Zonet ZVC7611 User manual

Copyright Statement

is the registered trademark of Zonet Technology Inc. All the products and

product names mentioned herein are the trademarks or registered trademarks of their

respective holders. Copyright of the whole product as integration, including its

accessories and software, belongs to Zonet Technology Inc. Without the permission of

Zonet Technology Inc., any individual or party is not allowed to copy, plagiarize, imitate

or translate it into other languages.

Table of Contents

1. Introduction ................................................................................................1

2. Package Content..........................................................................................1

3. System Requirement....................................................................................2

4. Hardware Installation ...................................................................................2

4.1 LED and Focusing ................................................................................2

4.2 Know your ZVC7611/ZVC7611W ...........................................................3

4.3 Connecting ZVC7611/ZVC7611W to Your Network ...................................4

4.4 ZVC7611/ZVC7611W Application Example ..............................................5

5. Software Installation ....................................................................................6

6. Using the Administrator Utility..................................................................... 11

6.1 General Setting ................................................................................. 12

6.1.1 LAN Setting ............................................................................... 14

6.1.2 Security..................................................................................... 15

7. Using the Viewer Utility .............................................................................. 16

7.1 Configure IP Camera Viewer ............................................................... 18

7.1.1 Configure Cameras ..................................................................... 18

7.1.1.1 Camera ........................................................................ 19

7.1.1.2 Schedule Recording ....................................................... 21

7.1.1.3 Audio ........................................................................... 23

7.1.1.4 Motion Record ............................................................... 24

7.1.2 General Settings......................................................................... 25

7.1.2.1 General ........................................................................ 25

7.1.2.2 E-Mail Setting ............................................................... 26

7.1.2.3 Security ....................................................................... 27

7.1.2.4 About........................................................................... 28

7.3 Full-screen mode............................................................................... 32

7.4 Scan ................................................................................................ 33

7.5 Zoom-in / Zoom-out .......................................................................... 34

7.6 PTZ.................................................................................................. 35

7.7 Snapshot.......................................................................................... 36

7.8 Recording ......................................................................................... 37

7.9 Video Playback .................................................................................. 38

8. Web Connection and Setup ......................................................................... 39

8.1 Camera ............................................................................................ 40

8.2 LAN ................................................................................................. 41

8.3 WLAN (For ZVC7611W) ...................................................................... 43

8.4 E-Mail and FTP .................................................................................. 45

8.5 Motion Detection ............................................................................... 46

8.6 System............................................................................................. 47

8.7 Status .............................................................................................. 48

8.8 Users ............................................................................................... 48

8.9 Log .................................................................................................. 49

9. Specifications ............................................................................................ 50

10. Frequently Asked Questions ........................................................................ 51

Appendix A Viewing via UPnP in Windows XP ....................................................... 52

Appendix B Configure Windows 2003 Server ....................................................... 55

1

1. Introduction

Thank you for choosing Zonet ZVC7611/ZVC7611W. ZVC7611/ZVC7611W sends live

video through 10/100Mbps wired network to a web browser or camera viewer across

Internet anywhere in the world! This compact, self-contained unit lets you keep an eye

on your home, your kids, and your workplace—whatever’s important to you.

How does the Camera do all of this? Unlike standard “web cams” that require an attached

PC, ZVC7611/ZVC7611W can connect directly to a network. The MJPEG video

compression produces a high quality, high-frame rate, 640 x 480 video stream. The

included Camera Viewer utility lets you record the video to your local hard drive, “live” or

on a predetermined schedule.

Use the instructions in this User Manual to help you integrate ZVC7611/ZVC7611W into

your network. These instructions should be all you need to get the most out of

ZVC7611/ZVC7611W.

2. Package Content



One ZVC7611/ZVC7611W



One Quick Installation Guide



One Installation CD w/Manual



One Power Adapter



One Camera Stand



One Ethernet Cable



One Antenna (ZVC7611W Only)

Contact your local authorized reseller or the store purchased from for any items

damaged and/or missing.

2

3. System Requirement



LAN: 10/100Mbps Fast Ethernet



WLAN: IEEE 802.11b/g



OS System: Windows 2000/XP/Server 2003/Vista/7



IE Version: 6.0.29 or above



CPU: Intel Pentium III 750MHz above or Intel Celeron 1GHz above



Memory Size: 128MB (256MB recommended)



DirectX 9.0 or above



VGA card with fully DirectX 9.0 supported.



VGA Card Resolution: 800 x 600 or above

4. Hardware Installation

4.1 LED and Focusing

The Camera head and its focus ring allow you to modify the aim and focus of

ZVC7611/ZVC7611W.

To adjust ZVC7611/ZVC7611W’s focus, rotate the focus ring.

LED Indicator Status Description

ON Indicates LAN port is connected

LAN

Flashing

Indicates LAN activity

(transferring or receiving data)

ON Indicates WLAN is connected

WLAN

(ZVC7611W only)

Flashing

Indicates WLAN activity

(transferring or receiving data)

POWER ON Indicates camera is receiving power

3

4.2 Know your ZVC7611/ZVC7611W

Front View

Bottom View

Reset Button

LAN Port

Power Jack

Focus Ring

LED Green:

LAN Activity

LED Orange:

WLAN Activity

(ZVC7611W Only)

LED Blue:

Power On

Wireless SMA Connector

(ZVC7611W Only)

4

Port & Button Description

Power Jack Where you can connect the power adapter

LAN Port Where you can connect the RJ-45 Ethernet cable

Antenna Connector

(ZVC7611W Only)

This is standard Reverse SMA connector where any

antenna with Reverse SMA connector can connect to

ZVC7611W

Reset Button

1.

