panel.

The enclosure must comply with the requirements

of AS5601.

• AS5601 ventilation requirements for cylinder storage are:

Where of sheet metal or similar impervious construction

there shall be ventilation openings at the top and bottom

of the enclosure or recess, each opening providing a

free area of at least 200cm2 for every cylinder enclosed.

• For ULPG installations having enclosed cabinetry below

the separation panel that does not contain a gas bottle,

low level venting must be installed. This is to allow the

gas which is heavier than air escape from the enclosure

in the situation where there may be a leak. A minimum

opening of 200cm

is required.

Setting up the barbecue

Setting up the barbecue in mounting enclosure

• A match holder with attached chain has been included

with the instruction manual. This is provided for manual

ignition in the event the automatic ignition does not work.

The free end of chain is required to be permanently ﬁxed

to the installation in a location that enables the match

holder to reach each burner (refer to page 18 for manual

lighting instructions).

• After the enclosure has been constructed as described

on page 13, position the assembled barbecue into the

cut-out hole.

• Check that the barbecue is level and is rmly supported.

• Connect to gas supply (Universal LPG or Natural Gas)

and leak test.

• For tment of the slimline lid or roasting hood (see right).

Fitting the slimline lid or roasting hood

Fitting of slimline lid

• Unpack the slimline lid.

• Remove side screws from barbecue trim surround

using a philips head screw driver.

• Cooking plates should be removed in order to attach

hinge bracket.

• Fit brackets to trim surround with the same screws.

• Fit lid to brackets.

Fitting of roasting hood

• Unpack the roasting hood.

• Remove side and rear screws from barbecue trim

surround using a philips head screw driver.

• Cooking plates should be removed in order to attach

hinge bracket.

warning

Due to the size of the roasting hood, it is recommended

that two people place the roasting hood into position.

• When tting roasting hood assembly, take particular

care to avoid scratching of the external trim.

• Once in position, x hood assembly to trim surround

with same screws.

INTBBQ600/300_Jun11.indd 17 30/06/11 11:53 AM

18 options & operating instructions electrolux integrated bbq 600/300mm

Operating instructionsOptions for conﬁguration of hotplates

and grills

Before lighting the barbecue:

• Check that all hoses and gas ttings are tight.

• Open the roasting hood or slimline lid.

NOTE:

The slimline lid is designed as a cover for weather protection.

The lid is not designed to be used as a cooking hood.

• Check all control knobs are in the ‘OFF’ position.

• Ensure that the cooking surfaces are clean.

• Turn the gas isolation valve ‘ON’.

Lighting instructions

• Do not attempt to light burners with cooking

surfaces covered.

• Read instructions before lighting.

• To light a burner, depress the knob and rotate to

‘HIGH HEAT’. A spark is generated to light the ﬂame

thrower alongside the burner. The ﬂame thrower makes

an audible noise and only operates when the knob is

depressed to light burner. Release the knob and check

if the burner is alight, note that the audible noise from

the ﬂame thrower will stop when the knob is released.

• If the burner did not light, turn the knob to the ‘OFF’ position.

Allow gas to disperse, then repeat lighting procedure.

Manual lighting

• If, in the event of the automatic ignition system not

working, the barbecue can be lit manually.

• To light manually, t a 40mm match to match holder

provided. Pass lit match through viewing slots below the

front of cooking plates down towards the burner, then

rotate the knob to HIGH HEAT to ignite. If ignition fails,

turn the control valve off and allow several minutes for

the gas to disperse before attempting to light again.

• Once alight, repeat for other burners as required.

pass match holder

through viewing slot at

front under cooking plates

Preheating

• This barbecue is tted with high power burners. In most

conditions it will only be necessary to preheat the barbecue

for 5 minutes before cooking can commence.

• As with most things, experience will familiarise you with the

effectiveness of and the time required to achieve the desired

preheating time to obtain the desired cooking temperature.

• Testing has shown that the burners can be turned

to low position for satisfactory cooking.

• If the unit does not operate correctly refer to the

troubleshooting section on page 21.

For EQBH60AS & EQBL60AS the grills and hot plate can

be positioned as desired.

For roasting (EQBH60AS only) it is recommended to place

the hotplate in the middle and a grill plate each side.

warning

Ensure ﬂame tamers are positioned under grill panels.

Alternative arrangement when not roasting

INTBBQ600/300_Jun11.indd 18 30/06/11 11:53 AM

electrolux integrated bbq 600/300mm usage & lid safety leg 19

• If the burners are left to run too hot there will be excessive

smoking during the cooking process and subsequent

burning of the food being prepared. This may also result

in excessive ﬂaring of the fat being emitted from the food.

• Roasting with the hood closed only requires the 2

outermost burners on low setting for satisfactory cooking.

Refer below for further information on roasting.

