Zonet ZVC7610W Quick Installation Manual

Zonet
Brand
Zonet
Model
ZVC7610W
Category
WLAN access points
Type
Quick Installation Manual

This manual is also suitable for

- 1 -
1 Getting Started
Package Contents
One ZVC7610 or ZVC7610W
One AC Power Adapter
One Camera Stand
One RJ-45 Ethernet Cable
One Installation CD w/ User Manual
One Quick Installation Guide
One Wireless Antenna (ZVC7610W only)
System Requirement
Networking
LAN: 10Base-T Ethernet 100Base-TX Fast Ethernet.
WLAN: IEEE 802.11b/g (ZVC7610W only)
Accessing the Camera using Web Browser
Platform: Windows 2000/XP/Vista, Macintosh OSX
CPU: Intel Pentium III 800MHz or above
RAM: 512MB
Resolution: 800x600 or above
User Interface: Internet Explorer 6.0 or above, Mozilla Firefox 2.00 or above,
Apple Safari 2 or above
- 2 -
2 Setting Up the Camera
Installing the Camera Stand
ZVC7610/ZVC7610W comes with a Camera Stand. It uses a swivel ball screw
head to lock to the camera’s screw holes. Attach the Camera Stand and you
can place the unit anywhere by mounting the camera through the three screw
holes which located at the bottom of the Camera Stand.
The Camera Stand
Connect ZVC7610 to your Network (LAN)
Use the provided RJ-45 Ethernet cable to connect the ZVC7610 to your local
area network (LAN).
ZVC7610 will power ON automatically after the AC Power Adapter is connected.
You may also verify the power status from the Power LED on the front panel.
The Link LED will start flashing in green light. ZVC7610 will be on standby
mode and it is ready to use.
- 3 -
Connect ZVC7610W to your Wireless Network (WLAN)
You have to connect the Wireless Antenna to the ZVC7610W if you’d like to use
it in a wireless network environment.
ZVC7610W will start searching any available wireless networks around it after
it is power ON.
NOTE: If the ZVC7610W cannot connect to your wireless network (WLAN), you’ll
have to configure the wireless settings through your network by using the
RJ-45 Ethernet Cable.
Connecting the RJ
-
45 Ethernet Cable
Connecting the
Wireless Antenna
- 4 -
3
Accessing the
ZVC7610/ZVC7610W
Using IP Finder
1. Insert the Installation CD into your computer’s CD-ROM drive and initiate
the Auto-Run program.
2. Click IP Finder and the utility will launch automatically. The following
control panel will appear on your screen.
3. You may use your web browser or Ultra View to access the configuration
after you obtained the IP address of the connected ZVC7610/ZVC7610W.
TIP: To install IP Finder, you have to use the Installation CD and
install the IP Finder setup program to your computer first.
Display all connected
ZVC7610/ZVC7610W
Search
t
o find the IP address of the connected camera(s)
Click Change IP to modify the IP address of the selected camera
Click Exit to close the utility
- 5 -
Configuration of ZVC7610/ZVC7610W
1. Open your web browser of your computer, for example: Microsoft Internet
Explorer
2. Enter the IP address on the address bar and press Enter
Default IP Address: 192.168.0.30
3. The following login window will appear. Enter the username and password
to login and access the web configuration of the camera.
Default username: admin (all lowercases)
Default password: admin (all lowercases)
Enter the IP address here.
Enter Username and Password to login
- 6 -
4. Click Setup and Smart Wizard to set up your ZVC7610/ZVC7610W quickly.
The Smart Wizard will guide you through the necessary settings with
detailed instructions of each step.
For more information of web configuration or Ultra View, please refer to the
User Manual in the provided Installation CD.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Zonet ZVC7610W Quick Installation Manual

Zonet
Brand
Zonet
Model
ZVC7610W
Category
WLAN access points
Type
Quick Installation Manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents