user manual
Integrated BBQ 600/300mm
INTBBQ600/300_Jun11.indd 1 30/06/11 11:52 AM
2 contents electrolux integrated bbq 600/300mm
Congratulations
Congratulations and thank you for choosing our barbecue.
We are sure you will find your new appliance a pleasure to
use. Before you use the appliance, we recommend that you
read through the entire user manual, which provides the
description of the appliance and its functions.
To avoid the risks that are always present when you use a
gas appliance, it is important that the appliance is installed
correctly and that you read the safety instructions carefully
to avoid misuse and hazards.
We recommend that you keep this instruction booklet
for future reference and pass it on to any future owners.
After unpacking the appliance please check it is not damaged.
If in doubt, do not use the appliance but contact your local
Electrolux Customer Care Centre.
CONDITIONS OF USE
This appliance is intended to be used in household and
similar applications such as:
• Farm houses
• By clients in holiday apartments and other residential
type environments.
Contents
• Important safety instructions 3
• Product Description 4
• Contents of Integrated BBQ 600/300mm 7
• Assembling the barbecue 8
• Gas specications 9
• Gas connection detail 9
• Natural gas installation 10
• Universal LPG installation 11
• Gas bottle safety information 12
• Leak test procedure 12
• Installation warnings 13
• Installation instructions 13
• Gas requirements 17
• Fitting the slimline lid or roasting hood 17
• Options for conguration of hotplates and grills 18
• Operating instructions 18
• Using the roasting hood 19
• Lid safety leg – slimline lid only 19
• Cleaning and care 20
• Maintenance 21
• Troubleshooting 21
• Notes 22
• Warranty 23
INTBBQ600/300_Jun11.indd 2 30/06/11 11:52 AM
electrolux integrated bbq 600/300mm important safety instructions 3
before you call
Please ensure you read the instruction manual fully
before you call for service, or a full service fee could
be applicable.
warning
This appliance MUST be installed and serviced by a
qualified licensed person only.
Improper installation, adjustment, alteration or maintenance
can cause injury or property damage. Please contact
your nearest Electrolux Service Department for additional
information or assistance for an approved installer.
NOTE TO THE INSTALLER
THIS MANUAL MUST REMAIN WITH THE OWNER FOR
FUTURE REFERENCE
warning
IF YOU SMELL GAS, do not attempt to light the barbecue.
Locate the leak and re-tighten the leaking joint. Carry out
the Leak Test procedure as described in this manual. If the
leak persists, turn off the gas supply and call Electrolux
Service or a Licensed Gas Fitter.
warning
Do not lean over barbecue when lighting.
Do not leave the barbecue unattended when alight.
Do not delay lighting once the gas has been turned on.
Do not store or use aerosol cans in the vicinity of
the barbecue.
Do not store ammable liquids in the vicinity of
the barbecue.
Do not use caustic or abrasive based cleaners
on the barbecue.
Do not operate the barbecue with the cover on.
Do not attempt to dismantle or adjust the
control valves.
Do not attempt to dismantle or adjust the regulator.
Do not test for leaks with a naked ame.
Do not modify the construction of this appliance or
modify the injector orice size.
Do not obstruct any ventilation of the barbecue.
Do not allow children to operate or play near
the barbecue.
caution
This barbecue is supplied set up for Natural Gas and
is labelled accordingly. A Universal LPG conversion
kit is available for purchase from Electrolux Service
or Spare Parts. Conversion of this unit to Universal
LPG must be carried out by a qualied licensed
person and a Certicate of Compliance must be
issued to the owner on completion of the
installation and conversion.
Important safety instructions
For your safety please read this user manual carefully
before operating your barbecue and store in a handy place
for later reference. Pass the user manual on to possible
new owners of the barbecue.
The symbols you will see in this booklet have these meanings:
warning
This symbol indicates information concerning your
personal safety
caution
This symbol indicates information on how to avoid
damaging the barbecue
tips and information
This symbol indicates tips and information about use
of the barbecue
environmental tip
This symbol indicates tips and information about
economical and ecological use of the barbecue
This symbol indicates never to do this
This symbol indicates always do this
environmental tip
Information on disposal for users
• Most of the packing materials are recyclable.
Please dispose of those materials through your local
recycling depot or by placing them in appropriate
collection containers.
• If you wish to discard this product, please contact
your local authorities and ask for the correct method
of disposal.
INTBBQ600/300_Jun11.indd 3 30/06/11 11:52 AM
4 product description electrolux integrated bbq 600/300mm
Product description EQBH60AS
2
6
1
4
4
3
5
5
7
1 Roasting hood
2 Temperature indicator
3 Burner controls
4 Warming racks
5 Grill
6 Hotplate
7 Gas connection point
INTBBQ600/300_Jun11.indd 4 30/06/11 11:52 AM
electrolux integrated bbq 600/300mm product description 5
Product description EQBL60AS
6
1
4
2
3
3
5
1 Slimline lid cover
2 Burner controls
3 Grill
4 Hotplate
5 Gas connection point
6 Pivoting leg
INTBBQ600/300_Jun11.indd 5 30/06/11 11:52 AM
6 product description electrolux integrated bbq 600/300mm
Product description EQBL30AS
3
1
2
5
1 Slimline lid cover
2 Burner control
3 Ribbed hotplate
4 Gas connection point (not illustrated)
5 Pivoting leg
INTBBQ600/300_Jun11.indd 6 30/06/11 11:52 AM
electrolux integrated bbq 600/300mm contents of integrated bbq 7
Contents of 600mm Integrated Barbecue Contents of 300mm Integrated Barbecue
item description qty
• EQB3BAS –
30cm mobile base
1
• EQB3LAS –
Small flat lid with
mounting brackets
1
• Ribbed hotplate 1
• Rear heat shield 1
• Oil reservoir 1
• Hose 1
• Natural Gas
regulator
1
• Natural Gas hose 1
• Regulator mounting
bracket
Plastic bag containing
this instruction book,
match holder and chain,
trim panel screws,
regulator mounting
screws, and a blue
fibre washer
1
item description qty
• EQB6BAS –
60cm built in base
1
• EQB6HAS –
Roasting hood and
warming racks
OR
• EQB6LAS –
Flat lid with
mounting brackets
1
• Grills 2
• Hotplate 1
• Rear heat shield 1
• Flame tamers 2
• Oil reservoirs 2
• Natural Gas
installation pipe
1
• Natural Gas
regulator
1
• Natural Gas hose 1
Plastic bag containing
this instruction book,
match holder and chain,
trim panel screws and
2 blue fibre washers
1
OR
INTBBQ600/300_Jun11.indd 7 30/06/11 11:52 AM
8 assembling the bbq electrolux integrated bbq 600/300mm
Assembling the Barbecue
1. Remove packaging & remove all components
from packaging.
2. Attach rear heat shield to rear of unit by inserting the
top tabs into the rear holes and sliding the shield down.
3. Position flame tamers (60cm model only) into desired
locations (under where grill sections will be fitted) and fix
back edge of the flame tamer into rear of barbecue body
4. Ensure left and right hand oil reservoirs are fitted
correctly at front of barbecue.
5. Place cooking plates into desired positions ensuring
that the flame tamers are under the grill sections.
NOTE:
Ensure that all cooking plates are orientated correctly so
that the surface is sloping forward to allow oil to drain into
oil reservoirs.
6. After installation in a bench, attach a slimline lid or
roasting hood as described in “Fitting the slimline lid
or roasting hood” section of this manual.
INTBBQ600/300_Jun11.indd 8 30/06/11 11:52 AM
electrolux integrated bbq 600/300mm gas specifications 9
model EQBH60AS &
EQBL60AS
EQBL30AS
Gas type Natural
gas
Universal
LPG
Natural
gas
Universal
LPG
Maximum gas
consumption
46 MJ/h 46 MJ/h 11.5 MJ/h 11.5 MJ/h
Injector orifice
diameter (mm)
1.50 0.90 1.50 0.90
Number of
injectors
4 4 1 1
Regulator
pressure
1.00kPa* 2.75kPa 1.00kPa* 2.75kPa
NOTE:
• This appliance MUST be installed and serviced by
a qualified licensed person only.
• This product is intended for outdoor use only.
• This product must be installed as per instructions
which requires the installation of venting to enable
the barbecue to operate correctly. Failure to provide
adequate ventillation for supply of air to the appliance
may result in poor burner performance or excessive
heat build-up within the mounting enclosure.
• Ventillation holes in the unit must not be obscured
by installation.
* The outlet pressure at the natural gas regulator will be
lower with all burners operating. Burner pressure should
read 1.0kPa with one burner operating and approximately
0.90kPa with four burners operating.