To turn the burner off

• When cooking is complete, rotate the knob fully clockwise

so the pointer on the knob is positioned at the ‘OFF’ position.

• Turn gas bottle isolation valve off after turning all knobs

to ‘OFF’ position when appliance not in use.

Using the roasting hood

Cooking with the hood closed only requires 2 burners to be

on low setting. The setting is to be adjusted depending on

conditions and using the temperature indicator as a guide.

• It is recommended when roasting to place the solid

hot plate in the centre with one grill on each side of

the plate. Use the two outer burners under the grills.

• To achieve even cooking of the food, place the food

onto a wire rack above the hot plate to allow air to

circulate under the food.

• Food can also be placed on the warming racks for

cooking with hood closed

warning

• Do not use more than 2 burners when the hood is

closed and do not allow the temperature to exceed

the ‘Ready’ zone of the temperature indicator. These

conditions create excessive heat and may cause

damage to the barbecue and roasting hood.

• When cooking with the hood closed the hot ue

gases ﬂow out the rear of the appliance between

the splashguard and the hood. Ensure the barbecue

is suitably located to avoid damage or injury.

Lid safety leg – slimline lid only

To ensure that the user remembers to turn off the gas

before closing the lid, a pivoting safety leg has been ﬁtted

(both small and large lids).

pivoting safety leg

When closing the lid the safety leg will pivot forward and

rest against the trim surface to prevent the lid closing.

After ensuring the gas has been turned off, the lid can be

fully closed by rotating the leg backwards.

pivoting safety leg

warning

THE SLIMLINE LID MUST NOT BE CLOSED WHEN THE

BURNERS ARE OPERATING.

Closing the lid during burner operation can cause

discolouration and damage to the lid and barbecue unit.

INTBBQ600/300_Jun11.indd 19 30/06/11 11:53 AM

20 cleaning and care electrolux integrated bbq 600/300mm

Cleaning and care

This Electrolux barbecue has been constructed from select

grade stainless steel which, if not cared for, may discolour

over time. To keep your barbecue looking its best we

recommend that the cooking surfaces are cleaned after

every use.

warning

Please ensure that your barbecue is switched off and

has cooled down before following the instructions below.

Cast iron plates and plate surround cleaning

The cooking plates and grills have a porcelain enamelled

coating and must be at ambient temperature before cleaning.

NOTE:

Many food acids, juices, marinades and sauces contain

highly acidic elements that will slowly attack the surface

of the cast iron if not removed immediately after cooking.

After use remove all solid material from the cooking surface

using a brass bristled barbecue brush or plastic bristled

scourer. Wipe off the remaining grease with paper towelling.

Gently wash the surfaces with a cloth or sponge and a mild

detergent and hot water. Dry components immediately and

coat the cooking surface with a light layer of cooking oil.

This protects the surface when not in use. Do not clean

the cooking surface in a dishwasher

Cleaning stainless steel surfaces

caution

Do not use abrasive or caustic cleaners, scourers or

metal scrapers on stainless steel surfaces as they may

permanently scratch and damage your barbecue.

• Wash all stainless steel components, including the

slimline lid, the roasting hood, tubular frame and control

knobs with a soft dishcloth using hot soapy water

• The barbecue interior can be wiped down with a soft

cloth in hot soapy water. The rear panel of the interior

is removable for easy cleaning

• Ensure that all surfaces are dried with a clean dry cloth

tips and information

Sometimes stainless steel surfaces are affected by a brown

discolouration called tea staining. This usually occurs in

areas which use high heat and can be removed using

specialised stainless steel cleaners. For best results, we

recommend that specialised cleaners be used regularly on

all stainless steel components. You will ﬁnd these cleaners

at Electrolux spare parts outlets.

caution

Take extra care (particularly when cleaning on and around

the control knobs) to ensure that water and soapy residue

do not enter the control panel.

Care should also be taken not to disturb the spark electrode.

Cleaning the oil reservoirs

The electrolux integrated bbq 600/300mm has a unique oil

management system which uses overlapping channels to

drain all oil to the front into easily removed reservoirs and

should be cleaned after each use.

• To remove reservoirs, pull upwards from the front of the

barbecue and dispose of the contents of the catchment

responsibly. Rinse oil reservoirs in warm soapy water.

The reservoirs can be placed in the dishwasher if desired.

tips and information

The stainless steel panels may distort while in use but will

return to normal when cold.

INTBBQ600/300_Jun11.indd 20 30/06/11 11:53 AM

Page is loading ...

Electrolux EQBL30AS User manual

Brand: Electrolux

Model: EQBL30AS

Type: User manual

This manual is also suitable for

Download PDF

report

Electrolux EQBL30AS User manual

This manual is also suitable for

Electrolux EQBL30AS User manual

Related papers

Other documents