If problems occur with your ZVC7611/ZVC7611W,

press the reset button with a pencil tip for less than 2

seconds and the camera will re-boot itself, keeping your

original configurations.

2.

If problems persist or you experience extreme

problems or you forgot your password, press the reset

button for longer than 5 seconds and the camera will

reset itself to the factory default settings

Note: your original configurations will be replaced with

the factory default settings.

4.3 Connecting ZVC7611/ZVC7611W to Your Network

1. Connect ZVC7611/ZVC7611W to

your network by provided RJ-45

Ethernet cable from the

switch/router to the LAN port of

ZVC7611/ZVC7611W.

2. Connect the power adapter to

the ZVC7611/ZVC7611W and

plug the power adapter to power

socket. ZVC7611/ZVC7611W will

be powered on. When the

ZVC7611/ZVC7611W is ready,

the POWER LED will steady blue.

5

3. You have to connect the Wireless

Antenna to ZVC7611W if you’d

like to use it in a wireless network

environment.

4. Make sure that you have

installed correct VGA driver and

DirectX 9.0 or above.

4.4 ZVC7611/ZVC7611W Application Example

The following diagram explains one of the most typical applications for the

ZVC7611/ZVC7611W.

6

5. Software Installation

NOTE:

Snap-shot screens of the following installation procedure are based on Windows

XP. Installation procedures will be similar for other windows operating systems.

1.

Insert Installation CD to

your CD-ROM drive

and the

Welcome screen appears. If

you don’t see the Welcome

screen, b

rowse CD and

double-click

Autorun.exe

.

2. The Wizard will show four

selections, select the

program you want to install

or click Exit to install later.

7

3.

Click Next to continue the

installation

4.

If you want to change the

path, click Change;

otherwise just click Next to

continue.

5.

Click Install to start

installing the program

8

6.

Click Finish to complete

Administrator Utility

installation.

7.

Go back to wizard page and

click Install 16 Chan

camera viewer, the system

will start running viewer

installation.

8.

Administrator Utility will

run automatically after

viewer installation. In first

page, the cameras found in

the network are listed.

Choose one you want to

configure and click

Configure Camera to

continue.

9

9.

Enter default password

1234 and click OK to login

IP setup page.

10.

The program will detect IP

address status of your

network automatically. You

can accept the suggested

value or enter the value

manually. If you enter the

value manually, please be

aware that Subnet Mask

must be the same for both

camera and PC. Click OK to

apply the configuration.

11.

Click IPCam Surveillance

Software icon from

desktop/ quick launch bar/

start menu to start the IP

camera surveillance

software.

10

12.

C

lick System configure

button and a popup

menu will appear. Select

Configure Cameras to

configure

ZVC7611/ZVC7611W.

13.

C

hoose the camera you

want to connect in Camera

Search list and click Select

to add it into the channel you

want to view then click ok

14.

IP Camera Viewer will pop

out and the video will show

on the channel you choose

automatically.

Congratulations! You’ve successfully configured your ZVC7611/ZVC7611W!

11

6. Using the Administrator Utility

IPCam Admin Utility allows users to search and setup ZVC7611/ZVC7611W located

within Intranet or Internet. From the utility, users can view all the information of the

selected camera; furthermore, it provides a setting wizard, which can guide users to add

ZVC7611/ZVC7611W to the network easily and promptly.

There are two ways to run IPCam Admin Utility as follows.

1. Click Start select Programs\IP Camera\Admin Utility to run the utility.

2. Double click IPCam Admin Utility icon to run the utility.

12

6.1 General Setting

Information of Camera

Camera Information It displays MAC address, IP Address, Camera Name and

Model of the selected camera.

Task Bar

Search Camera

Click Search Camera to search cameras on the network.

Browse Camera via Web

Click Browse Camera via Web to

activate browser and

auto connect to IP cam to get video

Configure Camera

Click Configure camera to

change the IP setting and

user name password of the IP Cam you selected.

Languages

Language Supports 3 languages (English/Japanese/Chinese).

13

When you click Configure Camera icon , a screen will pop up to enter User Name

and Password. The default value is as follows.

User Name: Admin

Password: 1234

14

6.1.1 LAN Setting



IP Address: Enter an IP Address within the IP address range on your LAN. Default

IP Address: http://192.168.2.3



NetMask: Subnet Mask field must match the subnet setting on your LAN.



Gateway: Gateway setting must be the same with the gateway used by the PCs on

your LAN.



DNS: DNS Server (Domain Name Server) translates names to IP addresses. Set the

same DNS Server as the PCs on your LAN.



Web Port: Default web port is 80. If you change the web port from 80 to 8080, you

must type http://192.168.2.3:8080 to connect ZVC7611/ZVC7611W through web

browser.

15

6.1.2 Security



Camera Name: The default camera name is IP Camera/Wireless IP Camera.



New Password: Enter the new password you want to use for ZVC7611/ZVC7611W.



Confirm Password: Retype the new password to confirm the setting.

16

7. Using the Viewer Utility

Before you start:

IPCam Surveillance Software will only work when monitor’s resolution is 1024 x 768.

Please must change the resolution before using IPCam Surveillance Software.

You can click IPCam Surveillance Software icon from desktop/ quick launch

bar/ start menu to start IPCam Surveillance software.

IP Camera Viewer Introduction:

You can also put the mouse cursor on a certain figure to see the button name.

Language

Display

layout

Full screen /

Scan

Zoom Out /

Zoom In

PTZ Control /

Home

Recording / System configure

Playback / Snap shot

Close window (stop

surveillance) / Minimize window

Video displaying area

Message display

box

Page is loading ...

Zonet ZVC7611 User manual

This manual is also suitable for

Zonet ZVC7611 User manual

Related papers

Other documents