For conversion to Universal LPG a conversion kit will need
to be purchased from Electrolux Spare Parts.
EQBH60AS & EQBL60AS
EQBL30AS
Gas Specifications Gas connection detail
INTBBQ600/300_Jun11.indd 9 30/06/11 11:52 AM
10 natural gas installation electrolux integrated bbq 600/300mm
Preparing the unit for Natural Gas installation
This barbecue is supplied set up for Natural Gas and
is labelled accordingly. A Universal LPG conversion
kit is available from Electrolux Spare Parts if required.
Conversion of this unit to Universal LPG must be carried
out by a qualified licensed person.
A Certificate of Compliance must be issued to the owner
on completion of the installation and conversion.
EQBH60AS & EQBL60AS
1. Fitting the Natural Gas installation pipe
• Fit the pipe ensuring the blue sealing washer is in place.
Do not over-tighten.
2. Fitting the regulator
• Fit the regulator ensuring the blue sealing washer
is in place and the arrow indicating gas flow direction
is correct. Do not over-tighten.
3. Fit the hose
• Apply thread tape or sealant to the male thread on the
hose and screw into the regulator. Do not over-tighten.
barbecue gas inlet
sealing washer
sealing washer
regulator – ensure arrow is
pointing in the right direction
1/2” BSP tapered thread hose
– thread tape required
natural gas installation pipe
4. Fit to mains
• Connect the bayonet end to mains.
EQBL30AS
1. Fit flexible black hose to the gas inlet. Do not over-tighten.
2. Fit the brass adaptor to the black flexible hose. Do not
over-tighten.
3. Fit the regulator to the adaptor with fibre washer
ensuring that fibre washer seated correctly into adaptor.
Do not over-tighten.
4. Fit the hose to the regulator
• Apply thread tape or sealant to the male thread on the
hose and screw into the regulator. Do not over-tighten.
gas hose 500mm
brass adaptor
sealing washer
securing bracket
1/2” BSP tapered
thread hose – thread
tape required
regulator – ensure
arrow is pointing in
the right direction
5. Secure regulator using bracket supplied
6. Fit to mains
• Connect the bayonet end to mains.
7. Ensure routing of gas supply hose prevents the hose from
contacting hot surfaces of burner base or burner box.
8. Complete leak test of final assemby. (refer to page 12)
Natural Gas installation
INTBBQ600/300_Jun11.indd 10 30/06/11 11:52 AM
electrolux integrated bbq 600/300mm universal LPG installation 11
Preparing the unit for Universal LPG installation
This barbecue is supplied set up for Natural Gas and is
labelled accordingly. A Universal LPG conversion kit is
available from Electrolux Spare Parts to enable conversion
to Universal LPG and connection to a 9kg bottle.
Remote ULPG supply
The barbecue can be plumbed into a remote or
household ULPG supply. Never connect the barbecue
to an unregulated supply, ensure supply pressure at the
barbecue is 2.75kPa. Electrolux strongly recommends that
a manual shut off valve be installed in the gas supply line in
an accessible position so that gas can be turned off in the
event of an emergency, or during servicing.
NOTE:
Conversion of this unit to Universal LPG must be carried
out by a qualified licensed person and a Certificate of
Compliance must be issued to the owner on completion
of the installation and conversion. The components are:
For models EQBH60AS & EQBL60AS
• Hose and regulator assembly
• Small plastic bag containing 4 brass injectors (0.90mm)
• 1 Universal LPG sticker
• 1 brass adaptor
• 1 sealing washer
For models EQBL30AS
• Hose and regulator assembly
• Small plastic bag containing 1 brass injector (0.90mm)
• 1 Universal LPG sticker
1. Change the injectors
• Remove the front cover.
• Remove the burner retaining clips as shown.
remove spring clip
by rotating over
burner tube end
front cover
• Unscrew and replace the injector nipples located in the
end of each tube feeding the burners. The Universal LPG
injectors have a 0.90mm diameter orifice in them. They
appear substantially smaller than the Natural Gas injectors.
LPG injector
• Re-fasten the clip to retain the tube in the burner.
Do not over tighten or distort supply tube.
• Fit the front cover back on and fasten screws.
2. Adjust the turndown setting on the valve
• Remove the knobs from the valves.
• Remove rubber grommets from control panel holes.
• For each valve rotate the valve rotation limiting screw
anti-clockwise using a Philips head screw driver until
valve shaft is able to be rotated more than 180°
(approx 3 turns).
Valve rotation
limiting screw
• Re-t grommets and knobs
3. For EQBH60AS & EQBL60AS only, connect the adaptor
to the barbecue gas inlet. Ensure the blue sealing
washer is in place. Do not over tighten.
4. Connect the hose. Do not over tighten.
5. Following connection to gas bottle, conduct a leak test
for all joints made (refer leak test procedure page 12).
6. Light all burners and one at a time set the burner to the
lowest setting and check a small steady flame is achieved.
EQBH60AS & EQBL60AS
barbecue gas inlet
sealing washer
brass adaptor
LPG hose and
regulator assembly
EQBL30AS
LPG hose and regulator assembly
gas inlet
7. Replace the ‘gas type’ sticker
• Locate the ‘Natural Gas’ sticker located on or near the gas
inlet and remove it. Put the Universal LPG sticker in its place.
Universal LPG installation
INTBBQ600/300_Jun11.indd 11 30/06/11 11:52 AM
12 gas bottle safety & leak test electrolux integrated bbq 600/300mm
• This appliance is designed to use a Universal LPG
9kg (20 lbs) gas cylinder.
• The gas cylinder must be made and marked in
accordance with specifications for LPG cylinders.
• It is recommended to turn off the cylinder valve when
the appliance is not in use.
• Gas cylinders must be stored in an approved housing
out of reach of children.
• When disconnecting the gas bottle ensure that all the
control valves are in the ‘OFF’ position.
• Remove the bottle from any housing in which it may be
stored before disconnection.
• When reconnecting the hose to the bottle, ensure that
all connections are tight before replacing in the storage
compartment.
• Carry out a leakage check as detailed on this page after
each re-connection.
• Ensure all gas valves are in the ‘OFF’ position.
• In a small container, mix a solution of water and
detergent or soap.
• After connection of the hose, turn on the valve at the
gas bottle or mains as appropriate.
• Using a brush apply the solution to the gas connection
points and look for bubbles forming.
• Bubbling will indicate a leak.
• Turn off the valve and re-tighten the joint. Repeat the
leak test.
• If the leak persists, turn off the gas at the isolation valve
and contact a licensed gas fitter to correct.
EQBH60AS & EQBL60AS
check for leaks
check hose for signs of
abrasions, cracks or leaks
EQBL30AS
leak test points
Gas bottle safety information Leak test procedure
INTBBQ600/300_Jun11.indd 12 30/06/11 11:52 AM
electrolux integrated bbq 600/300mm installation 13
Installation warnings Installation instructions
warning
• This appliance shall only be used in an above ground,
open air situation with natural ventilation without
stagnant areas, where gas leakage and products of
combustion are rapidly dispersed by wind or natural
convection. This barbecue has been designed for
outdoor use only. Refer to diagrams below.
• Never install this barbecue inside any building,
garage, shed or breezeway or inside a boat, caravan
or recreational vehicle. This is to prevent the possibility
of fire, carbon monoxide poisoning or asphyxiation.
• Any enclosure in which this appliance is installed
shall comply with one of the following:
– An enclosure with walls on all sides, but at least one
permanent opening at the ground level and
no overhead covering.
– Within a partial enclosure that includes an overhead
cover and no more than 2 walls.
– Within a partial enclosure that includes an overhead
cover and more than 2 walls, the following shall apply:
– at least 25% of the total wall area is completely open
and at least 30% of the remaining wall area is open
and unrestricted.
• In the case of balconies, at least 20% of the total of
the side, back and front wall areas shall be and remain
open and unrestricted.
Outdoor area example 1
Outdoor area example 2
Outdoor area example 3
Outdoor area example 4
Outdoor area example 5
Choosing a location
• This appliance must not be installed on any combustible
material. A minimum clearance from any combustible
material is 450mm.
• The vertical clearance above the cooking surface to
any combustible materials must be at least 600mm.
• This appliance must be installed in accordance with
Australian Standards AS4557 and AS5601 and in
accordance with the local authority.
• When using LPG in an enclosure ventilation must be
provided. Gas is highly explosive and can cause serious
injury and damage to property if allowed to accumulate
and then be ignited.
• This barbecue is intended to be built into a benchtop
with a minimum depth of 600mm.
• Avoid windy positions as this will affect cooking
performance and burner efficiency. If this situation
cannot be avoided some shielding may be necessary.
• If the chosen location is exposed to rain consideration
will need to be given for water drainage. Some of the
rain can drain through the benchtop hole and through
the product.
