Aleratec 330115 330115EU User guide

Category
Media duplicators
Type
User guide

This manual is also suitable for

SOFTWARE USER GUIDE
Aleratec
USB Duplication Suite
1:10 USB 3.0 Copy
Cruiser Mini™
Part No. 330113, 330113EU
1:16 USB 3.0 Copy
Cruiser Mini™
Part No. 330115, 330115EU
1:22 USB Copy
Cruiser Mini™
Part No. 330119, 330119AU,
330119EU
www.aleratec.com
Copyright/Model Identication
The content of this manual is for informational purposes only and is subject
to change without notice.
This manual is copyrighted with all rights reserved. Under copyright laws,
this manual and the software described within may not be copied, except in
the normal use of the product(s) described within or to make a backup copy.
Copyright© 2014
Aleratec, Inc.
9851 Owensmouth Avenue
Chatsworth, CA 91311 U.S.A.
www.aleratec.com
Aleratec
is a registered trademark and 1:22 USB Copy Cruiser Mini™, 1:16
USB 3.0 Copy Cruiser Mini™, and 1:10 USB 3.0 Copy Cruiser Mini™ are
trademark of Aleratec, Inc.
Check out Aleratec Online!
• google.com/+AleratecInc
• YouTube.com/Aleratec
• Twitter.com/Aleratec
• Facebook.com/Aleratec
• Blog.Aleratec.com
Please record the following information to help expedite any warranty claim:
Model No. _____________________ Serial No. _____________________
Date Purchased ________________________________________________
Place of Purchase ______________________________________________
www.aleratec.com
Table of Contents
Introduction .......................................................................................1
Initial System Setup ................................................................................1
For Ease of Use .......................................................................................2
Using the USB Duplication Suite Software ....................................5
Source Tab ..............................................................................................6
Destination Tab .......................................................................................7
Data Copy Only ......................................................................................9
Format (FAT, FAT32, NTFS) ................................................................10
Format Then Data Copy (FAT, FAT32, NTFS) .....................................12
Create Image File ..................................................................................15
Clone Image File ...................................................................................16
Port Training .........................................................................................17
Technical Support ..........................................................................19
Technical Support FAX Back Form ..............................................20
www.aleratec.com
www.aleratec.com
1
Introduction
Thank you for purchasing an Aleratec USB Duplicator. Please read this
Software User Guide thoroughly before using this product.
Initial System Setup
1. Connect the USB cable (included) to the USB port on the back of your
duplicator and to an empty USB port on your computer.
2. Connect the included power cord to the power input on the duplicator
and into an available power outlet.
3. Insert the Aleratec USB Duplication Suite Installation and Software
Flash Drive into an available USB port on your computer.
4. Click on Install Aleratec USB Duplication Suite to install the
duplication software.
5. Follow the on-screen prompts to complete the installation.
6. Press the power button to power up the Aleratec USB Duplicator.
7. The blue power LED will light, and the computer will recognize the
device.
8. Start the USB Duplication Suite duplication software via the icon
on your Desktop or in the Start menu under “All Programs.”
www.aleratec.com
2
Introduction
For Ease of Use
To make duplication even easier, we’ve added a feature that lets you match
up the logical drives shown in the USB Duplication Suite software with the
actual physical port position of that drive. To take advantage of this function,
a “Port Training” needs to be performed to match each USB Port to your
Aleratec USB Duplicator. For example, you would likely designate the upper
port on the duplicator Port 1 and so on (see image).
1:22 USB Copy
Cruiser Mini™
For details please see
section titled Port Training
on page 17 in the manual.
www.aleratec.com
3
Introduction
For Ease of Use
1:16 USB 3.0 Copy Cruiser Mini™
For details please see section
titled Port Training on page 17
in the manual.
www.aleratec.com
4
Introduction
For Ease of Use
1:10 USB 3.0 Copy Cruiser Mini™
For details please see section
titled Port Training on page 17
in the manual.
www.aleratec.com
5
Using the USB Duplication Suite Software
Main Menu
The USB Duplication Suite’s main menu offers eight functions:
1. Data Copy Only
2. Format FAT
3. Format FAT32
4. Format NTFS
5. Format Then Data Copy
6. Create Image File
7. Clone Image File
8. Port Training
Choose the desired option from the drop down menu located on the Source tab.
When using the USB Duplication Suite, ensure that only the USB ash
drives you wish to operate on are plugged into the duplicator. Remove
all other media from the computer and duplicator before using the USB
Duplication Suite.
www.aleratec.com
6
Using the USB Duplication Suite Software
Source Tab
The Source tab has several key functions as listed below.
1. Job Selection List: This drop down menu lists all the available
functions the USB Duplication Suite offers.
2. Add File / Add Folder: Add File/Add Folder buttons allows you to
select any les / folders you would like to copy. These buttons are
available for Data Copy Only or Format Then Data Copy job types.
3. Remove / Clear: The Remove button allows you to remove items listed
in the Add Files box one at a time. The clear button will remove all
items listed in the Add Files box.
4. Full Format: The Full Format check box allows you to specify whether
or not the format job being performed is a full format or a quick format.
Note: quick format is the default setting if Full Format is unchecked.
5. Verify Data: If you wish to verify the Source data les are copied
successfully, you may click the Verify Data check box when applicable.
3.
4.
5.
2.
1.
www.aleratec.com
7
Using the USB Duplication Suite Software
Destination Tab
1. Drive List: The drive list will list all drives that are recognized by the
computer. Each drive may be selected or deselected individually by
clicking on the check box next to the corresponding drive letter or USB
port number (See Port Training). The checked drives are the target
drives that will be operated on when the Start button is clicked. Select
the target drives carefully before pressing start.
The Select All button will select all available drives in the list.
The Deselect All button will deselect all drives in the list.
The Refresh button will refresh the drives list. This is necessary if
new drives have been added or removed from the device.
2. Enter Label: The Enter Label box allows you to specify a volume label
for the target drives during a format operation. This is available during
Format and Format Then Data Copy job types.
3. Drives: The drives box displays the number of drives that are being
operated on in the current round.
2.
1.
3.
www.aleratec.com
8
Using the USB Duplication Suite Software
Destination Tab
4. Rounds: The rounds box allows you to specify how many rounds of the
selected job type you would like to conduct.
5. Output Window: The output window displays job status updates while
jobs are running or when they have completed.
6. Completed: The Completed box displays the total number of drives
that have been completed for the current job. For jobs with more than
one round, the completed box will be updated after each round is
completed.
7. Rejected: The Rejected box displays the number of drives that have
been rejected due to errors during the copy or verify process.
8. Start Button: Clicking the Start button will initiate the job type that was
selected from the drop down menu in the Source tab.
9. Cancel Button: Clicking the Cancel button will stop the current job
from running.
10. Help Button: The Help button allows you to gain quick access to
relevant sections of the USB Duplication Suite User Guide.
4.
5.
10.
7.
6.
9.
8.
www.aleratec.com
9
Using the USB Duplication Suite Software
Data Copy Only
Use this function to copy les or folders to one or more USB ash drive(s).
This function will overwrite any les/folders on the target drive(s) with the
same name as the source les/folders.
1. Start by choosing Data Copy Only from the drop down menu located
on the “Source” tab.
2. On the “Source” tab, click “Add Files” to copy individual les or “Add
Folder” to copy an entire folder. You may add both les and folders.
3. Once all data has been selected, you may choose to verify the data copy
process by checking the “Verify Files” box located on the right of the
drop down menu.
4. Click on the Destination tab, select which drives you would like to
operate on from the drive list.
5. After selecting the drives from the drive list and specifying any options
you may click the Start button located inside the Destination tab to
begin the duplication process.
www.aleratec.com
10
Using the USB Duplication Suite Software
Format (FAT, FAT32, NTFS)
There are three format options available in the USB Duplication Suite.
Format FAT, Format FAT32, and Format NTFS. Each option will format the
selected drives and if specied apply a volume label.
By default a quick format will be run. However if you wish to perform a
full format, you must check the “Full Format” box after selecting one of the
three formats.
1. Start by selecting one of the three formats “Format FAT”, “Format
FAT32”, or “Format NTFS” from the drop down menu.
2. If a Full format is desired, check the box labeled Full Format to the
right of the drop down menu.
3. Next, click on the Destination tab.
4. Select the drives that you wish to format.
www.aleratec.com
11
Using the USB Duplication Suite Software
Format (FAT, FAT32, NTFS) - continued
5. You can specify a volume label which will be applied to all drives in
the text box under “Enter Label” which is found in the Destination tab.
I. Note: FAT and FAT32 le systems have restrictions on volume
