INSTALLATION GUIDE
Aleratec
Wall Mount for Charge and
Guard Secure Charge/Sync
Cabinet 16™
Part No. 400107
www.aleratec.com
Copyright/Model Identication
The content of this manual is for informational purposes only and is subject
to change without notice.
This manual is copyrighted with all rights reserved. Under copyright laws,
this manual and the software described within may not be copied, except in
the normal use of the product(s) described within or to make a backup copy.
Copyright© 2014
Aleratec, Inc.
9851 Owensmouth Avenue
Chatsworth, CA 91311 U.S.A.
www.aleratec.com
Aleratec
®
is a registered trademark and Charge and Guard Secure
Charge/Sync Cabinet 16™ is a trademark of Aleratec, Inc.
Check out Aleratec Online!
• google.com/+AleratecInc
• YouTube.com/Aleratec
• Twitter.com/Aleratec
• Facebook.com/Aleratec
• Blog.Aleratec.com
Please record the following information to help expedite any warranty
claim:
Model No. 400107
Date Purchased ________________________________________________
Place of Purchase ______________________________________________
www.aleratec.com
1
Introduction
Thank you for purchasing the Aleratec Wall Mount for Charge and Guard
Secure Charge/Sync Cabinet 16. Please read this Installation Guide
thoroughly before using this product.
Product Features
• Safely secures cabinet to the wall
• Preserves precious oor/table space
• Heavy-duty construction and materials
Included Items
Safety
WARNING: Make sure that you consult with appropriate engineering,
architectural or construction professional to ensure that your Aleratec
mounting solution is mounted properly to handle applied loads.
CAUTION: Make sure the wall mount bracket is level, ush and snug to
the wall surface. DO NOT OVERTIGHTEN THE BOLTS.
CAUTION:DONOTEXCEEDMAXIMUMLISTEDWEIGHT
CAPACITY.SERIOUSINJURYORPROPERTYDAMAGEMAY
OCCUR!
Bottom Bracket
Top Bracket
Paper Mounting Template
(2) Security Screws
Registration Card
Installation Guide (this document)
www.aleratec.com
2
Introduction
Tools Needed
You will also need mounting hardware such as bolts, screws, washers, etc to
mount the brackets and additional tools for the mounting hardware chosen.
Suggestions for different methods of mounting:
Brick wall:
5/16” x 3” Concrete anchor bolts
5/16” Washers
1/4” Concrete drill bit
Drywall:
1/4” x 3” Toggle bolts
1/4” Washers
3/4” Drill bit
Stud:
5/16” x 2.5” Lag screws
5/16” Washers
15/64” Drill bit
Please consult with an appropriate engineering, architectural or
construction professional to choose the appropriate mounting
hardware.
www.aleratec.com
3
Introduction
Mounting Considerations
Space Requirements:
www.aleratec.com
4
Introduction
Wood Stud Wall Mounting Option
Studs can be positioned in one of four mounting options. While the rst
option (studs on either side) is recommended, you should consult with a
construction professional to conrm which method is best suited for your
particular situation. After you decide on a hole option, follow attachment
instructions on the following pages.
Important – Wall brackets must be secured to the wall using all 6 mounting
holes using appropriate hardware for the wall surface. DO NOT mount to
drywall without at least one stud to support both brackets. For mounting
to a brick wall, consult with an appropriate engineering architectural or
construction professional.
Option 1
RECOMMENDED
Studs on either side
Option 2
One stud in the center
Option 4
One stud on the left side
Option 3
One stud on the right side
www.aleratec.com
5
Installation
Wood Stud Wall Mounting
1. Find stud and draw a mark.
2. Place template on wall lining up the chosen hole with the stud at the
desired height.
www.aleratec.com
6
Installation
Wood Stud Wall Mounting
- Continued
3. Secure template to wall and check to ensure it is level.
4. Use the appropriate drill bit(s) to drill the three holes for the top bracket
that correspond with the hole markers on the paper template.
www.aleratec.com
7
Installation
Wood Stud Wall Mounting
- Continued
5. U
se the appropriate drill bit(s) to drill the bottom three holes
.
6. Remove paper template from the wall.
www.aleratec.com
8
Installation
Wood Stud Wall Mounting
- Continued
7. Secure the top bracket with your chosen mounting hardware. Verify wall
bracket is level before tightening screws.
8. Repeat step 7 for the bottom bracket.
www.aleratec.com
9
Installation
Wood Stud Wall Mounting
- Continued
9. Hang the Charge and Guard Secure Charge/Sync Cabinet 16 unit onto the
brackets.
Warning:Two people are
required to lift the cabinet.
www.aleratec.com
10
Installation
Wood Stud Wall Mounting
- Continued
10. Unlock and open the top door of the cabinet.
11. Install the two security screws through the holes in the back of the cabinet
into the top wall bracket.
www.aleratec.com
11
Technical Support
After reading this Installation Guide, if you need additional assistance with
this product, please contact Aleratec Technical Support. Our technical staff
will be happy to assist you, but they may need your help to better assist you.
Calling Aleratec Technical Support without all the necessary information
can be both time consuming and frustrating. Therefore, please try to have
the following information ready before calling:
1. Part Number: 400107
2. Troubles - your questions about the Wall Mount for Charge and Guard
Secure Charge/Sync Cabinet 16. Please provide enough information
about your problems so our technical staff can recreate and diagnose it.
Technical Support Addresses and Phone Numbers
X By e-mail: [email protected] – Skype: support.aleratec.com
X By Telephone: 1-818-678-0484 – FAX at: 1-818-678-0483
Technical Support Group can be reached 8:00 AM to 5:00 PM, Pacic
Time, Monday through Friday, excluding U.S. holidays.
Please try to call from a phone near your computer system and Sync
Station 16.
X Access is available 24 hours a day, 365 days a year, via:
The World Wide Web at: www.aleratec.com
www.aleratec.com
12
Service and Support
Please Note:
This Warranty is valid only within the United States and Puerto Rico,
and applies only to products that are new and unopened on the date
of purchase. For areas outside the United States and Puerto Rico,
contact the authorized dealer from whom you purchased this product to
determine which warranty, if any, applies.
THIS LIMITED WARRANTY CONSTITUTES YOUR SOLE AND
EXCLUSIVE REMEDY, AND THE SOLE AND EXCLUSIVE
LIABILITY OF ALERATEC, INC., AND IS IN LIEU OF ALL
OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF
MERCHANTABILITY OF ITEMS FOR A PARTICULAR PURPOSE.
Your sole remedy shall be repair or replacement, with new or
refurbished components, as provided in this Limited Warranty.
Aleratec, Inc. shall not be liable for any direct, indirect, special
incidental products or consequential damages, including, but not
limited to, any loss of data or loss of prots or business, regardless of
the form of action or theory of liability resulting from any defect in,
or use of, this product (even if Aleratec, Inc. has been advised of the
possibility of such damages).
In any event, the liability of Aleratec, Inc. under this Limited Warranty,
for damages to you or any third party, regardless of the form of action
or theory of liability, shall not exceed the purchase price you paid for
this product.
Some states do not allow limitations of the disclaimer of implied
warranties, the period an implied warranty lasts, or the exclusion or
limitation of incidental or consequential damages, so the exclusions and
limitations stipulated in this Limited Warranty may not apply to you.
This Limited Warranty gives you specic legal rights, and you may
have other rights which vary from state to state.
www.aleratec.com
13
Service and Support
Aleratec, Inc., Limited Warranty
This Limited Warranty covers defects encountered in the course of
normal use of this product and does not apply to damage from improper
use, abuse, accidents, unauthorized service, or inadequate packaging
when shipping the product to Aleratec, Inc.
Aleratec, Inc. provides the following limited warranty for this product
only if the product was originally purchased for use, not re-sale, from
Aleratec, Inc., an Aleratec, Inc. authorized dealer or distributor, or any
other Aleratec, Inc. approved reseller for this product. This product is
warranted to be free from defects in workmanship and material for a
period of one year from the date of your original purchase.
If the product fails during normal and proper use within the warranty
period, Aleratec, Inc. will, at its option, repair or replace the product at
no cost (except shipping and insurance). This limited warranty does not
include service to repair damage from improper installation, accident,
disaster, misuse, abuse, or modications to the subsystem, or by any
other causes unrelated to defective materials or workmanship.
To Obtain Warranty Service:
You must ship your subsystem to the authorized dealer where your
subsystem was purchased within the one year warranty period and
no later than thirty days after discovery of claimed defect, whichever
occurs rst. In either case, you must provide proof of original purchase
before any warranty service can be performed. Products and parts
provided as a result of warranty service may be other than new but
will be in good working order and become your property at the time of
exchange. At the same time, the exchanged products or parts become
the property of Aleratec, Inc.
When shipping the subsystem for service, you agree to insure the
subsystem, to prepay shipping charges, and to use the original shipping
container or equivalent. Any service outside the scope of this limited
warranty shall be at Aleratec, Inc.’s or its Authorized Service Provider’s
rates and terms then in effect.
This warranty gives you specic legal rights; you may also have other
rights which vary from state to state.
400107_UG_EN_Rev. A Copyright © 2014
Specifications subject to change without notice.
Aleratec, Inc.
9851 Owensmouth Avenue
Chatsworth, CA 91311 U.S.A.
www.aleratec.com
/