The mounting enclosure
• The barbecue requires a non-combustible barrier under
the barbecue to prevent excessive temperatures being
accessed. The barrier panel is to be placed 30mm
under the base of the unit. There are spacers added to
the bottom of the unit to prevent barrier panel being too
close to barbecue base. Refer to diagram next page.
• The mounting enclosure must be constructed from
non-combustible materials. Suitable materials for
construction include masonry, granite, marble,
Hardiplank
®
, Villaboard
®
, over a metal frame or tiles.
• This appliance requires venting in the enclosure, see
diagrams for details.
• This appliance can be mounted either in an island type
bench or a bench with a splashback. Please read the
specific requirements for each mounting situation.
• For ULPG use, cabinetry below the barbecue must
have low level ventilation to prevent the possibility of
ULPG accumulating.
Island style installation
• If the appliance is installed in an island mount, it can be
centrally positioned. Special attention should be given
to the overall size of the island top to consider the hood
open and overhang.
• The cut-out size required for models EQBH60AS &
EQBL60AS is 735mm x 502mm.
• The cut-out size required for model EQBL30AS is
440mm x 502mm (as shown on page 15).
both ends
open
open side at
least 25% of
total wall area
30% or more in total of
the remaining wall area
is open and unrestricted
open side at
least 25% of
total wall area
30% or more in total of
the remaining wall area
is open and unrestricted
INTBBQ600/300_Jun11.indd 13 30/06/11 11:52 AM
14 installation electrolux integrated bbq 600/300mm
bench width 600 min
539
464
202
42
590
538
464
202 212
warning
• This appliance requires venting. An open area as
indicated below must be allowed for. A suitable grille
can be fitted if desired. This vent area is to allow air
into the enclosure for the correct combustion of gases
and for the correct exhausting of the products of
combustion. This vent must be 600mm x 25mm for
models EQBH60AS & EQBL60AS, and 300mm x 25mm
for model EQBL30AS. See location options on pg16.
Installing in a bench with a splashback
• The splashback must be made from a
non-combustible material.
• In the case of mounting this appliance against a wall
or fence it is imperative that care is taken to ensure
the isolation of combustible materials. All combustible
materials must be kept 450mm away from the barbecue.
• For roasting hood model there is a specic minimum
clearance required at the back of the barbecue between
the splashback and the bench cut-out of 73mm.
This is to allow clearance to open.
73 min to bench cut out
547
73 min to bench cut out
603
INTBBQ600/300_Jun11.indd 14 30/06/11 11:53 AM
electrolux integrated bbq 600/300mm installation 15
80 min
INTBBQ600/300_Jun11.indd 15 30/06/11 11:53 AM
16 installation electrolux integrated bbq 600/300mm
Venting options
There are two venting options that can be used. The first is
in the front of enclosure (see diagram below for requirements).
The second is in the barrier panel below the barbecue.
If an LPG bottle is to be stored under the barbecue,
it must be isolated from the vent in the barrier panel.
Front vent option – to be located centrally to burner box
EQBL30AS
EQBH60AS & EQBL60AS
25
135
600
300
Base vent option (enclosure front removed for clarity) – to be located centrally to burner box
EQBL30AS
EQBH60AS & EQBL60AS
25
65
600
300
INTBBQ600/300_Jun11.indd 16 30/06/11 11:53 AM
electrolux integrated bbq 600/300mm gas requirements & fitting 17
Gas requirements
Natural Gas requirements
• The enclosure must be constructed so that access
can be gained to the Natural Gas regulator at all times.
• For Natural Gas the gas supply is required to be
connected to 1.2m flexible hose supplied and therefore
must be located within this distance.
• The exible hose has a quick connect gas coupling.
The corresponding mating fitting will be required at
the gas supply end.
• For pipe sizing requirements for supply pipe refer
to AS5601.
Universal LPG Requirements
warning
• If an LPG bottle is to be stored in the enclosure under
the barbecue unit, it must be isolated from the barbecue
unit with a non-combustible panel.
The enclosure must comply with the requirements
of AS5601.
• AS5601 ventilation requirements for cylinder storage are:
Where of sheet metal or similar impervious construction
there shall be ventilation openings at the top and bottom
of the enclosure or recess, each opening providing a
free area of at least 200cm2 for every cylinder enclosed.
• For ULPG installations having enclosed cabinetry below
the separation panel that does not contain a gas bottle,
low level venting must be installed. This is to allow the
gas which is heavier than air escape from the enclosure
in the situation where there may be a leak. A minimum
opening of 200cm
2
is required.
Setting up the barbecue
Setting up the barbecue in mounting enclosure
• A match holder with attached chain has been included
with the instruction manual. This is provided for manual
ignition in the event the automatic ignition does not work.
The free end of chain is required to be permanently fixed
to the installation in a location that enables the match
holder to reach each burner (refer to page 18 for manual
lighting instructions).
• After the enclosure has been constructed as described
on page 13, position the assembled barbecue into the
cut-out hole.
• Check that the barbecue is level and is rmly supported.
• Connect to gas supply (Universal LPG or Natural Gas)
and leak test.
• For tment of the slimline lid or roasting hood (see right).
Fitting the slimline lid or roasting hood
Fitting of slimline lid
• Unpack the slimline lid.
• Remove side screws from barbecue trim surround
using a philips head screw driver.
• Cooking plates should be removed in order to attach
hinge bracket.
• Fit brackets to trim surround with the same screws.
• Fit lid to brackets.
Fitting of roasting hood
• Unpack the roasting hood.
• Remove side and rear screws from barbecue trim
surround using a philips head screw driver.
• Cooking plates should be removed in order to attach
hinge bracket.
warning
Due to the size of the roasting hood, it is recommended
that two people place the roasting hood into position.
• When tting roasting hood assembly, take particular
care to avoid scratching of the external trim.
• Once in position, x hood assembly to trim surround
with same screws.
INTBBQ600/300_Jun11.indd 17 30/06/11 11:53 AM
18 options & operating instructions electrolux integrated bbq 600/300mm
Operating instructionsOptions for configuration of hotplates
and grills
Before lighting the barbecue:
• Check that all hoses and gas ttings are tight.
• Open the roasting hood or slimline lid.
NOTE:
The slimline lid is designed as a cover for weather protection.
The lid is not designed to be used as a cooking hood.
• Check all control knobs are in the ‘OFF’ position.
• Ensure that the cooking surfaces are clean.
• Turn the gas isolation valve ‘ON’.
Lighting instructions
• Do not attempt to light burners with cooking
surfaces covered.
• Read instructions before lighting.
• To light a burner, depress the knob and rotate to
‘HIGH HEAT’. A spark is generated to light the flame
thrower alongside the burner. The flame thrower makes
an audible noise and only operates when the knob is
depressed to light burner. Release the knob and check
if the burner is alight, note that the audible noise from
the flame thrower will stop when the knob is released.
• If the burner did not light, turn the knob to the ‘OFF’ position.
Allow gas to disperse, then repeat lighting procedure.
Manual lighting
• If, in the event of the automatic ignition system not
working, the barbecue can be lit manually.
• To light manually, t a 40mm match to match holder
provided. Pass lit match through viewing slots below the
front of cooking plates down towards the burner, then
rotate the knob to HIGH HEAT to ignite. If ignition fails,
turn the control valve off and allow several minutes for
the gas to disperse before attempting to light again.
• Once alight, repeat for other burners as required.
pass match holder
through viewing slot at
front under cooking plates
Preheating
• This barbecue is tted with high power burners. In most
conditions it will only be necessary to preheat the barbecue
for 5 minutes before cooking can commence.
• As with most things, experience will familiarise you with the
effectiveness of and the time required to achieve the desired
preheating time to obtain the desired cooking temperature.
• Testing has shown that the burners can be turned
to low position for satisfactory cooking.
• If the unit does not operate correctly refer to the
troubleshooting section on page 21.
For EQBH60AS & EQBL60AS the grills and hot plate can
be positioned as desired.
For roasting (EQBH60AS only) it is recommended to place
the hotplate in the middle and a grill plate each side.
warning
Ensure flame tamers are positioned under grill panels.
Alternative arrangement when not roasting
INTBBQ600/300_Jun11.indd 18 30/06/11 11:53 AM
electrolux integrated bbq 600/300mm usage & lid safety leg 19
• If the burners are left to run too hot there will be excessive
smoking during the cooking process and subsequent
burning of the food being prepared. This may also result
in excessive flaring of the fat being emitted from the food.
• Roasting with the hood closed only requires the 2
outermost burners on low setting for satisfactory cooking.
Refer below for further information on roasting.
To turn the burner off
• When cooking is complete, rotate the knob fully clockwise
so the pointer on the knob is positioned at the ‘OFF’ position.
• Turn gas bottle isolation valve off after turning all knobs
to ‘OFF’ position when appliance not in use.
Using the roasting hood
Cooking with the hood closed only requires 2 burners to be
on low setting. The setting is to be adjusted depending on
conditions and using the temperature indicator as a guide.
• It is recommended when roasting to place the solid
hot plate in the centre with one grill on each side of
the plate. Use the two outer burners under the grills.
• To achieve even cooking of the food, place the food
onto a wire rack above the hot plate to allow air to
circulate under the food.
• Food can also be placed on the warming racks for
cooking with hood closed
warning
• Do not use more than 2 burners when the hood is
closed and do not allow the temperature to exceed
the ‘Ready’ zone of the temperature indicator. These
conditions create excessive heat and may cause
damage to the barbecue and roasting hood.
• When cooking with the hood closed the hot ue
gases flow out the rear of the appliance between
the splashguard and the hood. Ensure the barbecue
is suitably located to avoid damage or injury.
Lid safety leg – slimline lid only
To ensure that the user remembers to turn off the gas
before closing the lid, a pivoting safety leg has been fitted
(both small and large lids).
pivoting safety leg
When closing the lid the safety leg will pivot forward and
rest against the trim surface to prevent the lid closing.
After ensuring the gas has been turned off, the lid can be
fully closed by rotating the leg backwards.
pivoting safety leg
warning
THE SLIMLINE LID MUST NOT BE CLOSED WHEN THE
BURNERS ARE OPERATING.
Closing the lid during burner operation can cause
discolouration and damage to the lid and barbecue unit.
INTBBQ600/300_Jun11.indd 19 30/06/11 11:53 AM
20 cleaning and care electrolux integrated bbq 600/300mm
Cleaning and care
This Electrolux barbecue has been constructed from select
grade stainless steel which, if not cared for, may discolour
over time. To keep your barbecue looking its best we
recommend that the cooking surfaces are cleaned after
every use.
warning
Please ensure that your barbecue is switched off and
has cooled down before following the instructions below.
Cast iron plates and plate surround cleaning
The cooking plates and grills have a porcelain enamelled
coating and must be at ambient temperature before cleaning.
NOTE:
Many food acids, juices, marinades and sauces contain
highly acidic elements that will slowly attack the surface
of the cast iron if not removed immediately after cooking.
After use remove all solid material from the cooking surface
using a brass bristled barbecue brush or plastic bristled
scourer. Wipe off the remaining grease with paper towelling.
Gently wash the surfaces with a cloth or sponge and a mild
detergent and hot water. Dry components immediately and
coat the cooking surface with a light layer of cooking oil.
This protects the surface when not in use. Do not clean
the cooking surface in a dishwasher
Cleaning stainless steel surfaces
caution
Do not use abrasive or caustic cleaners, scourers or
metal scrapers on stainless steel surfaces as they may
permanently scratch and damage your barbecue.
• Wash all stainless steel components, including the
slimline lid, the roasting hood, tubular frame and control
knobs with a soft dishcloth using hot soapy water
• The barbecue interior can be wiped down with a soft
cloth in hot soapy water. The rear panel of the interior
is removable for easy cleaning
• Ensure that all surfaces are dried with a clean dry cloth
tips and information
Sometimes stainless steel surfaces are affected by a brown
discolouration called tea staining. This usually occurs in
areas which use high heat and can be removed using
specialised stainless steel cleaners. For best results, we
recommend that specialised cleaners be used regularly on
all stainless steel components. You will find these cleaners
at Electrolux spare parts outlets.
caution
Take extra care (particularly when cleaning on and around
the control knobs) to ensure that water and soapy residue
do not enter the control panel.
Care should also be taken not to disturb the spark electrode.
Cleaning the oil reservoirs
The electrolux integrated bbq 600/300mm has a unique oil
management system which uses overlapping channels to
drain all oil to the front into easily removed reservoirs and
should be cleaned after each use.
• To remove reservoirs, pull upwards from the front of the
barbecue and dispose of the contents of the catchment
responsibly. Rinse oil reservoirs in warm soapy water.
The reservoirs can be placed in the dishwasher if desired.
tips and information
The stainless steel panels may distort while in use but will
return to normal when cold.
INTBBQ600/300_Jun11.indd 20 30/06/11 11:53 AM
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/