labels which allow for up to 11 characters, not including the following
special characters * ? . , ; : / \ | + = < > [ ]
II. NTFS le systems allow up to 32 characters for a volume label and
allow special characters
6. Click on the Destination tab, select which drives you would like to
operate on from the drive list.
7. Specify the number of rounds you would like to conduct. (For multiple
rounds: when the rst round is nished you will be prompted to remove
completed drives and insert the new drives before pressing OK to
continue).
8. Press the Start button to start the format process. Check the Output
window for job status updates
NOTE: If Full Format is selected, the formatting process may
take a signicant amount of time.
www.aleratec.com
12
Using the USB Duplication Suite Software
Format Then Data Copy (FAT, FAT32, NTFS)
The Format Then Data Copy function allows you to perform both a format
and data copy in the same job process. All selected drives will be formatted
with the le system you selected. Once the format is complete, the data
copy process will start automatically.
There are three format options available in the USB Duplication Suite.
Format FAT, Format FAT32, and Format NTFS. Each option will format the
selected drives and if specied apply a volume label.
By default a quick format will be run. However if you wishes to perform a
full format, you must check the “Full Format” box after selecting one of the
three formats.
1. Start by selecting “Format Then Data Copyfrom the drop down menu.
www.aleratec.com
13
Using the USB Duplication Suite Software
Format Then Data Copy (FAT, FAT32, NTFS) - continued
2. A new window will appear. Here you must select one of the three
formats “Format FAT”, “Format FAT32”, or “Format NTFS” by
clicking on its associated radio button. Once the format selection has
been made, press OK.
3. If a Full format is desired, check the box labeled Full Format to the
right of the drop down menu.
4. Because a data copy is involved in this job function, you may also
select the “Verify Data” check box.
5. Next, you may add any les or folders for copying, by clicking the
“Add File” or “Add Folder” buttons.
6. Next, click on the Destination tab.
7. Select the drives that you wish to format.
8. You can specify a volume label which will be applied to all drives in
the text box under “Enter Label” which is found in the Destination tab.
I. Note: FAT and FAT32 le systems have restrictions on volume
labels which allow for up to 11 characters, not including the following
special characters * ? . , ; : / \ | + = < > [ ]
II. NTFS le systems allow up to 32 characters for a volume label and
allow special characters
9. Click on the Destination tab, select which drives you would like to
operate on from the drive list.
www.aleratec.com
14
Using the USB Duplication Suite Software
Format Then Data Copy (FAT, FAT32, NTFS) - continued
10. Specify the number of rounds you would like to conduct. (For multiple
rounds: when the rst round is nished you will be prompted to remove
completed drives and insert the new drives before pressing OK to
continue).
11. Press the Start button to start the format and data copy process. Check the
Output window for job status updates.
NOTE: If Full Format is selected, the formatting process may take a
signicant amount of time.
www.aleratec.com
15
Using the USB Duplication Suite Software
Create Image File
Use this function to create an image le from a single USB ash drive. The
create image le supports creating images of bootable media which may
then be copied using the Clone Image le job function.
1. From the drop down menu choose “Create Image File”. A new window
will open.
2. The drop down list will show all available drives. Select the drive you
would like to create an image of.
3. You may modify the le name of the image le that will be created by
editing the File Name eld. Make sure the le name has the extension
“.img”.
4. Once the correct drive is selected and the le name is specied. Press
Start to begin the process.
5. You can check the job status in the box located in the Create Image File
window.
NOTE: This process may take a signicant amount of time.
www.aleratec.com
16
Using the USB Duplication Suite Software
Clone Image File
Use this function to clone an image to one or more drives. The clone image
le supports cloning images of bootable media that have been created using
the “Create Image File” function of the USB Duplication Suite.
1. From the drop down menu choose “Clone Image File”. A new window
will open.
2. To select the image le that will be cloned. Click the “Browse” button
and select an .img le.
3. Next, select the drives that the image will be cloned to by checking the
appropriate drives in the drive list located on the window shown above.
4. Once all drives have been selected press the Start button.
5. You can check the job status in the box located under the “Browse”
button.
NOTE: This process may take a signicant amount of time.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25

Aleratec 330115 330115EU User guide

Category
Media duplicators
Type
User guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI