Zonet ZEN3200 Installation guide

Zonet
Brand
Zonet
Model
ZEN3200
Category
Interface cards/adapters
Type
Installation guide

This manual is also suitable for

Zonet ZEN3200-08 is an Ethernet adapter that provides connectivity to a network. It supports 10/100Mbps Fast Ethernet speeds and full-duplex mode, which can increase channel bandwidth up to 200Mbps when connected through an Ethernet switching hub. The adapter includes a complete set of drivers for popular network operating systems and an optional BOOT ROM device that allows diskless workstations to be connected to the network. With its ease of installation and configuration, the Zonet ZEN3200-08 is an excellent choice for enhancing network connectivity and improving data transfer speeds.

Zonet ZEN3200-08 is an Ethernet adapter that provides connectivity to a network. It supports 10/100Mbps Fast Ethernet speeds and full-duplex mode, which can increase channel bandwidth up to 200Mbps when connected through an Ethernet switching hub. The adapter includes a complete set of drivers for popular network operating systems and an optional BOOT ROM device that allows diskless workstations to be connected to the network. With its ease of installation and configuration, the Zonet ZEN3200-08 is an excellent choice for enhancing network connectivity and improving data transfer speeds.

1
1
0
0
/
/
1
1
0
0
0
0
M
M
b
b
p
p
s
s
F
F
a
a
s
s
t
t
E
E
t
t
h
h
e
e
r
r
n
n
e
e
t
t
A
A
d
d
a
a
p
p
t
t
e
e
r
r
Q
Q
u
u
i
i
c
c
k
k
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
G
G
u
u
i
i
d
d
e
e
Introduction:
Congratulation on your purchase of the Zonet ZEN3200 10/100Mbps
Fast Ethernet Adapter. This adapter was designed and manufactured to
give you years of trouble free and reliable service.
The Zonet ZEN3200 supports full-duplex mode. Full duplex mode can
be used to obtain throughput up to 200Mbps when the twisted-pair port
connecting through an Ethernet switching hub. This feature not only
increases the channel bandwidth from 10M to 200Mbps but also avoids
the performance degrading problem due to the characteristic of the
Ethernet CSMA/CD protocol.
The ZEN3200 includes a complete set of drivers for popular network
operating systems. the optional BOOT ROM device allows the diskless
workstation to be connected to the network.
Packing List:
The adapter package should contain the following items:
1. One 32-bit PCI 10/100Mbps Fast Ethernet Adapter
2. User's guide this guide
3. One CD for Driver
If any of these items are missing, please contact your reseller
Installation:
Hardware Installation :
1.Turn OFF the computer, unplug the power cord and open the computer
case.
2.Pick a free PCI bus master expansion slot and remove the expansion
slot cover. Insert the adapter into the slot until it is fully seated. Secure
the adapter.
3.Replace the computer cover and connect the network cable to the
newly installed network adapter. Reconnect the computer's power cord
and plug it into the power outlet.
Configuration:
The Zonet ZEN3200 is automatically configured when you
power-on computer, In certain computer, however, you must modify BIOS
by entering CMOS ETUP utility to enable PCI Device and map INTA to
an appropriate address, Please refer to the system documentation for
details on configuration the PCI SYSTEM BIOS.
Driver Installation:
Before you connect adapter to the network, you have to install the
network driver first. The driver for each networking operating system is
under a separate directory. In the directory, there is a file describing
driver's installation procedure.
Boot ROM Installation:
The optional Boot ROM device allows you to connect a diskless
workstation to the network. Perform the following steps to install your
Boot ROM device:
1. Insert the Boot ROM into the socket on the adapter.
2. Refer to the installation procedure provided by networking operating
system (Options: Some adapters need to run SETUP Utility to enable
Boot ROM function)
12-086-00518 Rev:01
  • Page 1 1
  • Page 2 2

Zonet ZEN3200 Installation guide

Zonet
Brand
Zonet
Model
ZEN3200
Category
Interface cards/adapters
Type
Installation guide
This manual is also suitable for

Zonet ZEN3200-08 is an Ethernet adapter that provides connectivity to a network. It supports 10/100Mbps Fast Ethernet speeds and full-duplex mode, which can increase channel bandwidth up to 200Mbps when connected through an Ethernet switching hub. The adapter includes a complete set of drivers for popular network operating systems and an optional BOOT ROM device that allows diskless workstations to be connected to the network. With its ease of installation and configuration, the Zonet ZEN3200-08 is an excellent choice for enhancing network connectivity and improving data transfer speeds.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents